hit counter script
Sony HCD-EX5 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Stereo System
  5. HCD-EX5 - Micro Hi-fi Component System
  6. Service manual
Sony HCD-EX5 Service Manual

Sony HCD-EX5 Service Manual

Hide thumbs Also See for HCD-EX5:
Table of Contents

Advertisement

Quick Links

QQ
3 7 63 1515 0
SERVICE MANUAL
Ver. 1.2 2007. 02
This set is the tuner, CD and amplifier
section in CMT-EX5
Amplifier section
TE
L 13942296513
For the U.S. model
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 4 ohms loads, both channels driven, from
120 - 10,000 Hz; rated 12 watts per channel
minimum RMS power, with no more than 10%
total harmonic distortion from 250 milli watts
to rated output.
North American model:
Continuous RMS power output (Reference):
European model:
DIN power output (Rated): 12 + 12 W
Continuous RMS power output (Reference):
Music power output (Reference):
Other models:
The following measured at 220 V AC, 60 Hz
DIN power output (Rated):
Continuous RMS power output (Reference):
www
.
Sony Corporation
9-874-036-03
2007B16-1
Personal Audio Division
© 2007.02
Published by Sony Techno Create Corporation
http://www.xiaoyu163.com
Inputs
PC/TAPE/MD IN (stereo mini jack):
Outputs
PC/TAPE/MD OUT (stereo mini jack):
PHONES (stereo mini jack):
OPTICAL CD DIGITAL OUT (Supported sampling
frequency: 44.1 kHz)
15 + 15 W
CD player section
(4 ohms at 1 kHz, 10%
THD)
System
Laser
(4 ohms at 1 kHz, DIN)
15 + 15 W
(4 ohms at 1 kHz, 10%
Frequency response
THD)
Tuner section
15 + 15 W
FM stereo, FM/AM superheterodyne tuner
12 + 12 W
(4 ohms at 1 kHz, DIN,
110 V – 240 V AC)
15 + 15 W
(4 ohms at 1 kHz, 10%
THD, 110 V – 240 V AC)
x
ao
u163
y
i
http://www.xiaoyu163.com
HCD-EX5
2 9
8
Model Name Using Similar Mechanism
CD
CD Mechanism Type
SECTION
Base Unit Type
SPECIFICATIONS
Q Q
3
6 7
1 3
1 5
voltage 450 mV (MD)/
250 mV (PC/TAPE),
impedance 47 kilohms
voltage 250 mV,
impedance 1 kilohm
accepts headphones with
an impedance of 8 ohms
or more
Compact disc and digital
audio system
Semiconductor laser
(λ = 795 nm)
Emission duration:
continuous
2 Hz – 20 kHz
MICRO Hi-Fi COMPONENT SYSTEM
co
.
9 4
2 8
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Chinese Model
NEW
CDM71C-31BD63A
BU-31BD63A
FM tuner section
0 5
8
2 9
9 4
2 8
Tuning range
North American model:
87.5 – 108.0 MHz
(100-kHz step)
Other models:
87.5 – 108.0 MHz
(50-kHz step)
Antenna
FM wire antenna
Antenna terminals
75 ohms unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
Pan-American model:
530 – 1,710 kHz
(with the interval set at
10 kHz)
531 – 1,710 kHz
(with the interval set at
9 kHz)
European model:
531 – 1,602 kHz
(with the interval set at
9 kHz)
Other models:
530 – 1,710 kHz
(with the interval set at
10 kHz)
531 – 1,602 kHz
(with the interval set at
9 kHz)
Antenna
AM loop antenna, external
antenna terminal
Intermediate frequency
450 kHz
— Continued on next page —
m
9 9
9 9

Advertisement

Table of Contents
loading

Related Manuals for Sony HCD-EX5

Summary of Contents for Sony HCD-EX5

  • Page 1 Continuous RMS power output (Reference): 15 + 15 W (4 ohms at 1 kHz, 10% THD, 110 V – 240 V AC) MICRO Hi-Fi COMPONENT SYSTEM u163 Sony Corporation 9-874-036-03 2007B16-1 Personal Audio Division © 2007.02 Published by Sony Techno Create Corporation http://www.xiaoyu163.com...
  • Page 2 HCD-EX5 3 7 63 1515 0 SAFETY CHECK-OUT General Power requirements North American model: 120 V AC, 60 Hz After correcting the original service problem, perform the European model: 230 V AC, 50/60 Hz following safety checks before releasing the set to the customer:...

