Table of Contents
Advertisement
13
Symptom
Remedy
The maximum volume available
Check that the Volume Limit is set to OFF (see
(shown in the front panel display) is
The channel level setting may be over 0.0dB.
lower than the +12dB maximum.
Certain listening modes or
When Operation Mode is set to Basic, the Pioneer-recommended settings are made and
HOME MENU items cannot be
not all of the functions can be used. To use all of the functions without restrictions, set
selected.
Operation Mode to Expert (see
Some functions cannot be selected, depending on the input signal and listening mode.
The volume level drops automati-
The temperature within the unit has exceeded the allowable value. Try moving the unit for
cally.
better ventilation (see
Volume seems different when input
Set the Channel Level setting to ALL, then adjust the volume of the respective input
is switched.
sources (see
Input Volume Absorber
When HDZONE is ON, multi-channel
When HDZONE is selected in Speaker System and also the same HDMI input is selected
audio sources are not output in the
for both the main zone and HDZONE, 2-channel PCM audio sources are output from the
main zone.
main zone as well. To output multi-channel audio sources, set HDZONE to OFF or change
the HDZONE input.
No HDZONE sound is output.
With HDZONE, multi-channel audio may not be output. In this case, set the audio output
setting of your playback device to 2-channel PCM.
BT AUDIO terminal
Symptom
Remedy
The Bluetooth wireless technology
Check that no object that emits electromagnetic waves in the 2.4 GHz band (microwave
device cannot be connected or oper-
oven, wireless LAN device or Bluetooth wireless technology apparatus) is near the unit. If
ated. Sound from the Bluetooth wire-
such an object is near the unit, set the unit far from it. Or, stop using the object emitting
less technology device is not emitted
the electromagnetic waves.
or the sound is interrupted.
Check that the Bluetooth wireless technology device is not too far from the unit and that
obstructions are not set between the Bluetooth wireless technology device and the unit.
Set the Bluetooth wireless technology device and the unit so that the distance between
them is less than about 10 m and no obstructions exist between them.
The Bluetooth wireless technology device may not be set to the communication mode
supporting the Bluetooth wireless technology. Check the setting of the Bluetooth wireless
technology device.
Check that pairing is correct. The pairing setting was deleted from this unit or the Blue-
tooth wireless technology device. Reset the pairing.
Check that the profile is correct. Use a Bluetooth wireless technology device that sup-
ports A2DP profile and AVRCP profile.
Volume Setup
on
page 107
).
Operation Mode Setup
on
page 51
).
Installing the receiver
on
page 10
).
on
page 83
).
Video
Symptom
Remedy
No image is output when an input is
Check the video connections of the source component.
selected.
For HDMI, or when V.CONV is set to OFF and a TV and another component are con-
nected with different cords (in
your TV to this receiver using the same type of video cable as you used to connect your
video component. For the component video input, however, signals are only output from
the HDMI OUT 1 or HDMI OUT 2 terminal, so when using the component video input,
set V.CONV to OFF.
Make sure the input assignment is correct for components connected using component
video or HDMI cables (see
Check the video output settings of the source component.
Check that the video input you selected on your TV is correct.
Some components (such as video game units) have resolutions that may not be con-
verted. If adjusting this receiver's Resolution setting (in
page 80
) and/or the resolution settings on your component or display doesn't work, try
switching V.CONV (in
When the device is connected using an HDMI OUT terminal, press the remote con-
trol's OUT P. button to check the HDMI OUT output setting. For OUT 3, also check the
MAIN/HDZONE setting at ZONE Setup.
When the HDMI OUT 1/2 setting of the output parameter function is set to OFF, set it to
ON.
If HDZONE is set to on, video images connected using a video cable or component cable
are not output from the HDMI terminal. To output video images, turn HDZONE off
84
).
Noisy, intermittent, or distorted
Sometimes a video deck may output a noisy video signal (during scanning, for example),
picture.
or the video quality may just be poor (with some video game units, for example). The
picture quality may also depend on the settings, etc. of your display device. Switch off
the video converter and reconnect the source and display device using the same type of
connection (component or composite), then start playback again.
Video signals are not output from the
When a monitor only compatible with resolutions of 480i is connected to the component
component terminal.
terminal and another monitor is connected to the HDMI terminal, the video signals may
not be output to the monitor connected to the component terminal. If this happens, do
the following:
— Turn off the power of the monitor connected to the HDMI terminal.
— Change the VIDEO P. menu RES setting (see
— Video signals from the HDMI terminal cannot be output to the component terminals.
Input the video signals from the player or other source to the composite or component
terminals. When using the component terminal, assign it at Input Setup (see
Setup menu
The picture's movement is unnatu-
When Resolution under VIDEO PARAMETER is set to 1080/24p or 4K/24p, the picture
ral.
may not be displayed properly for some source materials. In this case, set the resolution
to something other than 1080/24p or 4K/24p
Video parameters cannot be used.
For audio only input (TUNER, CD, and TV), the video parameter function cannot be used.
Use for video or input with a GUI display.
Cannot be used when the HDZONE is ON. Turn OFF the HDZONE.
115
Setting the Video options
on
page 80
), you must connect
The Input Setup menu
on
page 50
).
Setting the Video options
Setting the Video options
on
page 80
) to OFF.
Setting the Video options
on
page 50
).
(page 80
).
FAQ
on
(page
on
page 80
).
The Input
Advertisement
Table of Contents
