hit counter script
Sony CDX-M700R Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Car Receiver
  5. CDX-M700R
  6. Service manual

Sony CDX-M700R Service Manual

Hide thumbs Also See for CDX-M700R:
Table of Contents

Advertisement

Quick Links

CDX-M700R/M750
SERVICE MANUAL
Ver 1.2 2001. 03
• The tuner and CD sections have no adjustments.
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS (CDX-M750)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
19 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 1% total harmonic distortion.
Other Specifications
CD player section
System
Compact disc digital audio
system
Signal-to-noise ratio
90 dB
Frequency response
10 – 20,000 Hz
Wow and flutter
Below measurable limit
Laser Diode Properties (CDX-M750)
Material
GaAlAs
Wavelength
780 nm
Emission Duration
Continuous
Laser output power
Less than 44.6 µW*
* This output is the value measured at a distance
of 200 mm from the objective lens surface on the
Optical Pick-up Block.
Tuner section
FM
Tuning range
87.5 – 107.9 MHz (CDX-M750)
87.5 – 108.0 MHz (CDX-M700R)
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
8 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
66 dB (stereo),
72 dB (mono)
Harmonic distortion at 1 kHz
0.6% (stereo),
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
AM (CDX-M750)
Tuning range
530 – 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
30 µV
Sony Corporation
9-870-134-12
2001C0400-1
Audio Entertainment Group
© 2001. 3
General Engineering Dept.
Photo: CDX-M750
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
MW/LW (CDX-M700R)
Tuning range
Aerial terminal
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
Power amplifier section
Outputs
Speaker impedance
Maximum power output 50 W × 4 (at 4 ohms)
General
Outputs
Inputs
Power requirements
FM/AM COMPACT DISC PLAYER
FM/MW/LW COMPACT DISC PLAYER
US Model
Canadian Model
AEP Model
UK Model
NEW
MG-383V-121//K
KSS-720A
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
External aerial connector
MW: 30 µV
LW: 40 µV
Speaker outputs
4 – 8 ohms
Audio outputs (3)
Power antenna relay
control lead (CDX-M750)
Power aerial relay
control lead (CDX-M700R)
Power amplifier control
lead
Telephone ATT control
lead
Illumination control lead
12 V DC car battery
(negative ground)
– Continued on next page –
CDX-M750
CDX-M700R
CDX-M750
CDX-M700R
1

Advertisement

Table of Contents
loading

Related Manuals for Sony CDX-M700R

Summary of Contents for Sony CDX-M700R

  • Page 1 Illumination control lead Power requirements 12 V DC car battery Tuning range 87.5 – 107.9 MHz (CDX-M750) (negative ground) 87.5 – 108.0 MHz (CDX-M700R) – Continued on next page – Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity...
  • Page 2 COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

  • Page 3: Table Of Contents

    2-7. Heat Sink ................25 2-8. Chassis (T) Sub Assy ............25 MODEL IDENTIFICATION 2-9. Lever Section ..............26 CDX-M700R have 3 type models. 2-10. Servo Board ............... 26 2-11. Shaft Roller Assy .............. 27 – MODEL NUMBER LABEL –...

  • Page 4: General

    SECTION 1 GENERAL This section is extracted from instruction manual. CDX-M700R CDX-M750...

  • Page 5: Getting Started

    Ver 1.2 2001. 03 (CDX-M700R)

  • Page 7: Radio

    CDX-M700R...
  • Page 8 CDX-M750...

  • Page 9: Rds

    CDX-M700R...

  • Page 10: Dab

    CDX-M700R...

  • Page 14: Tv/Video

    CDX-M750...

  • Page 15: Connections

    CDX-M700R...
  • Page 19 CDX-M750...

  • Page 22: Front Panel Assy (Normal)

    SECTION 2 DISASSEMBLY Note : Follow the disassembly procedure in the numerical order given. 2-1. FRONT PANEL ASSY (NORMAL) 1 Turn on the power and open the front panel. 3 screw (panel) stand 2 screw (panel) 4 front panel assy (Take care not to flexible board pull the flexible...

