Page 1 Australian Model Chinese Model DCR-PC100E E Model Hong Kong Model Ver 1.0 1999. 09 Tourist Model Photo : DCR-PC100 DCR-PC100/PC100E D300 MECHANISM DCR-PC100 : NTSC model For MECHANISM ADJUSTMENTS, refer to the “DV MECHANICAL DCR-PC100E : PAL model ADJUSTMENT MANUAL D MECHANISM ”...
Page 2 MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
Page 3: Table Of Contents
TABLE OF CONTENTS SERVICE NOTE Recording still images on “Memory Stick”s –Memory photo recording ··················································· 1-28 POWER SUPPLY DURING REPAIRS ····························· 6 Superimposing a still picture in a “Memory Stick” TO TAKE OUT A CASSETTE WHEN NOT EJECT on a moving picture –MEMORY MIX ································ 1-29 (FORCE EJECT) ································································...
Page 4 • VC-227 (MEMORY STICK I/F)(4/15) • VF-138 (LCD DRIVER)(1/2) SCHEMATIC DIAGRAM ···························· 4-19 SCHEMATIC DIAGRAM ···························· 4-81 • VC-227 (AGC, AFC, ND CONT, (BBI))(5/15) • VF-138 (BACK LIGHT DRIVER)(2/2) SCHEMATIC DIAGRAM ···························· 4-21 SCHEMATIC DIAGRAM ···························· 4-83 • VC-227 (LINE OUT AMP)(6/15) •...
Page 5 White Balance Adjustment (VF-138 board) ·················· 5-32 IR Video Deviation Adjustment (MR-44 board) ··········· 5-55 1-5. LCD SYSTEM ADJUSTMENT ··································· 5-33 IR Audio Deviation Adjustment (MR-44 board) ··········· 5-56 VCO Adjustment (PD-125 board) ································· 5-33 3-6. AUDIO SYSTEM ADJUSTMENTS ···························· 5-57 Black Limit Adjustment (PD-125 board) ······················...
Page 6: Service Note
SERVICE NOTE POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off so that the unit cannot operate. This following two methods are available to prevent this. Take note of which to use during repairs.
Page 7: Self-Diagnosis Function
SELF-DIAGNOSIS FUNCTION SELF-DIAGNOSIS DISPLAY SELF-DIAGNOSIS FUNCTION When problems occur while the unit is operating, the counter of the When problems occur while the unit is operating, the self-diagnosis viewfinder, LCD screen or LCD window consists of an alphabet function starts working, and displays on the viewfinder, LCD screen or LCD window what to do.
Page 8: Self-Diagnosis Code Table
SELF-DIAGNOSIS CODE TABLE Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Non-standard battery is used. Use the info LITHIUM battery. Condensation. Remove the cassette, and insert it again after one hour. Video head is dirty. Clean with the optional cleaning cassette. LOAD direction.
Page 9 DCR-PC100/PC100E SECTION 1 This section is extracted from instruction GENERAL manual. (DCR-PC100E model)
Page 18 1-10...
Page 19 1-11...
Page 20 1-12...
Page 21 1-13...
Page 22 1-14...
Page 23 1-15...
Page 24 1-16...
Page 25 1-17...
Page 26 1-18...
Page 27 1-19...
Page 28 1-20...
Page 29 1-21...
Page 30 1-22...
Page 31 1-23...
Page 32 1-24...
Page 33 1-25...
Page 34 1-26...
Page 35 1-27...
Page 36 1-28...
Page 37 1-29...
Page 38 1-30...
Page 39 1-31...
Page 40 1-32...
Page 41 1-33...
Page 42 1-34...
Page 43 1-35...
Page 44 1-36...
Page 45 1-37...
Page 46 1-38...
Page 47 1-39...
Page 48 1-40...
Page 49 1-41...
Page 50 1-42...
Page 51 1-43E...
Page 52 DCR-PC100/PC100E SECTION 2 DISASSEMBLY The following flow chart shows the disassembly procedure. 2-1. LCD unit, PD-125 board LCD service position 2-2. MD block-1 MD block service position-1 Note : Use the parts only which can be removed easily from outside of the MD block.
Page 53: Lcd Unit, Pd-125 Board
NOTE: Follow the disassembly procedure in the numerical order given. 2-1. LCD UNIT, PD-125 BOARD 2 LCD cabinet (R) 4 Screw (M1.7 × 2.5), 1 Two screws (M1.7 × 2.5), assembly lock ace, p2 lock ace, p2 REMOVING THE PD-125 BOARD 9 Screw (M1.7 ×...
Page 54: Md Block-1
2-2. MD BLOCK-1 3 Two screws (M1.7 × 4), lock ace, p2 4 Shoe cover 5 Screw (M1.7 × 4), lock ace, p2 9 Cabinet (L) block assembly 8 Screw (M1.7 × 4), lock ace, p2 7 Push the eject knob in the direction of the arrow, and open the cassette lid.
Page 55: Board, Md Block-2
2-3. MR-44 BOARD, MD BLOCK-2 1 Three screws (M1.7 × 2.5), lock ace, p2 3 IR window When re-assembling, attach it to the cabinet (R) block assembly before installing the MD block. 2 MR-44 board (100P) 6 MD block MD frame, Cover assembly 4 Two screws (M1.7 ×...
Page 56: Lens Assembly, Evf Block Assembly, Control Switch Block (Me-4950)
2-4. LENS ASSEMBLY, EVF BLOCK ASSEMBLY, CONTROL SWITCH BLOCK (ME-4950) [REMOVING THE CONTROL 6 EVF block assembly SWITCH BLOCK (ME-4950)] 1 Control switch block (ME-4950) (5P) 5 VF-138 board (20P) 4 Screw (M1.7 × 2.5), lock ace, p2 3 Control switch block (ME-4950) 2 CCD/CD block assembly (CD-234 board) (60P)
Page 57: Hinge Assembly
2-6. HINGE ASSEMBLY Perform the disassembling after steps 1 – 6 of 2-1 is complete. 1 Release the claw (a) in the [REMOVING THE HINGE ASSEMBLY] direction of the arrow B first then release the two claws (b). 4 Blind plate assembly 1 PT-125 claw (b) harness...
Page 58: Board
[SERVICE POSITION (Mainly for voltage measurement and check)] MD block MD frame, Cover assembly MR-44 board - 4 4 Insert an insulation sheet a r d between the MD block and the VC-227 (VC-227P) board. DC-IN connector FJ-25 board (50P) CPC-8 jig AC adaptor MR-44 board...
Page 59: Assembly
2-8. CCD/CD BLOCK ASSEMBLY, MF RING BLOCK ASSEMBLY 3 Flexible board 6 CCD/CD block assembly (from lens device) (33P) 4 Tapping screw Never remove the CCD imager (M1.7 × 4) (IC101) from the CD-234 board 2 CD heat sink/ because position alignment CD insulating sheet/ 1 Tapping screw between the CCD imager and...
Page 60 2-10.CONTROL SWITCH BLOCK (FK-4950) 3 FK flexible clamp 5 Screw (M1.7 × 2.5), lock ace, p2 4 Six screws (M1.7 × 2.5), 6 Remove an end of lock ace, p2 the grip belt from 1 Remove the two claws the bracket cap. 2 FP-128 flexible board (30P) 1 Screw (M1.7 ×...
Page 61 2-11.CIRCUIT BOARDS LOCATION VF-138 MA-367 (LCD DRIVER, BACK LIGHT DRIVER) (MIC AMP) CD-234 (CCD IMAGER) PD-125 (RGB DRIVER, TG) MR-44 CONNECTOR, DRUM/CAPSTAN MOTOR DRIVE, TIMING GENERATOR, REC/PB HEAD AMP, INVERTER LASER LINK TRANSFORMER UNIT VC-227 A/D, CAMERA CONTROL, JPEG DIGITAL STILL CONTROL, MEMORY STICK I/F, AGC, AFC, LINE OUT AMP, VFD, SFD, LIP/TFD, ZOOM MOTOR CONTROL,...
Page 62: Control Switch Block (Fk-4950)
2-12.FLEXIBLE BOARDS LOCATION FP-130 From INTELLIGENT CONTROL SWITCH BLOCK ACCESSORY SHOE (FK-4950) CONTROL SWITCH BLOCK (ME-4950) FP-128 From CONTROL SWITCH BLOCK (FK-4950) (From LENS BLOCK) FP-586 (From LOADING MOTOR) (From DRUM MOTOR) (From VIDEO HEAD) FP-91 (MODE) FP-92 FP-129 FP-242 TOP/END SENSOR, (PANEL OPEN) (S/T REEL SENSOR)
Page 63: Block Diagrams
