Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
Advertisement
Table of Contents
Related Manuals for Toro 38026
Summary of Contents for Toro 38026
- Page 1 Form No. 3350-232 Rev B ® 1800 Power Curve Snowthrower Model No. 38026—24000001 and Up Operator’s Manual Original Instructions (EN)
-
Page 2: Table Of Contents
Contents Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and Page serial numbers of your product ready. Figure 1 illustrates the location of the model and serial numbers on the Introduction . -
Page 3: Safety
Never operate the snowthrower without proper • motor is running, except where specifically guards, plates, or other safety protective devices in recommended by Toro. place. Let the motor and the snowthrower adjust to the • Never operate the snowthrower near glass enclosures, outdoor temperature before starting to clear snow. -
Page 4: Toro Snowthrower Safety
, based on measurements of identical machines per Directive 98/37/EC. Toro Snowthrower Safety The following list contains safety information specific to Toro products or other safety information that you must know. Rotating rotor blades can injure fingers or hands. •... -
Page 5: Safety And Instruction Decals
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 107-3040 1. Cutting dismemberment, impeller and cutting dismemberment, auger hazards—keep bystanders a safe distance from the snowthrower. -
Page 6: Setup
Setup 6. Place the mounting plate over the tubes (Fig. 3). Note: Determine the left and right hand sides of the snowthrower by standing in the normal operating position. Installing the Upper Handle and Chute Crank 1. Stand the snowthrower on its wheels and position the upper handle. -
Page 7: Installing The Discharge Chute
Before Starting Installing the Discharge Chute 1. Position the chute deflector onto the discharge chute For safe and efficient use of your appliance, use only an and align the mounting holes (Fig. 5). extension cord recommended for outdoor use. Use only a 2.5 mm extension cord up to 25 m long. -
Page 8: Operation
Operation • To adjust the discharge chute, rotate the chute crank clockwise to move the discharge chute to the left; counterclockwise to move it to the right. Check the condition of the snowthrower before operating Note: The chute crank makes a noise as you turn the it to ensure that the rotor turns freely. -
Page 9: Maintenance
• To shave down large banks of snow, lift the • When operating the snowthrower, keep the wheels snowthrower by the primary and secondary handles 1 inch (2.5 cm) off the pavement by tipping the (Fig. 9) and place the snowthrower on the bank. Let snowthrower forward. -
Page 10: Replacing The Scraper
Replacing the Scraper 2. Use a 5/16-inch Allen wrench to turn the rotor shaft clockwise (left-hand thread) while holding the rotor (Fig. 12). The scraper is located at the bottom of the rotor housing as shown in Figure 10. 1538 Figure 12 1517 1. -
Page 11: Replacing The Large Belt
6. Align the left side of the new rotor with the coupler. 3. Remove the idler spring from the idler arm (Fig. 16). Note: The 3 bosses on the rotor end must align with the slots on the coupler (Fig. 15). 1526 Figure 16 1. -
Page 12: Replacing The Small Belt
7. Rotate the rotor with your left hand while sliding the 7. Slide 2 washers onto the bolt and insert the bolt belt onto the large pulley with your right hand through the small pulley. (Fig. 19). Note: The bolt must ride on bearings in the small pulley.