  • Page 23: Cd Mechanism Block, Flexible Board

    2-3. CD MECHANISM BLOCK, FLEXIBLE BOARD 7 bracket (CD) 5 CD mechanism block 6 PTT 2.6x6 8 cover (flexible) 0 flexible board 3 PTT 2.6x4 9 CNP802 Note: When installing the flexible board, make the board slack as illustrated. 2 PTT 2.6x4 1 PTT 2.6x6 4 CNP701 2-4.

  • Page 24: Motor Block Assy, Cam (R) Assy

    2-5. MOTOR BLOCK ASSY, CAM (R) ASSY Note : Install the motor block assy and cam (R) assy in this roder. For phase alignment between cams (L) and (R), see page 29 and 31. 1 PTT 2.6x6 Note: Install the cam (R) assy with 4 PTT 2.6x6 the cam fully rotated in the direction of the arrow A.

  • Page 25: Heat Sink

    2-7. HEAT SINK 5 heat sink 4 PTT 2.6x8 3 PTT 2.6x8 2 PTT 2.6x12 1 PTT 2.6x8 2-8. CHASSIS (T) SUB ASSY 2 P 2x3 3 P 2x3 1 Unsolder the 4 chassis (T) sub assy lead wires. black white...

  • Page 26: Lever Section

    2-9. LEVER SECTION 5 guide (disc) 6 lever (R) 3 tension spring (LR) 7 lever (L) 1 special screw 2 DISC IN SW board 4 claws 2-10. SERVO BOARD 7 PS 2x4 6 PS 2x4 2 CN2 3 Removal the solders. 1 CN3 4 P 2x3 8 SERVO board...

  • Page 27: Shaft Roller Assy

    2-11. SHAFT ROLLER ASSY • When installing, take note of the positions arm (roller) and washers. (Fig. 1) 3 retaing ring (RA) shaft retainer washer washer 4 shaft retainer shaft retainer retaing ring (RA) Fig. 1 5 shaft roller assy 2 arm (roller) 1 tension spring (RA) 2-12.

  • Page 28: Optical Pick-Up Block

    2-13. OPTICAL PICK-UP BLOCK 1 P 2x3 2 sled motor assy 3 optical pick-up block...

  • Page 29: Phase Alignment

    SECTION 3 PHASE ALIGNMENT 3-1. ARM (A-L) ASSY, ARM (B-L) ASSY 4 arm (A-L) assy 5 stop ring 1.5, type-E 2 stop ring 1.5, type-E 1 arm (B-L) assy 3 spring (arm L) bracket (L) assy 3-2. CAM (L) 1 Move the arm (B-L) assy in the direction of the arrow A and the arm (A-L) assy in the direction of 3 stop ring 1.5, type-E the arrow B fully (full open state).

  • Page 30: Motor Block

    3-3. MOTOR BLOCK 1 Turn the cam (L) and position the cam so that part A does not touch the SWITCH board SW900. 3 PTT 2.6x6 4 PTT 2.6x6 2 motor block SWITCH board 5 B 2.6x4 SW900 cam (L) 3-4.

  • Page 31: Arm (A-R) Assy, Arm (B-R) Assy

    3-5. ARM (A-R) ASSY, ARM (B-R) ASSY 5 stop ring 1.5, type-E 4 arm (A-R) assy 2 stop ring 1.5, type-E 3 spring (arm R) 1 arm (B-R) assy bracket (R) assy 3-6. CAM (R) 1 Move the arm (B-R) assy in the direction of the arrow A and the arm (A-R) assy in the direction of the arrow B fully (full open state).