  • Page 3: Table Of Contents

    HCD-EX5 3 7 63 1515 0 TABLE OF CONTENTS 1. SERVICING NOTES 6. DIAGRAMS ······················································· 4 ······································································ 25 6-1. Block Diagrams ··························································· 25 2. GENERAL 6-2. Circuit Boards Location ·············································· 28 ·········································································· 5 6-3. Schematic Diagram – BD Board – ······························ 29 6-4.

  • Page 4: Servicing Notes

    30 cm away from the objective lens. DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY Laser component in this product is capable DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU of emitting radiation exceeding the limit for DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

  • Page 5: General

    HCD-EX5 SECTION 2 This section is extracted GENERAL 3 7 63 1515 0 from instruction manual. Main unit ALPHABETICAL ORDER BUTTON DESCRIPTIONS @/1 (power) 1 R – Z A – Q Remote sensor qs Disc slot 2 (23) ./> 6...
  • Page 6 HCD-EX5 3 7 63 1515 0 Remote control ALPHABETICAL ORDER BUTTON DESCRIPTIONS L – Z A – K @/1 (power) 4 Letter/Number buttons wf (10, BASS +/– qj (17) ./> qa 12, 15) CD N ws (9 - 11, 23) +/–...

  • Page 7: Http://Www.xiaoyu163.Com

    HCD-EX5 3 7 63 1515 0 Replacing the battery in Setting the clock the remote Turn on the system. Press CLOCK/TIMER SET on the Slide out and remove the battery case. remote. The day indication flashes. Press . or > on the remote repeatedly to set the day, then press ENTER/YES on the remote.

  • Page 8: Disassembly

    HCD-EX5 SECTION 3 DISASSEMBLY 3 7 63 1515 0 • The equipment can be removed using the following procedure. SET (HCD-EX5) CASE OC BOARD,OS BOARD GLASS WINDOW ASSY (U) BD BOARD POWER BOARD CASE BUTTON ASSY,LID BOARD MAIN BOARD,TUNNER...

  • Page 9: Case

    HCD-EX5 3 7 63 1515 0 Note : Follow the disassembly procedure in the numerical order given. 3-1. Case 7 case 6 c onnector (CN621) 1 cover (back) 4 four screws (+BVTP 3 × 8 ) 3 cover (bottom) 2 six screws (+BVTP 3 ×...

  • Page 10: Glass Window Assy (U)

    HCD-EX5 3 7 63 1515 0 3-3. Glass Window Assy (U) 4 retainer plate (L) 3 t hree screws (+BVTP 3 × 8 ) 1 t hree screws (+BVTP 3 × 8 ) 7 glass window assy (U) 6 four bushings (bracket)

  • Page 11: Bd Board

    HCD-EX5 3 7 63 1515 0 3-5. BD Board 1 f lat type wire (23 core) Remove solder (two portions ). 7 BD board (BLK) (RED) 4 screw (+B 2 × 4 ) 6 flxible board 5 h ook Remove solder (two portions ).

  • Page 12: Cd Mechanism (Cdm71C-31Bd63A)

    HCD-EX5 3 7 63 1515 0 3-7. CD Mechanism (CDM71C-31BD63A) 7 CD mechanism (CDM71C-31BD63A) 6 four screws (+BVTP 3 × 8 ) 3 f lat type wire (23 core) 4 connector (CN302) 5 connector (CN303) 1 two screws (+BVTP 3 × 8 )

  • Page 13: Holder Assy, Sled Motor Assy (M102)

    HCD-EX5 3 7 63 1515 0 3-9. Holder Assy, Sled Motor Assy (M102) 8 screw (+PTPWH M2.6) 9 two screws (+PTPWH M2.6) q; h ook qa base unit 4 flxible board qd sled motor assy (M102) qs screw (+P 2 × 3)

  • Page 14: Lid (Cd)

    HCD-EX5 3 7 63 1515 0 3-11. LID (CD) 4 three screws (+BVTT 2.6 × 4 ) 6 LID (CD) 2 three screws (+BVTT 2.6 × 4 ) 5 retainer plate (L) 1 tension coil spring (CD door) 3 retainer plate (R) L 13942296513 3-12.