DCR-PC100/PC100E SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM-1 ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. VC-227 BOARD(1/3) IC251 (4-15) (CARILLON) LENS ASSY CD-234 BOARD SPCK1 IRIS (SHUTTER) SPCK0...
Page 64: Overall Block Diagram-2
DCR-PC100/PC100E OVERALL BLOCK DIAGRAM-2 ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. CN2903 D-300MECHA DECK FOR ADJUSTMENTS (4-52) (4-58) VC-227 BOARD(2/3) (4-55) IC1816 CN2301 IC1900 SPCK1 SPCK1 CN1810 CRCK CRCK...
Page 65: Overall Block Diagram-3
DCR-PC100/PC100E OVERALL BLOCK DIAGRAM-3 ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. VC-227 BOARD(3/3) CONTROL SWITCH BLOCK(ME-4950) (4-38) (4-70) IC2204 MR-44 BOARD S1101-1112 (4-51) (2/2) CN1001 CN2917 MEMORY FUNCTION SW,...
Page 66: Power Block Diagram-1
DCR-PC100/PC100E 3-2. POWER BLOCK DIAGRAM-1 ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. FJ-25 BOARD VC-227 BOARD(1/2) SHOE ON BATT SIG (4-61) INIT CHARGE ON VTR DD ON BATT FET ON...
Page 67: Power Block Diagram-2
DCR-PC100/PC100E POWER BLOCK DIAGRAM-2 ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. VC-227 BOARD IC2204 FP-128 (2/2) (4-38) HI CONTROL (FLEXIBLE) PD-125 BOARD CN002 LCD901 (4-69) SHOE ON BATT SENS...
Page 68: Printed Wiring Boards And Schematic Diagrams
DCR-PC100/PC100E SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM-1 J7301 (PLUG IN POWER) J7301 CN7306 CD-234 BOARD SHOE_UNREG LENS-ASSY CN001 CN002 SHOE_UNREG LANC_SIG MA-367 BOARD SHO_ID1 SE451 ENC-03L INTELLGENT FP-130 NIGHT SHOT SHO_ID2 ACCESSORY MIC_GND FLEXIBLE...
Page 69: Frame Schematic Diagram-2
DCR-PC100/PC100E FRAME SCHEMATIC DIAGRAM-2 D-300 MECHANISM ND901 BACK-LIGHT IC2301 CN8200 CN2303 M903 LOADING LM_UNLOAD LM_UNLOAD N.C. /COM MOTOR REMOTE FP-586 COMMANDER LM_LOAD LM_LOAD COM /SMON2 RECEIVER INVERTER BLOCK DEW- DEW- VST /HST FLEXIBLE (BACK LIGHT DRIVER) SENSOR DEW+ DEW+ VCK /XHST...
Page 70: Schematic Diagrams
DCR-PC100/PC100E DCR-PC100/PC100E 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) (Measuring conditions voltage and waveform) •...
Page 71 DCR-PC100/PC100E CD-234 (CCD IMAGER) PRINTED WIRING BOARD — Ref. No. CD-234 Board; 4,000 Series — Do not remove the CCD imager become position alignment between the CCD imager and the CD-234 board is extremely difficult. These two parts are supplied together .
Page 72 DCR-PC100/PC100E CCD IMAGER 4-10 CD-234...
Page 73 DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-7 for printed wiring board. • Refer to page 4-87 for waveforms. CD-234 BOARD NO MARK:REC/PB MODE CCD IMAGER -REF.NO.:4000 SERIES- XX MARK:NO MOUNT Schematic diagrams and printed wiring boards C102 R101 0.1u...
Page 74: A/D Converter
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. • Refer to page 4-87 for waveforms. VC-227 BOARD(1/15) NO MARK:REC/PB MODE R :REC MODE A/D CONVERTER(CH BLOCK) P :PB MODE -REF.NO.:10000 SERIES- XX MARK:NO MOUNT C202...
Page 75: Camera Signal Processor
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. • Refer to page 4-87 for waveform. D_3.1V VC-227 BOARD(2/15) FB254 NO MARK:REC/PB MODE 2.8V FB251 CAMERA SIGNAL PROCESSOR R :REC MODE (CA BLOCK) P :PB MODE 1.9V...
Page 76: Jpeg, Digital Still Control
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. JIDCLK VC-227 BOARD(3/15) XJIEOD XJBUSY JPEG,DIGITAL STILL CONTROL SYSCLK (SF1-1 BLOCK) XSTART XJSTART -REF.NO.:10000 SERIES- MSEL XJMSEL XX MARK:NO MOUNT JID0 CARILLON_XCS JID0 JID1 NO MARK:REC/PB MODE...
Page 77 DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. • Refer to page 4-87 for waveform. VC-227 BOARD(4/15) 2.8V TO(15/15) R799 MEMORY STICK I/F(SF1-2 BLOCK) 100k -REF.NO.:10000 SERIES- C774 R801 R817 R816 XX MARK:NO MOUNT ML2201-100MBZ060 0.1u...
Page 78: Agc, Afc, Nd Cont (Bbi
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. • Refer to page 4-87 for waveforms. VC-227 BOARD(5/15) NO MARK:REC/PB MODE R :REC MODE AGC,AFC,ND CONT(BBI)(IN BLOCK) P :PB MODE -REF.NO.:10000 SERIES- XX MARK:NO MOUNT 2.8V A_2.8V...
Page 79: Line Out Amp
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. • Refer to page 4-88 for waveforms. VC-227 BOARD(6/15) LINE OUT AMP(AOI BLOCK) 2.8V -REF.NO.:10000 SERIES- 4.6V TO(15/15) XX MARK:NO MOUNT Q1400 R1401 C1418 2SD2216J-QR(K8).SO NO MARK:REC/PB MODE...
Page 80: Vfd
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. • Refer to page 4-88 for waveforms. Q1500 Q1501 Q1503 VC-227 BOARD(7/15) L1500 FB1501 2SD2216J-QR(K8).SO 2SD2216J-QR(K8).SO 2SD2216J-QR(K8).SO 100uH BUFFER BUFFER BUFFER VFD (VFD BLOCK) R1510 R1507 R1521 -REF.NO.:10000 SERIES-...
Page 81: Sfd
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. • Refer to page 4-88 for waveforms. VC-227 BOARD(8/15) SFD (JC-1 BLOCK) SIGNAL PATH -REF.NO.:10000 SERIES- VIDEO SIGNAL XX MARK:NO MOUNT AUDIO NO MARK:REC/PB MODE CHROMA Y/CHROMA...
Page 82: Lip/Tfd
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. VC-227 BOARD(9/15) LIP/TFD (JC-2 BLOCK) -REF.NO.:10000 SERIES- XX MARK:NO MOUNT SIGNAL PATH NO MARK:REC/PB MODE R :REC MODE P :PB MODE VIDEO SIGNAL AUDIO CHROMA Y/CHROMA SIGNAL...
Page 83: Focus/Zoom Motor Control
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. • Refer to page 4-88 for waveform. A_3.1V TO(15/15) I_HALL_GAIN VC-227 BOARD(10/15) IRIS_PWM FOCUS/ZOOM MOTOR CONTROL I_HALL_OFFSET (LD BLOCK) L403 10uH -REF.NO.:10000 SERIES- R423 I_HALL_AD XX MARK:NO MOUNT...
Page 84: Camera Control
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. • Refer to page 4-88 for waveform. VC-227 BOARD(11/15) F_TALLY_LED_ON TO(12/15) FK_LED_ON CAMERA CONTROL(MC BLOCK) TO(13/15) IR_LED_ON -REF.NO.:10000 SERIES- SHOE_ID2 XX MARK:NO MOUNT TO(14/15) R330 C309 SHOE_ID1 0.1u...
Page 85: Mode Control
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. • Refer to page 4-88 for waveforms. L2400 10uH VC-227 BOARD(12/15) 2.8V C2411 MT_4.8V MODE CONTROL(MD1 BLOCK) TO(15/15) 6.3V RP_4.6V -REF.NO.:10000 SERIES- R2432 100k UNREG XX MARK:NO MOUNT 4.6V...
Page 86: Hi Control)
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. • Refer to page 4-89 for waveforms. • Refer to page 4-46 for FP-129 flexible wiring board. VC-227 BOARD(13/15) Q2202 XP4501-TXE TO CN HI CONTROL(HI BLOCK) BUFFER...
Page 87: Audio
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. VC-227 BOARD(14/15) NO MARK:REC/PB MODE AUDIO(AU BLOCK) R :REC MODE P :PB MODE -REF.NO.:10000 SERIES- XX MARK:NO MOUNT C2016 0.47u R2028 R2038 L_IO C2053 0.01u R2031 TO(15/15)
Page 88: Dc/Dc Converter
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. • Refer to page 4-89 for waveforms. V_IO VC-227 BOARD(15/15) CN2904 AV_JACK_IN TO(13/15) AV_JACK_IN TO(6/15) DC/DC CONVERTER(DD BLOCK) SIGNAL PATH V_IO -REF.NO.:10000 SERIES- AV_GND REC/PB TO(12/15) HP_JACK_IN...