  • Page 32: Diagrams

    SECTION 4 DIAGRAMS 4-1. IC PIN DESCRIPTIONS • IC501 CXD2598Q (DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD) Pin No. Pin Name Pin Description DVDD — Digital power supply pin DVSS — Digital ground SOUT Servo brock serial data output (Not used.) SOCK Servo brock serial data read clock output (Not used.) XOLT...
  • Page 33 Pin No. Pin Name Pin Description Tracking error signal input Center servo analog input RFDC RF signal input ADIO Test pin (Not used.) AVSSO — Analog ground IGEN Constant current input from OP amplifier. AVDDO — Analog ground ASYO EFM full-swing output (“L”: VSS, “H”: VDD) ASYI Asymmetry comparate voltage input RFAC...
  • Page 34 • IC5 CXP84640-072Q (CD SYSTEM CONTROL) (SERVO BOARD) Pin No. Pin Name Pin Description ITRPT — Not used in this set. 2, 3 — — Not used in this set. 4, 5 — Not used in this set. OPEN Front panel open detection input CLOSE Front panel close control output LINKOFF...
  • Page 35 Pin No. Pin Name Pin Description SENS SENS signal input — — Not used in this set. — — Not used in this set. BU.IN Back-up power detection input BUSON Bus on control input IN SW Disc in switch input (SW3) SELF SW Self switch input (SW2) SCOR...
  • Page 36 • IC301 HD6432355A22F (DISPLAY CONTROL) Pin No. Pin Name Pin Description 1, 2 PG3, 4 Not used. (Open) — Ground — Not used. (Open) — Power supply pin (+5 V) 6 – 9 PC0 – 3 Not used. (Open) — Ground 11 –...
  • Page 37 Not used. (Open) — Power supply pin (+5 V) 90 – 96 PF6 – 0 Not used. (Open) UNI-SO SONY BUS serial data output UNI-SI SONY BUS serial data input 99, 100 — Ground UNI-SCK SONY BUS serial clock input Not used.
  • Page 38 • IC302 CXD2726Q-4 (DIGITAL SIGNAL PROCESSOR, DIGITAL FILTER, D/A CONVERTER) Pin No. Pin Name Pin Description DGND — Ground terminal (digital system) 2 – 21 Input terminal for the test (fixed at “L”) 22 – 24 JPE1 – JPE3 External condition jump terminal “H”: condition jump (fixed at “L”) DVDD —...
  • Page 39 Pin No. Pin Name Pin Description RVDT Serial data input from the master controller (IC801) Serial data 24/32 bit slot selection signal input terminal 24/23BIT “L”: 24 bit slot, “H”: 32 bit slot (validity at slave mode) (fixed at “L” in this set) DVDD —...
  • Page 40 SP LATCH Spectrum analyzer display data latch signal output to display micon. System attenuate control output SYSRST Resetting for slave micon of SONY BUS system. (N/R) Forward/Reverse select output (“L”: forward, “H”: reverse) (Not used in this set.) — Power supply pin (+5 V) (NCO) Not used.
  • Page 41 Pin Description — Power supply pin (+5 V) 4V SEL 4 V select input (Fixed at “L” (CDX-M750) or “H” (CDX-M700R) in this set.) ST-BY Power amplifier drive output (P-SEL) Power select initial setting (Fixed at “L” in this set.)

  • Page 42: Block Diagram -Cd Section

    CDX-M700R/M750 4-2. BLOCK DIAGRAM — CD SECTION — TO TUNER RF AMP, LD APC, DIGITAL SERVO, SECTION TO DISPLAY CD SYSTEM CONTROL SYSTEM CONTROL OPTICAL PICK-UP ERROR AMP DIGITAL SIGNAL PROCESSOR (Page 43) IC801 (1/3) KSS-720A IC501 SECTION (Page 44) •...

  • Page 43: Block Diagram -Tuner Section

    CDX-M700R/M750 4-3. BLOCK DIAGRAM — TUNER SECTION — PJ401 –1 BUS AUDIO IN –2 (M750) R-CH ELECTRONIC VOLUME IC401 IC402 –5 OUT FL LINE OUT Q202 FRONT –6 R-CH 34 ACIFLR 33 AC INLR TUNER UNIT TO DISPLAY 35 SWINR –3...