  • Page 15: L.motor Board

    HCD-EX5 3 7 63 1515 0 3-13. L.MOTOR Board Remove solder (two portions ). 2 two screws (+BVTP 2.6 × 8) 4 L.MOTOR board 3 connector (CN711) L 13942296513 3-14. C MOTOR Board, L.SENSOR Board 3 connector (CN711) 4 c onnector...

  • Page 16: Encoder Board, D.sensor Board

    HCD-EX5 Ver 1.1 2003.12 3 7 63 1515 0 3-15. ENCODER Board, D.SENSOR Board 6 screw 7 D.SENSOR board (+BTP 2.6 × 6) 2 screw (+BTP 2.6 × 8 ) 4 screw (+PWH 2 × 6) 1 screw (+BTP 2.6 × 6)

  • Page 17: Rtr Pulley Assy, Rtl Pulley Assy, Belt (Cdm71), Belt (Roller) (L)

    HCD-EX5 3 7 63 1515 0 3-16. RTR Pulley Assy, RTL Pulley Assy, Belt (CDM71), Belt (Roller) (L) 6 screw (+BTP 2.6 × 6) 7 D.SENSOR board 2 screw (+BTP 2.6 × 8 ) 3 cover (encoder) 1 screw (+BTP 2.6 ×...
  • Page 18 HCD-EX5 3 7 63 1515 0 PRECAUTION DURING PULLEY (RTR) ASSY, PULLEY (RTL) ASSY INSTALLATION pulley (RTR) assy pulley (RTR) assy marks of the gear (S2) gear (S2) (9 o'clock position) Place the holes of the gear (S2) at the 9 o'clock position and install the pulley (RTR) assy.

  • Page 19: Spt Pulley Assy, Gear (Rt) Assy, Gear (Kt)

    HCD-EX5 3 7 63 1515 0 3-17. SPT Pulley Assy, Gear (RT) Assy, Gear (KT), Belt (CDM71) Rotate the SPT pulley assy in the direction of , and remove your hands at the position where the shaft agrees with the hole shape on the chassis.
  • Page 20 HCD-EX5 3 7 63 1515 0 PRECAUTION DURING gear (RT) assy, gear (KT) INSTALLATION lever (ST) The boss that is closest to the inside cam (A) pulley (LDG2) gear (KT) Rotate the pulley (LDG2) until it reaches the position Install the gear (KT) and position it so that the boss where the cam (A) contacts with the lever (ST).

  • Page 21: Test Mode

    HCD-EX5 SECTION 4 TEST MODE 3 7 63 1515 0 [Key Check Mode] [Amp Test Mode] * Keyboard check. * Volume level is changed for the amplifier test. Procedure: Procedure: Press the ?/1 button to turn the set ON.
  • Page 22 HCD-EX5 3 7 63 1515 0 [Aging In Mode] [Error History Display Mode] Procedure: Procedure: Press the ?/1 button to turn the set ON. Setting Method of Test Mode Select the FUNCTION to CD. Press the ?/1 button to turn the set ON.
  • Page 23 HCD-EX5 3 7 63 1515 0 DISPLAY : “ E**M##%%0000 “ Reset of No Disc Error History Select the operation in the menu by pressing the . or > : order of mechanism error happens (hexadecimal) 00 : the newest error button to display “dvt ECONT0 BU”.

  • Page 24: Electrical Adjustments

    HCD-EX5 SECTION 5 ELECTRICAL ADJUSTMENTS 3 7 63 1515 0 Adjustment Location : CD SECTION Note : [ BD BOARD ] — SIDE A — 1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given.