Page 89: Memory Stick I/F, Agc, Afc, Line Out Amp
DCR-PC100/PC100E VC-227 (A/D, CAMERA CONTROL, JPEG, MEMORY STICK I/F, AGC, AFC, LINE OUT AMP, VFD, SFD, LIP/TFD, ZOOM MOTOR CONTROL, MODE CONTROL, HI CONTROL, AUDIO, DC/DC CONVERTER) PRINTED WIRING BOARD — Ref. No. VC-227 Board; 10,000 Series — For printed wiring board •...
Page 90: Panel Open)
DCR-PC100/PC100E FP-129 (PANEL OPEN) FLEXIBLE BOARD — Ref. No. FP-129 Board; 4,000 Series — FP-129 FLEXIBLE BOARD S002 (PANEL OPEN) S001 (PANEL REV) 1-675-716- (From LENS BLOCK) FP-129 FP-242 (PANEL OPEN) (S/T REEL SENSOR) A/D, CAMERA, JPEG, MS I/F, AGC, AFC, LINE OUT, VFD, SFD, LIP/TFD, ZOOM MOTOR, MODE, HI, AUDIO, DC/DC CONVERTER...
Page 91: Drive, Timing Generator, Rec/Pb Head Amp, Laser Link)
DCR-PC100/PC100E MR-44 (CONNECTOR, DRUM/CAPSTAN MOTOR DRIVE, TIMING GENERATOR, REC/PB HEAD AMP, LASER LINK) PRINTED WIRING BOARD — Ref. No. MR-44 Board; 10,000 Series — For printed wiring board • Refer to page 4-94 for location. • This board is six-layer print board. However, the pat- terns of layers two to five have not been included in the diagram.
Page 92: Mode), Fp-92 (Top/End Sensor, Tape Led), Fp-242 (S/T Reel Sensor) Printed Wiring Boards
DCR-PC100/PC100E FP-91 (MODE), FP-92 (TOP/END SENSOR, TAPE LED), FP-242 (S/T REEL SENSOR) PRINTED WIRING BOARDS — Ref. No. FP-91, 92, 242 Flexible Boards; 10,000 Series — FP-91 FLEXIBLE FP-92 FLEXIBLE BOARD BOARD CN902 S902 MODE SWITCH CN903 Q901 TAPE TOP...
Page 93: Connector
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-47 for printed wiring board. MR-44 BOARD(1/5) CONNECTOR(CN1 BLOCK) D MECHA DECK(2/2) LN2301 CN2302 CN902 -REF.NO.:10000 SERIES- (D300) XX MARK:NO MOUNT LN2302 TO(2/5) DRUM PG/FG NO MARK:REC/PB MODE SENSER_VCC SENSER_VCC SENSER_VCC R2315...
Page 94: Drum/Capstan Motor Drive
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-47 for printed wiring board. • Refer to page 4-89 for waveforms. MR-44 BOARD(2/5) TO(1/5) 2.8V DRUM/CAPSTAN MOTOR TO(1/5) UNREG DRIVE(MD2 BLOCK) MT_GND TO(1/5) -REF.NO.:10000 SERIES- MT_4.8V R2569 R2578 2200 C2573 XX MARK:NO MOUNT C2566 4.7u...
Page 95: Id Detect, Timing Generator
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-47 for printed wiring board. • Refer to page 4-89 for waveforms. FB1901 MR-44 BOARD(3/5) 2.8V TO(1/5) ID DETECT. TIMING GENERATOR TO(1/5) 1.9V (RF2 BLOCK) TO(1/5) -REF.NO.: SERIES- C1903 XX MARK:NO MOUNT 4.7u...
Page 96: Rec/Pb Head Amp
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-47 for printed wiring board. • Refer to page 4-90 for waveforms. MR-44 BOARD(4/5) Q1810 2SB1462J-QR(K8).SO REC/PB HEAD AMP (RF1 BLOCK) R0/P2.5 R1875 SIGNAL PATH -REF.NO.: SERIES- XX MARK:NO MOUNT VIDEO SIGNAL...
Page 97: Laser Link
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-47 for printed wiring board. • Refer to page 4-90 for waveforms. L7500 MR-44 BOARD(5/5) 10uH ± 10% LASER LINK(IR BLOCK) -REF.NO.:10000 SERIES- R7514 XX MARK:NO MOUNT C7513 L7501 L7502 NO MARK:REC/PB MODE...
Page 98: Video In/Out, Dc In
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-63 for printed wiring board. Q914 Q915 2SB1581-T1 2SB1462J-QR(K8).SO FJ-25 BOARD VIDEO IN/OUT,DC IN 5.0V -REF.NO.:4000 SERIES- R916 XX MARK:NO MOUNT R920 NO MARK:REC/PB MODE ± 0.5% C919 Q916 Q914-916 XP4501-TXE MT4.6V SWITCH/REG.
Page 99: Printed Wiring Board
DCR-PC100/PC100E FJ-25 (VIDEO IN/OUT, DC IN) PRINTED WIRING BOARD — Ref. No. FJ-25 Board; 4,000 Series — AUDIO VIDEO For printed wiring board • Refer to page 4-94 for location. VC-227 • This board is six-layer print board. However, the pat-...
Page 100 DCR-PC100/PC100E VIDEO VIDEO IN/OUT, DC IN 4-65 4-66 FJ-25...
Page 101: Control Switch Block (Fk-4950)
DCR-PC100/PC100E CONTROL SWITCH BLOCK (FK-4950) JP006 PHOTO -REF.NO.:10000 SERIES- XX MARK:NO MOUNT S1056 PHOTO FREEZE + SLOW SHUTTER S1009 STOP PHOTO REC KEY_AD3 KEY_AD0 S1053/S1050 R1056 SEL/PUSH EXEC 1200 R1003 R1010 1200 S1010 D1003 R1058 DIAL B TLSU1008(T05,SOY) 4700 (LASER AV LINK)
Page 102 DCR-PC100/PC100E CONTROL SWITCH BLOCK(ME-4950) FP-128 FLEXIBLE -REF.NO.:10000 SERIES- -REF.NO.:4000 SERIES- XX MARK:NO MOUNT XX MARK:NO MOUNT TO CONTROL SWITCH BLOCK(FK-4950) CONTROL SWITCH BLOCK(ME-4950) is replaced as a block. CN1051 So that this PRINTED WIRING BOARD is omitted. (SEE PAGE 4-68)
Page 103 DCR-PC100/PC100E MA-367 (MIC AMP) PRINTED WIRING BOARD — Ref. No. MA-367 Board; 10,000 Series — PLUG IN POWER For printed wiring board VF-138 MA-367 • Refer to page 4-95 for location. (LCD DRIVER, BACK LIGHT DRIVER) (MIC AMP) • This board is six-layer print board. However, the pat-...
Page 104: Mic Amp
DCR-PC100/PC100E MA-367 BOARD SE450 ENC-03L SIGNAL PATH MIC AMP C7329 -REF.NO.:10000 SERIES- C7308 R7324 1608 AUDIO 6.3V C7315 C7322 XX MARK:NO MOUNT 0.001u SIGNAL 1608 (YAW SENSOR) C7321 YS_OUT NO MARK:REC/PB MODE 100p C7330 YS_REF C7343 SE451 470p ENC-03L R7320...
Page 105: Printed Wiring Board
DCR-PC100/PC100E PD-125 (RGB DRIVER, TG) PRINTED WIRING BOARD — Ref. No. PD-125 Board; 10,000 Series — For printed wiring board • Refer to page 4-95 for location. • This board is four-layer print board. However, the pat- terns of layers two to four have not been included in the diagram.
Page 106: Rgb Driver
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-90 for waveforms. PD-125 BOARD(1/2) RGB DRIVER(PD-1 BLOCK) -REF.NO.:10000 SERIES- SH1_Y XX MARK:NO MOUNT SH2_Y SH3_Y NO MARK:REC/PB MODE L8001 L8002 10uH 10uH SH4_Y PRG_Y TO(2/2) XCLP XCLP_Y SIGNAL PATH R8017 R8022...
Page 107 DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-75 for printed wiring board. • Refer to page 4-90 for waveforms. PD-125 BOARD(2/2) TG(PD-2 BLOCK) -REF.NO.:10000 SERIES- XX MARK:NO MOUNT NO MARK:REC/PB MODE R8223 SH1_Y SH2_Y C8215 SH3_Y SH4_Y R8226 R8249...
Page 108: Lcd Driver
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-85 for printed wiring board. • Refer to page 4-91 for waveforms. VF-138 BOARD(1/2) LCD DRIVER(VF BLOCK) -REF.NO.:10000 SERIES- L5001 XX MARK:NO MOUNT 22uH (2016) NO MARK:REC/PB MODE SIGNAL PATH VIDEO SIGNAL...
Page 109: Back Light Driver
DCR-PC100/PC100E VF-138 BOARD(2/2) NO MARK:REC/PB MODE BACK LIGHT DRIVER(VFIED BLOCK) -REF.NO.:10000 SERIES- XX MARK:NO MOUNT R5511 C5500 Q5507 6.3V C5501 0.1u C5502 R5512 CN5501 VCC1 VCC1 Q5506 LED902 R5513 R5502 R5503 LED1 LED1 BACK-LIGHT 8200 LED2 LED2 LED3 LED3 LED4...
Page 110: Lcd Driver, Back Light Driver
DCR-PC100/PC100E VF-138 (LCD DRIVER, BACK LIGHT DRIVER) PRINTED WIRING BOARD — Ref. No. VF-138 Board; 1,000 Series — For printed wiring board VF-138 MA-367 • Refer to page 4-96 for location. (LCD DRIVER, BACK LIGHT DRIVER) (MIC AMP) • This board is six-layer print board. However, the patterns of...