  • Page 44: Block Diagram -Display Section

    CDX-M700R/M750 4-4. BLOCK DIAGRAM — DISPLAY SECTION — DISPLAY CONTROL IC301 BUS SI UNI SI SB-SI DSP CLK UNI SO UNI SO SYSTEM CONTROL UNI SCK IC801 (3/3) BUS CLK IC302 BUS ON BUS ON AD ON IC405 BU CHECK...

  • Page 45: Circuit Boards Location

    • Waveforms (MODE:PLAY) 4-5. CIRCUIT BOARDS LOCATION THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) for schematic diagram: • All capacitors are in µF unless otherwise noted. pF: µµF Approx.

  • Page 46: Printed Wiring Boards -Cd Mechanism Section

    CDX-M700R/M750 4-6. PRINTED WIRING BOARDS — CD MECHANISM SECTION —...
  • Page 47 CDX-M700R/M750 • Semiconductor Location Ref. No. Location IC501 Q101 (Page 51)

  • Page 48: Schematic Diagram -Cd Mechanism Section (1/2)

    CDX-M700R/M750 • Refer to page 45 for Waveforms. 4-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 60 for IC Block Diagrams. Note: • Voltage and waveforms are dc with respect to ground under no-signal conditions.

  • Page 49: Schematic Diagram -Cd Mechanism Section (2/2)

    CDX-M700R/M750 • Refer to page 45 for Waveforms. 4-8. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 60 for IC Block Diagrams. (Page 48) Note: • Voltage and waveforms are dc with respect to ground under no-signal conditions.

  • Page 50: Printed Wiring Boards -Main Section

    CDX-M700R/M750 4-9. PRINTED WIRING BOARDS — MAIN SECTION — • Semiconductor Location Ref. No. Location Ref. No. Location D301 IC304 (D302) J-11 IC305 J-10 D303 IC306 D304 IC307 D401 (IC308) (D402) IC352 (D403) (IC353) I-11 (D405) IC401 E-11 (D406) IC402...
  • Page 51 CDX-M700R/M750 (Page 47) (Page 56)

  • Page 52: Schematic Diagram -Main Section (1/4)

    CDX-M700R/M750 4-10. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) — • Refer to page 60 for IC Block Diagrams. Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM < > : CD PLAY...

  • Page 53: Schematic Diagram -Main Section (2/4)

    CDX-M700R/M750 4-11. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) — • Refer to page 60 for IC Block Diagrams. Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM ) : AM/MW (Page 54)

  • Page 54: Schematic Diagram -Main Section (3/4)

    CDX-M700R/M750 4-12. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) — • Refer to page 60 for IC Block Diagrams. (Page 52) (Page 53) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM...

  • Page 55: Schematic Diagram -Main Section (4/4)

    CDX-M700R/M750 4-13. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) — • Refer to page 60 for IC Block Diagrams. (Page 52) (Page 53) (Page 57) (Page 59) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM...

  • Page 56: Printed Wiring Board -Sub Section

    CDX-M700R/M750 4-14. PRINTED WIRING BOARD — SUB SECTION — (Page 51)

  • Page 57: Schematic Diagram -Sub Section

    CDX-M700R/M750 4-15. SCHEMATIC DIAGRAM — SUB SECTION — (Page 55) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM...

  • Page 58: Printed Wiring Board -Display Section

    CDX-M700R/M750 4-16. PRINTED WIRING BOARD — DISPLAY SECTION — (Page 50) • Semiconductor Location Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location (D902) B-12 IC902 LED912 B-13 Q901 (D903) C-11 IC903 LED913 Q902 (D904) C-11 LED914...

