Page 1
CDP-M7 SERVICE MANUAL US Model Canadian Model E Model Tourist Model CDP-M7 is the CD player section in DHC-MD7. Model Name Using Similar Mechanism CD Mechanism Type CDM38A-5BD19 Base Unit Type BU-5BD19 Optical Pick-up Type KSS-213B/K-N SPECIFICATIONS Design and specifications are subject to change without notice.
MODEL IDENTIFICATION TABLE OF CONTENTS — BACK PANEL — 1. SERVICING NOTE ............2. GENERAL ..............Parts No. 3. DISASSEMBLY 3-1. Case, Front Panel Assembly and Chassis ......7 PARTS No. 3-2. Back Panel and Tray ............7 US,Canadian model 4-977-697-2π...
Page 3
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE REPLACE THESE COMPONENTS WITH SONY PARTS FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. DONNÉS DANS...
Page 4
SECTION 1 SERVICE NOTE NOTES ON LASER DIODE EMISSION CHECK NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up The laser diode in the optical pick-up block may suffer electrostatic block.
Page 5
If the other units are not available, use a service box (PFJ-1) and jig (J-2501-078-A). In this case, press the p button and TIME button and §OPEN/CLOSE button simultaneously to turn on the power. [Connection Diagram] SERVICE BOX (PFJ-1) UNIT (CDP-M7) (J-2501-078-A) POWER SW FH-E939,838,937...
SECTION 4 ELECTRICAL ADJUSTMENTS Note: S Curve Check 1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. oscilloscope 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. BD board 3. Use an oscilloscope with more than 10M impedance. 4.
Page 10
E-F Balance Check Adjustment Location [BD BOARD] — Component Side — oscilloscope BD board TP (TEO) RV101 TP (VC) IC101 Procedure: RV103 1. Connect a lead wire to the test point TP501 on Display board. 2. Connect oscilloscpe to test point TP (TEO) on BD board. 3.
5-2. IC PIN FUNCTION • IC501 SYSTEM CONTROL (µPD780205GF-016-3BA) Function Pin No. Pin Name – Power supply. (+5V) PWMSW Pulse width modulation select switch for turn table. (Not used) DISC SENS Slit sensor input of disc table. “L”: None , “H”: Load TABLE R Table motor control signal output.
Page 13
Pin No. Pin Name Function LED JOG LED drive signal output. LED ENT Disctray address detect encoder input. 43 to 45 E3 to E1 Power supply (+5V) – 47 to 49 LED DP3 to LED DP1 LED drive signal output. 50 to 52 DE3 to DE1 53 to 78...
6-4. BASE UNIT SECTION (BU-5BD19) M101 (including M102 r A) S101 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiques pour la sécurité.
SECTION 7 ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in the parts • CAPACITORS The components identified by mark list may be different from the parts specified in the uF : µ F ! or dotted line with mark ! are diagrams or the components used on the set.
Page 26
DISPLAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < VIBRATOR > R116 1-216-061-00 METAL CHIP 3.3K 1/10W R117 1-216-069-00 METAL CHIP 6.8K 1/10W X101 1-579-280-11 VIBRATOR, CRYSTAL (16.9344MHz) R118 1-216-049-91 METAL GLAZE 1/10W R119 1-216-089-91 METAL GLAZE 1/10W ************************************************************ R120...
Page 27
DISPLAY MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R514 1-249-417-11 CARBON 1/4W F R582 1-249-441-11 CARBON 100K 1/4W R515 1-247-834-11 CARBON 1.3K 1/4W R583 1-249-441-11 CARBON 100K 1/4W R516 1-249-421-11 CARBON 2.2K 1/4W F R521 1-249-423-11 CARBON 3.3K...