Page 111 DCR-PC100/PC100E 4-3. WAVEFORMS CD-234 VC-227 VC-227 VC-227 VC-227 VC-227 VC-227 BOARD BOARD (1/15) BOARD (5/15) BOARD (6/15) BOARD (7/15) BOARD (8/15) BOARD (11/15) CAMERA REC/PB CAMERA REC/PB CAMERA REC/PB IC201 2 - qa IC302 r; (X301) IC102 9 IC1200 wg (C1200)
Page 112: Waveforms
DCR-PC100/PC100E VC-227 MR-44 MR-44 BOARD (13/15) BOARD (2/5) BOARD (3/5) CAMERA REC/PB CAMERA REC/PB IC1900 qa IC2204 r; (X2200) CAMERA REC IC2503 4 IC2504 qj 2.0Vp-p 2.7Vp-p 2.6Vp-p 3.0Vp-p 20.0MHz 25nsec 6.7msec 0.92msec IC1900 ws – wh IC2204 td CAMERA REC...
Page 113 DCR-PC100/PC100E MR-44 PD-125 PD-125 MR-44 BOARD (5/5) BOARD (1/2) BOARD (4/5) BOARD (2/2) CAMERA REC/PB CAMERA REC/PB CAMERA REC/PB IC1814 qg – w; IC7501 7 (IR ON) IC8001 8 IC8201 w; 2.0Vp-p 0.4Vp-p 0.25Vp-p 2.8Vp-p 25nsec 0.3µsec IC1814 rs PB...
Page 114 DCR-PC100/PC100E VF-138 BOARD (1/2) CAMERA REC/PB IC5000 8 IC5002 rg 2.8Vp-p 0.4Vp-p IC5000 9 0.2Vp-p IC5000 0 0.2Vp-p IC5000 w; 7Vp-p IC5000 ws 7Vp-p IC5000 wf 7Vp-p IC5002 wj 2.8Vp-p IC5002 ra 2.8Vp-p 16.5MHz WAVEFORMS 4-91...
Page 115: Mounted Location
DCR-PC100/PC100E 4-4. MOUNTED LOCATION CD-234 BOARD (SIDE A) VC-227 BOARD (SIDE A) IC101 C211 C1615 L251 R771 R1689 G-1 C213 C1616 L1200 R772 R1694 D-2 C251 C1617 L1201 R773 R1695 D-2 C252 C1619 L1202 R774 R1696 D-2 CD-234 BOARD (SIDE B)
Page 116 DCR-PC100/PC100E VC-227 BOARD (SIDE B) C201 F-10 C1423 C3220 IC2203 D-12 R314 R470 E-12 R2217 D-11 R3213 B-10 C202 G-10 C1433 C3221 B-10 IC2204 D-11 R315 R471 E-12 R2218 D-11 R3214 B-10 C203 G-10 C1434 C3222 A-10 IC3250 G-9 R316...
Page 117 DCR-PC100/PC100E MR-44 BOARD (SIDE A) MR-44 BOARD (SIDE B) FJ-25 BOARD (SIDE A) FJ-25 BOARD (SIDE B) C1804 L1811 C2301 LN2302 F-6 C912 JL912 C910 A-15 FB954 B-11 C1833 L2512 C2302 LN2304 A-6 C913 JL913 C911 A-16 FB955 A-12 C1834...
Page 118 DCR-PC100/PC100E MA-367 BOARD (SIDE A) MA-367 BOARD (SIDE B) PD-125 BOARD C450 FB7302 C-4 C 7304 C-8 D 7309 C-7 C8001 LND810 D-1 R8052 D-2 C451 C 7305 C-7 D 7311 B-6 C8003 LND812 C-4 R8100 A-3 C7303 J7301 C 7307 C-7...
Page 119 DCR-PC100/PC100E VF-138 BOARD (SIDE A) VF-138 BOARD (SIDE B) C5000 E-3 R5010 E-3 C5017 C5001 R5011 E-3 C5018 C5002 R5012 E-3 C5019 C5003 R5013 E-3 C5020 C5004 R5014 E-3 C5021 C5005 R5015 E-3 C5022 C5006 R5016 D-4 C5024 C5007 R5017 D-4...
Page 120: Adjustments
DCR-PC100/PC100E SECTION 5 ADJUSTMENTS Before starting adjustment EVR Data Re-writing Procedure When Replacing Board The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.
Page 121: Adjusting Items When Replacing Main Parts And Boards
1-1. Adjusting items when replacing main parts and boards. • Adjusting items when replacing main parts When replacing main parts, adjust the items indicated by in the following table. Replaced parts Block replacement Parts replacement Adjustment Adjustment Section Initialization of C page data Initialization Initialization of D page data of B, C, D, E,...
Page 122 • Adjusting items when replacing a board or EEPROM When replacing a board or EEPROM, adjust the items indicated by in the following table. Replaced parts Board replacement Adjustment Adjustment Section Initialization of C page data Initialization Initialization of D page data of B, C, D, E, Initialization of B page data F, 7 page data...
Page 123: Camera Section Adjustment
5-1. CAMERA SECTION ADJUSTMENT 1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • Regulated power supply • Digital voltmeter Ref. No. Name Parts Code Usage Auto white balance adjustment/check Filter for color temperature correction (C14) J-6080-058-A White balance adjustment/check ND filter 1.0...
Page 124: Preparations
1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Pattern box Note 2: When performing only the adjustments, the lens block and boards need not be disassembled. Connect the equipment for adjustments according to Fig. 5-1-3. Note 3: As removing the cabinet (L) (removing CN1051 of the control switch block (FK-4950)) means removing the lithium 3V power 1.5 m...
Page 125 Cabinet (L) Lens block Viewfinder Control switch block (FK-4950) VF-138 board CN1051 CD-234 board CN101 Must be connected Must be connected when performing FP-128 flexible the color EVF system adjustments. MS holder Must be connected Must be connected when using when performing Cabinet (R) the MENU button.
Page 126: Precaution
1-1-3. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. POWER switch (FK-4950 block) ......CAMERA 16 : 9 WIDE (Menu setting) ..........OFF NIGHT SHOT switch (Lens block) ......... OFF PICTURE EFFECT (Menu setting) .........
Page 127: Initialization Of B, C, D, E, F, 7 Page Data
1-2. INITIALIZATION OF B, C, D, E, F, 7 PAGE DATA 3. C Page Table 1-2-1. INITIALIZATION OF C PAGE DATA Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the C Page 1. Initializing the C Page Data Data”.) Note: If the C page data has been initialized, the following adjustments Fixed data-2 : Modified data.
Page 128 Initial value Initial value Address Remark Address Remark NTSC PAL NTSC PAL Emergency memory address Fixed data-1 (Initialized data) Fixed data-1 (Initialized data) PLL f fine adj. Fixed data-2 Fixed data-1 (Modified data. Copy the data built in (Initialized data) the same model.) Fixed data-1 (Initialized data)
Page 129: Modification Of D Page Data
1-2-2. INITIALIZATION OF D PAGE DATA 1. Initializing the D Page Data Initial value Address Remark Note: If the D page data has been initialized, the following adjustments NTSC PAL need to be performed again. Fixed data-1 1) Modification of D page data 2) Color viewfinder system adjustments (Initialized data) 3) LCD system Adjustments...
Page 130 3. D Page Table Initial value Address Remark Note1: Fixed data-1 : Initialized data. (Refer to “1. Initializing the D Page NTSC PAL Data”.) Fixed data-2 Fixed data-2 : Modified data. (Refer to “2. Modification of D Page Data”.) (Modified data. Copy the data built in the same model.) Initial value Address...
Page 131: Initialization Of B Page Data
1-2-3. INITIALIZATION OF B PAGE DATA Note: When reading the B page data, insert a “Memory Stick” into the Initial value Address Remark “Memory Stick” slot. NTSC PAL Fixed data-2 Switch setting Fixed data-1 POWER ..............MEMORY Fixed data-2 1. Initializing the B Page Data (Modified data.
Page 132: Initializing The E, F, 7 Page Data
3. B Page Table 1-2-4. INITIALIZATION OF E, F, 7 PAGE DATA Switch setting Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the B Page POWER ..............CAMERA Data”.) Fixed data-2: Modified data. (Refer to “2. Modification of B Page 1.
Page 133 3. Modification of F Page Data 4. F Page Table Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, 7 Adjusting page Page Data”.) Adjusting Address 24 to 27, 29 to 2D, 8F, BC Fixed data-2: Modified data. (Refer to “2. Modification of E, F, 7 Page Data”).