  • Page 59: Schematic Diagram -Display Section

    CDX-M700R/M750 4-17. SCHEMATIC DIAGRAM — DISPLAY SECTION —...
  • Page 60 • IC Block Diagrams IC1 CXA2596M IC7 LA6556L IC402, 403 NJM2160AM-TE2 IC802 BA8270F-E2 VCCL BUS ON APC PD AMP BUS ON SWITCH HOLD S-GND – BUFFER VCCL INPUT RESET SWITCH CH2-CH4 OUTPUT – SVRL CL– 35 MUTE2 BUS ON MUTE2 ON/OFF LIFT 23 LC/PD...
  • Page 61 IC401 TDA7402TR 33 32 31 24 23 MIXER MONO- MONO- MONO- MONO- MONO- MONO- FADER FADER FADER FADER FADER FADER ACINLF FRONT SUBWOOFER SWINR ACIN +PHASE OUTPUT SWINL REAR CONTROL SELECTOR ACOUTR MAIN ACOUTL SECOND CREF VOICE BANDPASS BASS SUPPLY TREBLE HIGH-CUT VOLUME...

  • Page 62: Exploded Views

    SECTION 5 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • Accessories and packing materials and The components identified by number in the exploded views are not supplied. hardware (# mark) list are given in mark 0 or dotted line with mark •...

  • Page 63: Front Panel Section

    5-2. FRONT PANEL SECTION LCD901 LCD902 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-045-726-01 BUTTON (SOURCE) 1-694-687-11 CONDUCTIVE BOARD, CONNECTION 3-045-725-01 BUTTON (+/–) 1-694-686-11 CONDUCTIVE BOARD, CONNECTION 3-045-727-01 PLATE (RING), LIGHT GUIDE * 67 3-045-708-01 SHEET (SUB), DIFFUSION 3-045-730-01 BUTTON (SEEK) (DSO) * 68...

  • Page 64: Cd Mechanism Section (1)

    5-3. CD MECHANISM SECTION (1) (MG-383V-121//K) M903 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 101 1-676-709-11 DISC IN SW BOARD 3-040-040-01 ARM (ROLLER) 3-040-039-01 CHASSIS (T) * 111 A-3294-808-A SERVO BOARD, COMPLETE 3-040-038-01 SPRING (LR), TENSION * 112 3-040-048-01 BRACKET (MOTOR) 3-040-050-01 LEVER (L)

  • Page 65: Cd Mechanism Section (2)

    5-4. CD MECHANISM SECTION (2) (MG-383V-121//K) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-040-025-01 ARM, CHUCKING A-3307-422-A CHASSIS (M) COMPLETE ASSY 3-040-031-01 DAMPER (T) 3-040-059-01 SPRING (TR), TENSION 3-040-056-01 LEVER (D) 3-040-057-01 LEVER (LOCK) 3-040-024-01 RETAINER (DISC) 3-040-058-01 GEAR (MDL) 3-040-053-01 RING, LOADING 3-040-052-01 WHEEL (U), WORM...

  • Page 66: Cd Mechanism Section (3)

    5-5. CD MECHANISM SECTION (3) (MG-383V-121//K) M901 M902 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 201...

