Mitsubishi Electric FL7000LU Control Manual
Mitsubishi electric lcd projector specification sheet
Hide thumbs
Also See for FL7000LU:
- Specifications (2 pages) ,
- User manual (50 pages) ,
- Product manual (10 pages)
Table of Contents
Advertisement
Quick Links
LCD Projector
FL7000U/FL7000LU
Controlling the projector using a personal computer
This projector can be controlled by connecting a personal computer with RS-232C terminal.
PC-controllable functions:
• Turning the power ON or OFF
• Changing input signals
• Inputting commands by pressing the buttons on the control panel and remote control
• Menu setting
Connection
To RS-232C
terminal
Important:
• Connect the computer with the projector on a one-to-one basis.
• Make sure that your computer and projector are turned off before connection.
• Boot up the computer first, and then plug the power cord of the projector.
(If you do not follow this instruction, the Com port may not function.)
• Adapters may be necessary depending on the PC connected to this projector. Contact your dealer for details.
1. Interface
1.1 Pin assignment of SERIAL terminal (D-SUB 9-pin)
Pin No.
Name
1
OPEN
2
RXD
3
TXD
4
OPEN
5
GND
6
OPEN
7
OPEN
8
OPEN
9
OPEN
1.2 Communications format
PROTOCOL
BAUD RATE
DATA LENGTH
PARITY BIT
STOP BIT
FLOW CONTROL
This projector uses RXD, TXD and GND lines for RS-232C control.
For RS-232C cable, the reverse type cable should be used.
RS-232C cable
D-SUB 9-pin
I/O
IN
OUT
RS-232C
9600 [bps]
8 [bits]
NONE
1 [bit]
NONE
D-SUB 9-pin
1
SERIAL
Advertisement
Table of Contents
Related Manuals for Mitsubishi Electric FL7000LU
Summary of Contents for Mitsubishi Electric FL7000LU
-
Page 1: Lcd Projector
• Boot up the computer first, and then plug the power cord of the projector. (If you do not follow this instruction, the Com port may not function.) • Adapters may be necessary depending on the PC connected to this projector. Contact your dealer for details. 1. Interface 1.1 Pin assignment of SERIAL terminal (D-SUB 9-pin) -
Page 2: Control Command Diagram
(2) In the process of the auto position (3) After the power is turned on. The projector receives no commands for about 20 seconds (or for 2 minutes at the longest if the lamp does not light up promptly as the life is expiring.) •... - Page 3 → Check that the RS-232C cable is connected. → Check the RS-232C cable for electrical discontinuity. • The projector is in the state of being unable to send out a command. → Use command “00vST” to check if the projector operates normally.
-
Page 4: Command List
The operation commands are used for the basic operation setting of this projector. They may not be executed while the signals are changed. The operation commands have no data codes. -
Page 5: Remote Commands
Error status The PC sends the command without attaching the data code to it. On the other hand, the projector attaches to the received command its current operating status as the data code and send it back to the PC. -
Page 6: Direct Commands
(Not executable in stand-by mode. When the mute commands are sent while the splash screen is being displayed, the splash screen is not muted but only canceled.) The mute commands are used for the mute setting of this projector with the 0 (30h) and 1 (31h). ITEM... - Page 7 00–20 53h 48h 4Ch 53h 00–20 53h 48h 52h 53h 00–20 Status code from the projector ‘30’ ‘30’ ‘41’ ‘50’ ‘4F’ ‘4E’ ‘31’ ‘0D’ 00APON1 Data ), 01 (English), 02 (Español), 03 (Deutsch), ), 07 ( ), 09 (PORTUGUÊS), 11 (SVENSKA),...
-
Page 8: Password Lock Commands
4 to 8-digit password comprised of any figures 1 to 4 added to the end of the data code. When the password lock is enabled or disabled successfully, the projector sends a return command comprising the data code, password, and “1”...