Page 134 Initial value Initial value Address Remark Address Remark NTSC PAL NTSC PAL Auto white balance adj. Mechanical shutter data input. Fixed data-1 (Initialized data) Flange back adj. Fixed data-1 (Initialized data) MR adj. Max gain adj. Fixed data-1 Fixed data-2 Fixed data-3 (Refer to “3.
Page 135 Initial value Initial value Address Remark Address Remark NTSC PAL NTSC PAL Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-3 (Refer to “3.
Page 136 5. E Page Table Address Remark Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, 7 Fixed data-2 Page Data”.) (Modified data. Copy the data built in the same Fixed data-2: Modified data. (Refer to “2. Modification of E, F, 7 Page Data”.) model.) Address...
Page 137 Address Remark Address Remark Fixed data-1 (Initialized data) Fixed data-2 Fixed data-2 (Modified data. Copy the data built in the same (Modified data. Copy the data built in the same model.) model.) Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2...
Page 138: Page Table
6. 7 Page Table Address Remark Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, 7 Fixed data-1 Page Data”.) (Initialized data) Fixed data-2: Modified data. (Refer to “2. Modification of E, F, 7 Page Data”.) Initial value Address Remark Fixed data-2...
Page 139 Initial value Address Remark NTSC PAL 3) Select page: 0, address: 01, and set data: 00. Table. 5-1-7. 5-20...
Page 140: Camera System Adjustments
1-3. CAMERA SYSTEM ADJUSTMENTS Before perform the camera system adjustments, check that the specified values of “VIDEO SYSTEM ADJUSTMENT” are satisfied. 1. 54MHz/66MHz Origin Oscillation Adjustment 2. Zoom Key Center Adjustment (CD-234 board) Set the A/D value center of the microprocessor to the center voltage Set the frequency of the clock for synchronization.
Page 141: Hall Adjustment
3. HALL Adjustment 4. MR Adjustment For detecting the position of the lens iris and ND filter, adjust each The MR (Magnet resistor) adjustment of the inner focus lens is AMP gain and offset. carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing.
Page 142: Flange Back Adjustment
5. Flange Back Adjustment (Using Minipattern Box) The inner focus lens flange back adjustment is carried out Adjusting method: automatically. In whichever case, the focus will be deviated during Install the minipattern box so that the distance between it and auto focusing/manual focusing.
Page 143: More Than 500M Away)
6. Flange Back Adjustment (Using Flange Back Adjustment Chart and Subject More Than 500m Away) The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. 6-1. Flange Back Adjustment (1) 6-2.
Page 144: Flange Back Check
7. Flange Back Check 8. Picture Frame Setting Subject Siemens star Subject Color bar chart (2.0m from the front of the lens) (Color reproduction adjustment frame) (Luminance : approx. 200 lux) (1.5m from the front of the lens) Measurement Point Check operation on TV monitor Measurement Point Video output terminal...
Page 145: Color Reproduction Adjustment
35, 37, 3C, 3D Specified Value All color luminance points should settle within each color reproduction frame. Note: NTSC model: DCR-PC100 PAL model: DCR-PC100E Switch setting: 1) POWER ..............CAMERA 2) NIGHT SHOT ..............OFF 3) DIGITAL ZOOM (Menu display) ........OFF 4) STEADY SHOT (Menu display) ........
Page 146: Max Gain Adjustment
10. MAX GAIN Adjustment 11. Auto White Balance & LV Standard Data Input Setting the minimum illumination. Subject Clear chart If it is not consistent, the image level required for taking subjects in (Color reproduction adjustment frame) low illuminance will not be produced (dark). Measurement Point Display data of page 1 (Note3) Subject...
Page 147: Auto White Balance Adjustment
12. Auto White Balance Adjustment 13. White Balance Check Adjust to the proper auto white balance output data. Subject Clear chart If it is not correct, auto white balance and color reproducibility will (Color reproduction adjustment frame) be poor. Filter Filter C14 for color temperature Subject Clear chart...
Page 148: Mechanical Shutter Data Input
14. Mechanical Shutter Data Input 15. Angular Velocity Sensor Sensitivity Adjustment • This adjustment is performed only when replacing the angular velocity sensor. Adjustment Page Although this adjustment need not be performed when the circuit Adjustment Address 70 to 84 is damaged, etc., check the operations.
Page 149: Color Electronic Viewfinder
1-4. COLOR ELECTRONIC VIEWFINDER 1. VCO Adjustment (VF-138 board) Set the VCO free-run frequency. If deviated, the EVF screen will be SYSTEM ADJUSTMENT blurred. Note 1: When replacing the LCD unit, be careful to prevent damages caused by static electricity. Mode VTR stop Note 2: Set the switches as follows.
Page 150: Bright Adjustment (Vf-138 Board)
2. Bright Adjustment (VF-138 board) 3. Contrast Adjustment (VF-138 board) Set the level of the VIDEO signal for driving the LCD to the specified Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated value.
Page 151: White Balance Adjustment (Vf-138 Board)
4. White Balance Adjustment (VF-138 board) Correct the white balance. If deviated, the reproduction of the EVF screen may degenerate. Mode Camera Subject Arbitrary Measurement Point Check on EVF screen Measuring Instrument Adjustment Page Adjustment Address 71, 72 Specified Value The EVF screen should not be colored.
Page 152: Lcd System Adjustment
1-5. LCD SYSTEM ADJUSTMENT 1. VCO Adjustment (PD-125 board) Set the VCO free-run frequency. If deviated, the LCD screen will Note 1: The back light (fluorescent tube) is driven by a high voltage AC power supply. Therefore, do not touch the back light holder to be blurred.
Page 153: Black Limit Adjustment (Pd-125 Board)
2. Black Limit Adjustment (PD-125 board) 3. Bright Adjustment (PD-125 board) Set the dynamic range of the LCD driver to an appropriate level. If Set the level of the VIDEO signal for driving the LCD to an deviated, the LCD screen will become blackish or saturated appropriate level.
Page 154: Gamma-1 Adjustment (Pd-125 Board)
4. Gamma-1 Adjustment (PD-125 board) 5. Contrast Adjustment (PD-125 board) Set the level of the VIDEO signal for driving the LCD to an Set the level of the VIDEO signal for driving the LCD to an appropriate level. If deviated, the screen image will be blackish or appropriate level.
Page 155: Center Level Adjustment (Pd-125 Board)
6. Center Level Adjustment (PD-125 board) 7. White Balance Adjustment (PD-125 board) Set the video signal center level of LCD panel to an appropriate Correct the white balance. level. If deviated, the LCD screen color cannot be reproduced. Mode Camera Mode Camera Subject...
Page 156: Mechanism Section Adjustment