  • Page 25: Diagrams

    HCD-EX5 SECTION 6 DIAGRAMS 3 7 6 3 1 5 1 5 0 6-1. Block Diagrams – CD Section – IC381 OSCILLATOR • R-CH is omitted due to same as L-CH. • Signal Path X381 : CD DIGITAL OUT 16.934MHz...
  • Page 26 HCD-EX5 – MAIN Section – 3 7 6 3 1 5 1 5 0 IC121 PRE AMP J111 R-CH INEX1 PC/MD/TAPE IC101 MUTING Q111 DIGITAL POWER AMP J101 R-CH PC/MD/TAPE INB1 OUT1 IN1 L-IN MUTING Q122 OUTM1 FAULT (-)L-...
  • Page 27 HCD-EX5 3 7 63 1515 0 THIS NOTE IS COMMON FOR PRINTED WIRING For printed wiring boards. BOARDS AND SCHEMATIC DIAGRAMS. Note: • X : parts extracted from the component side. (In addition to this, the necessary note is printed •...

  • Page 28: Circuit Boards Location

    HCD-EX5 3 7 63 1515 0 6-2. Circuit Boards Location POWER board OS board OC board SPK board LED board MAIN board LID board L 13942296513 BD board L.MOTOR board ENCODER board D.SENSOR board C MOTOR board tuner L.SENSOR board u163 http://www.xiaoyu163.com...

  • Page 29: Schematic Diagram - Bd Board

    HCD-EX5 6-3. Schematic Diagram – BD Board – • See page 45 for IC Block Diagrams. • See page 46 for Wavefoms. 3 7 6 3 1 5 1 5 0 IC B/D IC B/D 1 3 9 4 2 2 9 6 5 1 3...

  • Page 30: Printed Wiring Board - Bd Board (Side A)

    HCD-EX5 6-4. Printed Wiring Board – BD Board (Side A) – • See page 28 for Circuit Boards Location. 3 7 6 3 1 5 1 5 0 R 2 2 6 C N 1 0 1 IC106 R 2 3 7...

  • Page 31: Printed Wiring Board - Bd Board (Side B)

    HCD-EX5 6-5. Printed Wiring Board – BD Board (Side B) – • See page 28 for Circuit Boards Location. 3 7 6 3 1 5 1 5 0 R 2 1 5 R 1 9 0 R 2 1 4...

  • Page 32: Schematic Diagram - Main Section (1/2)

    HCD-EX5 6-6. Schematic Diagram – MAIN Section (1/2) – • See page 46 for IC Block Diagrams. • See page 46 for Wavefoms. 3 7 6 3 1 5 1 5 0 R384 IC B/D C381 1 3 9 4 2 2 9 6 5 1 3...

  • Page 33: Schematic Diagram - Main Section (2/2)

    HCD-EX5 6-7. Schematic Diagram – MAIN Section (2/2) – • See page 43 for IC Pin Function Description. • See page 46 for Wavefoms. 3 7 6 3 1 5 1 5 0 (Page 38) (Page 38) (Page 29)

  • Page 34: Printed Wiring Board - Main Board (Side A)

    HCD-EX5 6-8. Printed Wiring Board – MAIN Board (Side A) – • See page 28 for Circuit Boards Location. 3 7 6 3 1 5 1 5 0 J101 J111 J501 IC371 CD DIGITAL • Semiconductor OPTICAL Location IC371 ETP101 Ref.

  • Page 35: Printed Wiring Board - Main Board (Side B)

    HCD-EX5 6-9. Printed Wiring Board – MAIN Board (Side B) – • See page 28 for Circuit Boards Location. 3 7 6 3 1 5 1 5 0 1 3 9 4 2 2 9 6 5 1 3...

  • Page 36: Printed Wiring Board - Panel Section (Side A)

    HCD-EX5 6-10. Printed Wiring Board – PANEL Section (Side A) – • See page 28 for Circuit Boards Location. 3 7 6 3 1 5 1 5 0 JW896 JW895 R822 RY891 C826 JW894 R872 C876 C874 JW893 C824...

  • Page 37: Printed Wiring Board - Panel Section (Side B)

    HCD-EX5 6-11. Printed Wiring Board – PANEL Section (Side B) – • See page 28 for Circuit Boards Location. 3 7 6 3 1 5 1 5 0 1 3 9 4 2 2 9 6 5 1 3...