5-2. MECHANISM SECTION ADJUSTMENT On the mechanism section adjustment For detail of mechanism section adjustments, checks, and replacement of mechanism parts, refer to the separate volume “DV MECHANICAL ADJUSTMENT MANUAL D Mechanism ” and “DV MECHANICAL ADJUSTMENT MANUAL D200 Mechanism ”. 2-1.
Page 157: Video Section Adjustment
5-3. VIDEO SECTION ADJUSTMENT NTSC model : DCR-PC100 PAL model : DCR-PC100E 3-1. PREPARATIONS BEFORE ADJUSTMENTS Use the following measuring instruments for video section adjustments. 3-1-1. Equipment to Required 1) TV monitor 2) Oscilloscope (dual-phenomenon, band width above 30 MHz with delay mode) (Unless specified otherwise, use a 10 : 1 probe.)
Page 158: Precautions On Adjusting
3-1-2. Precautions on Adjusting Note 1: Setting the “Forced VTR Power ON” mode (VTR mode) The adjustments of this unit are performed in the VTR mode 1) Select page: 0, address: 01, and set data: 01. or camera mode. 2) Select page: D, address: 10, set data: 02, and press the PAUSE To set to the VTR mode, set the power switch to “VTR”...
Page 159: Adjusting Connectors
3-1-3. Adjusting Connectors Some of the adjusting points of the video section are concentrated at VC-227 board CN2903. Connect the measuring instruments via the CPC-8 jig (J-6082-388-A). The following table lists the pin numbers and signal names of CN2903 Pin No. Signal Name Pin No.
Page 160: Alignment Tapes
3-1-6. Alignment Tapes Use the alignment tapes shown in the following table. Use tapes specified in the signal column of each adjustment. Name Tracking standard (XH2-1) Tape path adjustment SW/OL standard (XH2-3) Switching position adjustment Audio operation check Audio system adjustment (XH5-3 (NTSC), XH5-3P (PAL)) System operation check Operation check...
Page 161: System Control System Adjustment
3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT 2-2. Serial No. Input Write the serial No. and model code in the EEPROM (nonvolatile memory). Convert the serial No. on the name plate from decimal to 1. Initialization of B, C, D, E, F, 7 Page Data hexadecimal, and write in the EEPROM.
Page 162 Hexa- Hexa- Hexa- Hexa- Hexa- Hexa- Hexa- Hexa- Decimal Decimal Decimal Decimal Decimal Decimal Decimal Decimal decimal decimal decimal decimal decimal decimal decimal decimal 0000 8192 2000 16384 4000 24576 6000 32768 8000 40960 A000 49152 C000 57344 E000 0100 8448 2100 16640...
Page 163: Battery End Check (Vc-227 Board)
3. Battery End Check (VC-227 board) Check the battery end voltage. Mode Camera recording Subject Arbitrary Switch setting 1) AUTO FOCUS ..............OFF 2) LCD screen ............OFF (Closed) 3) REC LAMP (Menu display) ..........ON Connection: 1) Connect the regulated power supply and the digital voltmeter to the battery terminal as shown in Fig.
Page 164: Servo And Rf System Adjustment
3-3. SERVO AND RF SYSTEM ADJUSTMENT 2. T reel FG Duty Adjustment (VC-227 board) Adjust the take-up reel FG signal duty cycle to an appropriate value Before perform the servo and RF system adjustments, check that so that the correct T-reel FG signal is obtained. the specified value of “54MHz/66MHz Origin Oscillation Adjustment”...
Page 165: Switching Position Adjustment (Vc-227 Board)
4. Switching Position Adjustment (VC-227 board) 5. AGC Center Level and APC & AEQ Adjustment 5-1. Preparations before adjustments Mode VTR playback Mode Camera recording Signal SW/OL reference tape (XH2-3) Subject Arbitrary Measurement Point Display data of page: 3, address: 03 Measuring Instrument Adjustment remote commander Adjusting method:...
Page 166: Apc & Aeq Adjustment (Vc-227 Board)
5-3. APC & AEQ Adjustment (VC-227 board) 6. PLL f & LPF f Final Adjustment (VC-227 board) Mode Playback Mode VTR stop Signal Recorded signal at “Preparations Signal Arbitrary before adjustments” Measurement Point Display data of page: 3, address: 03 Measurement Point Pin w;...
Page 167: Video System Adjustments
3-4. VIDEO SYSTEM ADJUSTMENTS 2. S VIDEO OUT Y Level Adjustment (VC-227 Board) Before perform the video system adjustments, check that the specified value of “54MHz/66MHz Origin Oscillation Adjustment” Mode Camera of “CAMERA SYSTEM ADJUSTMENT” is satisfied. Subject Arbitrary Measurement Point Y signal terminal of S VIDEO jack Note: The lens block (CD-234 board) must be connected when performing (75Ω...
Page 168: S Video Out Chroma Level Adjustment
3. S VIDEO OUT Chroma Level Adjustment 4. AV OUT Y, Chroma Level Check (VC-227 Board) (VC-227 Board) Mode Camera Mode Camera Subject Arbitrary Subject Arbitrary Measurement Point Chroma signal terminal of S VIDEO Measurement Point Video terminal of AUDIO/VIDEO jack (75Ω...
Page 169: Pll Adjustment (Vc-227 Board)
5. PLL Adjustment (VC-227 Board) Set the VCO center level of the video input circuit (IC1200). Mode VTR stop Signal Color bar (Video terminal of AUDIO/ VIDEO jack input) Measurement Point Display data of page: 3, address: 04 Measuring Instrument Adjustment remote commander Adjustment Page Adjustment Address...
Page 170: Bist Check
3-4-2. BIST Check 1. Playback System Check 1-1. Preparation for Playback When the playback system from IC1600(SFD) to IC2002 Set the POWER switch to VTR position. (ADC&DAC) is normal, the display data (combination data) Connect the adjusting remote commander and set the HOLD of page: 3, address: 14 and 15 agrees with any combination as switch to ON (SERVICE) position.
Page 171: Ic1501(Vfd) Bist(Pb) Check
1-5. IC1501(VFD) BIST(PB) Check • UPY Cb BIST(PB) Check 1) Select page: 0, address: 01, and set data: 01. 20) Select page: 3, address: 10, set data: 8A, and press the PAUSE 2) Select page: C, address: 51, set data: 0F, and press the PAUSE button.
Page 172: Recording System Check
• ENC Ca BIST(PB) Check 2. Recording System Check 35) Select page: 3, address: 10, set data: 8D, and press the PAUSE 2-1. Preparations for recording button. 36) Select page: 3, address: 12, set data: 10, and press the PAUSE Playback the BIST check tape.(XH5-6(NTSC), XH5-6P(PAL)) button.
Page 173: Ic1601(Tfd) Bist(Rec) Check
2-5. IC1900(TRX) BIST(REC) Check 9) Select page: 3, address: 11, set data: 87, and press the PAUSE button. 1) Select page: 3, address: 12, set data: 04, and press the PAUSE 10) Select page: 3, address: 12, set data: 08, and press the PAUSE button.
Page 174: Ir Transmitter Adjustments
3-5. IR TRANSMITTER ADJUSTMENTS 2. IR Video Deviation Adjustment (MR-44 board) Mode VTR stop Adjust using a IR receiver jig (J-6082-383-A). Signal Arbitrary Measurement Point VIDEO OUT terminal of IR receiver jig Switch setting: (Terminated at 75 Ω) LASER LINK ........ON (Red LED is lit) Measuring Instrument Oscilloscope 1.
Page 175: Ir Audio Deviation Adjustment (Mr-44 Board)
3. IR Audio Deviation Adjustment (MR-44 board) Mode VTR stop Signal Video : No signal Audio : –400Hz, –7.5dBs, Audio left and right terminal of AUDIO/VIDEO jack Measurement Point AUDIO L terminal and AUDIO R terminal of IR receiver jig (Terminated at 47kΩ) Measuring Instrument Audio level meter...
Page 176: Audio System Adjustments
3-6. AUDIO SYSTEM ADJUSTMENTS [Connection of Audio System Measuring Devices] Connect the audio system measuring devices as shown in Fig. 5-3-15 Main unit Recording (Camera mode) 600 Ω Left Audio oscillator Right Attenuator 600 Ω : 270 Ω (1-249-410-11) + 330 Ω (1-249-411-11) Playback Main unit TV monitor...
Page 177: Playback Level Check
1. Playback Level Check 4. Overall Noise Level Check Mode VTR playback Mode Camera recording and playback Signal Alignment tape: Signal No signal: Insert a shorting plug in the For audio operation check MIC jack (XH5-3 (NTSC)) Measurement Point Audio left or right terminal of AUDIO (XH5-3P (PAL)) VIDEO jack Measurement Point...
Page 178: Service Mode
5-4. SERVICE MODE 4-1. ADJUSTMENT REMOTE COMMANDER 2. Precautions upon using the adjustment remote commander The adjustment remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The Mishandling of the adjustment remote commander may erase the correct adjustment data at times.
Page 179 4-2. DATA PROCESS The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data.
Page 180: Remote Commander
4-3. SERVICE MODE 2-1. EMG Code (Emergency Code) 1. Setting the Test Mode Codes corresponding to the errors which occur are written in Page D Address 10 addresses 38, 3C and 40. The type of error indicated by the code are shown in the following table.
Page 181: Msw Code
2-2. MSW Code MSW when errors occur: Information on MSW (mode SW) when errors occur MSW when movement starts: Information on MSW when movements starts when the mechanism position is moved (When the L motor is moved) MSW of target of movement: Information on target MSW of movement when the mechanism position is moved Mechanism Position ←...
Page 182: Bit Value Discrimination
3. Bit value discrimination Bit values must be discriminated using the display data of the adjustment remote commander for following items. Use the table below to discriminate if the bit value is “1” or “0”. Display on the adjustment remote commander Address Page bit3 to bit0 discrimination...
Page 183: Switch Check (2)
5. Switch check (2) Page 2 Address 60 to 67 Using method: 1) Select page:2, address: 60 to 67. 2) By discriminating the display data, the pressed key can be discriminated. Data Address 00 (00 to 0A) 19 (0B to 24) 32 (25 to 44) 59 (45 to 6E) 85 (6F to 9F)
Page 184: Repair Parts List
DCR-PC100/PC100E SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • Abbreviation The components identified by mark ! or have some differences from the original one. AUS: Australian model dotted line with mark ! are critical for safety.
Page 185: Cabinet (R) Section-2
6-1-2. CABINET (R) SECTION-2 EVF block assembly (See page 6-5) MIC901 Lens assembly (See page 6-5) supplied not supplied SP901 not supplied not supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-057-482-01 COVER, BATTERY A-7074-105-A MA-367 BOARD,COMPLETE A-7074-106-A FJ-25 BOARD,COMPLETE 1-675-717-11 FP-130 FLEXIBLE BOARD 3-989-735-11 SCREW (M1.7), LOCK ACE, P2...
Page 186: Cabinet (R) Section-3
6-1-3. CABINET (R) SECTION-3 not supplied not supplied supplied ND901 supplied LCD901 - 1 2 a r d Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-989-735-11 SCREW (M1.7), LOCK ACE, P2 3-057-419-01 COVER, DC JACK X-3949-934-1 CABINET (L) ASSY, LCD 3-057-422-01 BASE, LCD LOCK 3-055-797-01 SHEET, BL SHIELD...
Page 187: Cabinet (L) Block Assembly
6-1-4. CABINET (L) BLOCK ASSEMBLY not supplied not supplied supplied supplied supplied supplied supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-989-735-91 SCREW (M1.7), LOCK ACE, P2 X-3949-954-1 CABINET (G) ASSY (100E) X-3949-950-1 CABINET (L) (ASSY-M) * 161 3-057-467-01 BRACKET (REAR), BELT 3-989-735-11 SCREW (M1.7), LOCK ACE, P2...
Page 188: Lens Assembly, Evf Block Assembly
6-1-5. LENS ASSEMBLY, EVF BLOCK ASSEMBLY not supplied not supplied LCD902 not supplied not supplied not supplied LED902 The CCD imager cannot be replaced as an independent part. Replace the entire CD-234 board (including the CCD imager). Ref. No. Part No. Description Remarks Ref.
Page 189: Cassette Compartment And Drum Assy
6-1-6. CASSETTE COMPARTMENT AND DRUM ASSY SECTION FP-242 (See page 6-7) not supplied Attaching procedure not supplied Note M901 Note: Once remove No. 720 CC fastener, don't use it again. Be sure to replace it with new one. (Attaching procedure is as shown above figure.) Ref.
Page 190: Ls Chassis Section
6-1-7. LS CHASSIS SECTION Note 1: About FP-242 and FP-92 The FP-242 and FP-92 flexible boards are installed to a chassis with a hot press, which are included in the Ref. No. 762 chassis (D3) assy, LS block section, They are not supplied separately because the high precision for installation is needed. Note 2: Selecting the T washer Select proper parts for the Ref.
Page 191: Mechanism Chassis Block Section-1
6-1-8. MECHANISM CHASSIS BLOCK SECTION-1 Note: Be sure to remember the installed position (one of two position), direction and thickness of the Ref. No. 820 (spacer, cap) when the M902 (capstan motor )is removed. Refer to “3-9. Capstan motor” on page 15 in the “DV MECHANICAL ADJUSTMENT MANUAL ”...
Page 192: Mechanism Chassis Block Section-2
6-1-9. MECHANISM CHASSIS BLOCK SECTION-2 supplied not supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-3945-640-1 PULLEY ASSY, RELAY 3-748-738-02 GEAR, NO.2 3-315-414-31 WASHER 3-748-741-03 GEAR, NO.1 X-3748-600-1 ARM ASSY, COMPULSION 3-748-731-02 ARM, POSITION X-3748-605-1 CAM(S) ASSY X-3945-639-1 PULLEY ASSY, CONVERSION 3-976-452-01 LEVER, EJECT 3-748-734-01 BELT, RELAY...
Page 193: Electrical Parts List
µF AUS: Australian model Korea model • COILS Tourist model • Model uH: µH CND: Canadian model 100: DCR-PC100 Chinese model 100E: DCR-PC100E Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-7031-039-A CCD/CD BLOCK ASSY(SERVICE USE) (100) <...
Page 194 CD-234 FJ-25 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < VIBRATOR > FB955 1-500-444-11 FERRITE FB956 1-500-444-11 FERRITE X101 1-781-632-21 VIBRATOR, CRYSTAL (66MHz) (100) FB957 1-500-444-11 FERRITE X101 1-781-633-21 VIBRATOR, CRYSTAL (54MHz) (100E) FB990 1-500-444-11 FERRITE ************************************************************ FB992 1-500-444-11 FERRITE...
Page 195 FP-92 FP-242 FP-586 MA-367 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks FP-92 MOUNT (Not supplied) C7313 1-162-970-11 CERAMIC CHIP 0.01uF C7314 1-162-970-11 CERAMIC CHIP 0.01uF *********************** (Ref.No.;4000 Series) C7315 1-164-937-11 CERAMIC CHIP 0.001uF C7316 1-164-937-11 CERAMIC CHIP 0.001uF 3-338-687-41 SCREW (1.4), +P TAPPING (B) C7318...