  • Page 38: Schematic Diagram - Motor Section

    HCD-EX5 6-12. Schematic Diagram – MOTOR Section – • See page 45 for IC Block Diagrams. 3 7 6 3 1 5 1 5 0 MAIN BOARD (2/2) CN302 (Page 33) MAIN BOARD (2/2) CN303 (Page 33) 1 3 9 4 2 2 9 6 5 1 3...

  • Page 39: Printed Wiring Board - Motor Section

    HCD-EX5 6-13. Printed Wiring Board – MOTOR Section – • See page 28 for Circuit Boards Location. 3 7 6 3 1 5 1 5 0 IC721 CN721 R721 C701 JW703 R722 JW702 IC701 R701 JW701 R702 D701 C751...

  • Page 40: Printed Wiring Board - Power Board (Side A)

    HCD-EX5 6-14. Printed Wiring Board – POWER Board (Side A) – • See page 28 for Circuit Boards Location. 3 7 6 3 1 5 1 5 0 R 9 0 1 L 9 0 1 R 8 9 7...

  • Page 41: Printed Wiring Board - Power Board (Side B)

    HCD-EX5 6-15. Printed Wiring Board – POWER Board (Side B) – • See page 28 for Circuit Boards Location. 3 7 6 3 1 5 1 5 0 1 3 9 4 2 2 9 6 5 1 3...

  • Page 42: Schematic Diagram - Power Section

    HCD-EX5 6-16. Schematic Diagram – POWER Section – 3 7 6 3 1 5 1 5 0 C826 EPT801 R822 C876 R872 1 3 9 4 2 2 9 6 5 1 3 AUS,SP,MX,HK,TW,KR FB801 PC51 (Page 33) w w w u 1 6 3 http://www.xiaoyu163.com...

  • Page 43: Ic Pin Function Description

    HCD-EX5 3 7 63 1515 0 6-17. IC Pin Function Description µPD703030BYGF-M02-3BA Master Controller (Main Board) • IC701 Pin No. Pin Name Description DISP_DATA Data output to the LCD601 DISP_CLK Clock output to the LCD601 IIC DATA IIC data input/output (fixed at “H”)
  • Page 44 HCD-EX5 3 7 63 1515 0 Pin No. Pin Name Description DEVICE RESET Device reset signal output (open) DEVICE ACCUT Device AC cut signal output (open) DACDATA Data output to the DAC (IC301) DACCLK Clock output to the DAC (IC301)
  • Page 45 HCD-EX5 3 7 63 1515 0 • IC Block Diagrams – BD BOARD – IC101 CXD3068Q IC103 CXA2581N-T4 RW/ROM DC OFST RFDCI – – RFDCO – RW/ROM VOFST APC AMP EQ ON/OFF RFAC EQ IN RW/ROM RFAC AC SUM...
  • Page 46 HCD-EX5 3 7 63 1515 0 – MAIN BOARD – IC301 PCM1748E/2K System Clock System Clock MCLK Manager Serial Input DATA 8x Oversampling Digital Filter LRCK with Function Controller Function Control DGND Power DATA Supply Enhanced Multi-Level Deita-Sigma Modurator...

  • Page 47: Exploded Views

    HCD-EX5 SECTION 7 EXPLODED VIEWS 3 7 63 1515 0 NOTE: • -XX, -X mean standardized parts, so they may • Abbreviation The components identified by mark 0 or have some differences from the original one. : Mexican model.

  • Page 48: Chassis Section-1

    HCD-EX5 3 7 63 1515 0 7-2. Chassis Section-1 supplied supplied F801 supplied supplied L 13942296513 CD mechanism section (CDM71C-31BD63A) chassis section-2 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-4954-720-1 PANEL ASSY, FRONT * 55...

  • Page 49: Chassis Section-2

    HCD-EX5 3 7 63 1515 0 7-3. Chassis Section-2 supplied LCD601 supplied supplied L 13942296513 supplied supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-4954-716-1 WINDOW ASSY (L), GLASS 1-769-940-11 WIRE (FLAT TYPE) (11 CORE) (EXCEPT AEP,UK)

  • Page 50: Mechanism Section(Cdm71C-31Bd63A)-1

    HCD-EX5 3 7 63 1515 0 7-4. Mechanism Section(CDM71C-31BD63A)-1 mechanism section M701 (CDM71C-31BD63A)-2 supplied M702 supplied not supplied L 13942296513 supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 4-240-317-01 SPRING (CD DOOR), TENSION COIL...