Page 196 MA-367 MR-44 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < RESISTOR > C1885 1-125-777-11 CERAMIC CHIP 0.1uF C1886 1-125-777-11 CERAMIC CHIP 0.1uF R7303 1-218-990-11 SHORT C1887 1-125-777-11 CERAMIC CHIP 0.1uF R7309 1-218-967-11 RES,CHIP 1/16W C1888 1-164-943-11 CERAMIC CHIP 0.01uF R7310...
Page 197 MR-44 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C7501 1-125-837-91 CERAMIC CHIP 6.3V IC2504 8-759-385-94 IC CXA8053Q-TE-B C7502 1-117-919-11 TANTAL. CHIP 10uF 6.3V IC2505 8-759-434-46 IC TA8486F(EL) C7503 1-164-943-11 CERAMIC CHIP 0.01uF IC7500 8-759-430-57 IC M62367GP-75ED C7504 1-117-919-11 TANTAL.
Page 198 MR-44 PD-125 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R1909 1-218-931-11 RES,CHIP 1/16W R2579 1-218-965-11 RES,CHIP 1/16W R1938 1-218-977-11 RES,CHIP 100K 1/16W R2582 1-218-961-11 RES,CHIP 4.7K 1/16W R1939 1-218-990-11 SHORT R2583 1-218-965-11 RES,CHIP 1/16W R1940 1-218-990-11 SHORT R2585 1-218-959-11 RES,CHIP...
Page 199 PD-125 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C8023 1-164-505-11 CERAMIC CHIP 2.2uF Q8010 8-729-427-74 TRANSISTOR XP4601-TXE C8024 1-164-505-11 CERAMIC CHIP 2.2uF Q8011 8-729-427-74 TRANSISTOR XP4601-TXE C8025 1-107-686-11 TANTAL. CHIP 4.7uF Q8100 8-729-042-59 TRANSISTOR UN9112J-(K8).SO C8026 1-164-943-11 CERAMIC CHIP 0.01uF...
Page 200 PD-125 VC-227 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R8213 1-218-990-11 SHORT C301 1-164-943-11 CERAMIC CHIP 0.01uF R8214 1-218-990-11 SHORT C302 1-125-777-11 CERAMIC CHIP 0.1uF R8215 1-218-941-11 RES,CHIP 1/16W C303 1-127-760-91 CERAMIC CHIP 4.7uF 6.3V R8216 1-218-941-11 RES,CHIP 1/16W...
Page 201 VC-227 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C509 1-125-817-11 CERAMIC CHIP 10uF 6.3V C1228 1-164-850-11 CERAMIC CHIP 18PF C510 1-125-817-11 CERAMIC CHIP 10uF 6.3V C1229 1-164-850-11 CERAMIC CHIP 18PF C512 1-125-817-11 CERAMIC CHIP 10uF 6.3V C1230 1-164-943-11 CERAMIC CHIP...
Page 202 VC-227 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C1623 1-127-760-91 CERAMIC CHIP 4.7uF 6.3V C2245 1-164-943-11 CERAMIC CHIP 0.01uF C2003 1-164-943-11 CERAMIC CHIP 0.01uF C2246 1-164-943-11 CERAMIC CHIP 0.01uF C2004 1-164-943-11 CERAMIC CHIP 0.01uF C2247 1-119-923-81 CERAMIC CHIP 0.047uF C2007...
Page 203 VC-227 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C3247 1-127-895-91 TANTAL. CHIP 22uF D2907 8-719-056-23 DIODE MA2S111-(K8).SO C3248 1-115-566-11 CERAMIC CHIP 4.7uF D3205 8-719-027-76 DIODE 1SS357-TPH3 C3249 1-117-919-11 TANTAL. CHIP 10uF 6.3V D3206 8-719-073-35 DIODE RB551V-30TE-17 C3250 1-127-895-91 TANTAL.
Page 204 VC-227 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks IC1501 8-759-584-66 IC M65511AWG-600D < TRANSISTOR > IC1502 8-759-644-19 IC BU2995-05FV-E2 IC1600 8-759-583-39 IC F722502-TEB Q301 8-729-429-00 TRANSISTOR UN9119J-(K8).SO IC1601 8-752-397-36 IC CXD3129GA-T6 Q401 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO IC1602 8-759-535-43 IC SN104266GGM-TEB Q402...
Page 205 VC-227 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks Q3213 8-729-047-74 TRANSISTOR CPH5701-TL R333 1-218-953-11 RES,CHIP 1/16W Q3214 8-729-047-74 TRANSISTOR CPH5701-TL R334 1-218-953-11 RES,CHIP 1/16W Q3218 8-729-044-58 TRANSISTOR SI2304DS-T1 R335 1-218-973-11 RES,CHIP 1/16W Q3220 8-729-044-58 TRANSISTOR SI2304DS-T1 R336 1-218-973-11 RES,CHIP...
Page 206 VC-227 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R462 1-218-967-11 RES,CHIP 1/16W R783 1-218-977-11 RES,CHIP 100K 1/16W R463 1-218-969-11 RES,CHIP 1/16W R785 1-218-977-11 RES,CHIP 100K 1/16W R464 1-218-985-11 RES,CHIP 470K 1/16W R786 1-218-977-11 RES,CHIP 100K 1/16W R465 1-218-953-11 RES,CHIP...
Page 207 VC-227 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R1430 1-218-953-11 RES,CHIP 1/16W R2021 1-218-965-11 RES,CHIP 1/16W R1432 1-218-965-11 RES,CHIP 1/16W R2022 1-218-965-11 RES,CHIP 1/16W R1433 1-218-953-11 RES,CHIP 1/16W R2023 1-218-953-11 RES,CHIP 1/16W R1434 1-218-965-11 RES,CHIP 1/16W R2024 1-218-953-11 RES,CHIP...
Page 208 VC-227 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R2239 1-218-989-11 METAL CHIP 0.50% 1/16W R2304 1-218-953-11 RES,CHIP 1/16W R2240 1-218-977-11 RES,CHIP 100K 1/16W R2401 1-218-989-11 RES,CHIP 1/16W R2241 1-218-977-11 RES,CHIP 100K 1/16W R2405 1-218-977-11 RES,CHIP 100K 1/16W R2242...
Page 209 VC-227 VF-138 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R3222 1-218-970-11 RES,CHIP 1/16W X2200 1-767-980-21 VIBRATOR, CERAMIC (20MHz) R3223 1-208-713-11 METAL CHIP 0.50% 1/16W X2201 1-767-994-41 VIBRATOR, CRYSTAL (32.768KHz) R3224 1-208-931-11 METAL CHIP 0.50% 1/16W X2400 1-781-044-21 VIBRATOR, CRYSTAL (20MHz) R3225...
Page 210 VF-138 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < COIL > R5503 1-218-964-11 RES,CHIP 8.2K 1/16W R5504 1-218-955-11 RES,CHIP 1.5K 1/16W L5000 1-414-771-91 INDUCTOR CHIP 10uH R5505 1-218-962-11 RES,CHIP 5.6K 1/16W L5001 1-469-058-11 INDUCTOR CHIP 22uH R5506 1-218-957-11 RES,CHIP 2.2K...
Page 211 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks ACCESSORIES & PACKING MATERIALS 3-866-727-11 MANUAL, INSTRUCTION (MSAC-SR1)(PAL) (ENGLISH,RUSSIAN) (100E) ******************************* 3-866-727-21 MANUAL, INSTRUCTION (MSAC-SR1)(PAL) ! FigC 1-418-420-12 ADAPTOR, AC (AC-PW1) (GERMAN,FRENCH) (100E:AEP,E,HK,JE,CN) (100:JE,KR,HK,E/100E:E,HK,JE,AUS,CN) 3-866-727-31 MANUAL, INSTRUCTION (MSAC-SR1)(PAL) ! FigC 1-467-510-42 ADAPTOR, AC (AC-PT1) (100:US,CND) (ITALIAN,DUTCH) (100E:AEP)
Page 212 You can find the parts position of location of mount locations applying to VC-227 board of a set. VC-227 SIDE A DCR-PC100/PC100E IC758 CN2903 〈PARTS REFERENCE SHEET〉 You can find the parts position of location of mount locations applying to MR-44 board of a set.
Page 213 〈 〉 FOR CAMERA COLOR REPRODUCTION ADJUSTMENT For NTSC model Take a copy of CAMERA COLOR DCR-PC100 REPRODUCTION FRAME and Parts referencesheets with a clear sheet for use. For PAL model DCR-PC100E — 267 —...
Page 214 DCR-PC100/PC100E Sony Corporation 99I16055-1 Personal VIDEO Products Company 9-974-191-11 Printed in Japan ©1999.9 — 268 — Published by Safety & Service Engineering Dept.
Page 215 This file has been downloaded from: www.electronica.ro Service Manuals, Schematic Diagram, Repair...

This manual is also suitable for:

Dcr-pc100e

Sony DCR-PC100 Service Manual

Service Note

Self-Diagnosis Function

2 Disassembly

Block Diagrams

Printed Wiring Boards and Schematic Diagrams

Adjustments

Repair Parts List

Quick Links

Related Manuals for Sony DCR-PC100

Summary of Contents for Sony DCR-PC100

This manual is also suitable for:

Table of Contents