  • Page 51: Mechanism Section(Cdm71C-31Bd63A)-2

    HCD-EX5 3 7 63 1515 0 7-5. Mechanism Section(CDM71C-31BD63A)-2 supplied L 13942296513 supplied base unit (BU-31BD63A) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-4954-292-1 PULLEY (SPT) ASSY 4-218-252-51 SCREW (+PTPWH M2.6), FLOATING 4-237-417-02 CAM (A)

  • Page 52: Base Unit (Bu-31Bd63A)

    HCD-EX5 Ver. 1.2 3 7 63 1515 0 7-6. Base Unit (BU-31BD63A) not supplied not supplied not supplied M101 (including Ref. No. 516) M102 L 13942296513 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 4-218-252-51 SCREW (+PTPWH M2.6), FLOATING...

  • Page 53: Electrical Parts List

    HCD-EX5 SECTION 8 ELECTRICAL PARTS LIST 3 7 63 1515 0 NOTE: • Due to standardization, replacements in the • CAPACITORS: uF: µF When indicating parts by reference number, parts list may be different from the parts please include the board name.
  • Page 54 HCD-EX5 D.SENDOR ENCODER C MOTOR 3 7 63 1515 0 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R151 1-216-845-11 METAL CHIP 100K 1/16W * CN754 1-568-954-11 PIN, CONNECTOR 5P R152 1-216-829-11 METAL CHIP 4.7K...
  • Page 55 HCD-EX5 L.MOTOR L.SENSOR MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R603 1-216-825-11 METAL CHIP 2.2K 1/16W A-4729-141-A MAIN BOARD, COMPLETE (MX) R611 1-216-821-11 METAL CHIP 1/16W A-4676-648-A MAIN BOARD, COMPLETE (AUS,SP,HK,TW,KR)
  • Page 56 HCD-EX5 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C351 1-162-965-11 CERAMIC CHIP 0.0015uF 10% C798 1-164-159-21 CERAMIC 0.1uF C352 1-162-927-11 CERAMIC CHIP 100PF C799 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V...
  • Page 57 HCD-EX5 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < LIQUID CRYSTAL DISPLAY > R176 1-216-841-11 METAL CHIP 1/16W R177 1-216-825-11 METAL CHIP 2.2K 1/16W LCD601 1-804-713-11 DISPLAY PANEL, LIQUID CRYSTAL...
  • Page 58 HCD-EX5 MAIN POWER 3 7 63 1515 0 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R697 1-216-809-11 METAL CHIP 1/16W R765 1-216-833-11 METAL CHIP 1/16W R767 1-216-833-11 METAL CHIP 1/16W R701 1-216-825-11 METAL CHIP 2.2K...
  • Page 59 HCD-EX5 POWER 3 7 63 1515 0 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 1-131-714-11 ELECT 100uF 400V (AEP,UK) C882 1-115-467-11 CERAMIC CHIP 0.22uF 10.00% 10V 1-107-908-11 ELECT 33uF 20.00% 50V C883 1-107-826-11 CERAMIC CHIP 0.1uF...
  • Page 60 HCD-EX5 POWER 3 7 63 1515 0 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < EARTH > < RESISTOR > * EPT1 1-537-738-21 TERMINAL, EARTH 0 R1 1-219-237-11 SOLID 3.3M 1/2W * EPT2 1-537-738-21 TERMINAL, EARTH (US,CND)
  • Page 61 HCD-EX5 Ver. 1.2 POWER 3 7 63 1515 0 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R944 1-216-821-11 METAL CHIP 1/16W MISCELLANEOUS R951 1-249-417-11 CARBON 1/4W F ************** R952 1-216-833-11 METAL CHIP 1/16W R955...
  • Page 62 HCD-EX5 3 7 63 1515 0 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page.

Table of Contents