  • Page 67: Electrical Parts List

    3-045-702-01 BRACKET (LCD) (MAIN) 3-045-703-01 PLATE (LCD) (MAIN),LIGHT GUIDE < DIODE > 3-045-704-01 SHEET (MAIN), DIFFUSION LED901 8-719-079-49 LED NSSW450-BRS-TVR (SONY) 3-045-705-01 SHEET (MAIN), REFLECTION LED903 8-719-076-58 LED NSSW440-BRS (LCD BACK LIGHT) 3-045-706-01 BRACKET (LCD) (SUB) LED904 8-719-076-58 LED NSSW440-BRS (LCD BACK LIGHT)
  • Page 68 DISPLAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark LSW909 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (ENTER) R927 1-216-833-11 RES-CHIP 1/16W LSW910 1-771-883-11 SWITCH, TACTILE (WITH LED) (DISC–) R928 1-216-827-11 METAL CHIP 3.3K 1/16W LSW911 1-771-883-11 SWITCH, TACTILE (WITH LED) (CLOSE) R929 1-216-833-11 RES-CHIP 1/16W...
  • Page 69 DISPLAY LIMIT SW MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < SWITCH > C312 1-163-038-00 CERAMIC CHIP 0.1uF C314 1-163-038-00 CERAMIC CHIP 0.1uF S901 1-771-027-21 SWITCH, KEY BOARD (WITH LED) (RESET) C315 1-163-038-00 CERAMIC CHIP 0.1uF S902 1-771-884-11 SWITCH, TACTILE (WITH LED) (MODE)
  • Page 70 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C420 1-124-584-00 ELECT 100uF C491 1-164-346-11 CERAMIC CHIP (M750) C492 1-164-346-11 CERAMIC CHIP C421 1-124-584-00 ELECT 100uF C493 1-164-346-11 CERAMIC CHIP (M750) C494 1-164-346-11 CERAMIC CHIP C422 1-124-261-00 ELECT 10uF C495...
  • Page 71 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C642 1-164-227-11 CERAMIC CHIP 0.022uF C928 1-163-038-00 CERAMIC CHIP 0.1uF C643 1-115-156-11 CERAMIC CHIP C960 1-163-009-11 CERAMIC CHIP 0.001uF C645 1-163-243-11 CERAMIC CHIP 47PF C961 1-163-009-11 CERAMIC CHIP 0.001uF C701 1-164-156-11 CERAMIC CHIP...
  • Page 72 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D805 8-719-977-12 DIODE MA8068-M-TX FB307 1-414-598-11 INDUCTOR, FERRITE BEAD D806 8-719-977-12 DIODE MA8068-M-TX FB308 1-414-598-11 INDUCTOR, FERRITE BEAD D807 8-719-977-12 DIODE MA8068-M-TX FB351 1-414-235-22 FERRITE BEAD INDUCTOR D808 8-719-977-12 DIODE MA8068-M-TX FB801...
  • Page 73 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark JR801 1-216-295-00 SHORT Q461 8-729-049-13 TRANSISTOR UPA1853GR-9JG-E1 JR802 1-216-296-00 SHORT Q601 8-729-920-21 TRANSISTOR DTC314TK-T-146 (M700R) JR806 1-216-295-00 SHORT Q602 8-729-920-21 TRANSISTOR DTC314TK-T-146 (M700R) JR810 1-216-295-00 SHORT Q603 8-729-920-85 TRANSISTOR 2SD1664-T100-QR JR816 1-216-295-00 SHORT...
  • Page 74 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R201 1-216-837-11 METAL CHIP 1/16W R372 1-216-845-11 METAL CHIP 100K 1/16W R202 1-216-081-00 METAL CHIP 1/10W R373 1-216-845-11 METAL CHIP 100K 1/16W R203 1-216-033-00 METAL CHIP 1/10W R374 1-216-845-11 METAL CHIP 100K...
  • Page 75 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R439 1-216-864-11 METAL CHIP 1/16W R612 1-216-295-00 SHORT (M700R) R613 1-216-841-11 METAL CHIP 1/16W R440 1-216-833-11 RES-CHIP 1/16W R614 1-216-041-00 METAL CHIP 1/10W R441 1-216-049-11 RES-CHIP 1/10W R615 1-216-073-00 METAL CHIP 1/10W...
  • Page 76 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R823 1-216-081-00 METAL CHIP 1/10W R908 1-216-825-11 METAL CHIP 2.2K 1/16W R824 1-216-025-11 RES-CHIP 1/10W R909 1-216-811-11 METAL CHIP 1/16W R825 1-216-809-11 METAL CHIP 1/16W R910 1-216-825-11 METAL CHIP 2.2K 1/16W R826...
  • Page 77 MAIN SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark TH803 1-809-148-11 THERMISTOR PTH8L07AR2R0M1B510 C517 1-164-360-11 CERAMIC CHIP 0.1uF C518 1-164-360-11 CERAMIC CHIP 0.1uF < TUNER > C519 1-164-360-11 CERAMIC CHIP 0.1uF C520 1-164-360-11 CERAMIC CHIP 0.1uF TU601 A-3220-738-A TUNER UNIT (TUX-020)
  • Page 78 SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R127 1-216-821-11 METAL CHIP 1/16W R563 1-216-809-11 METAL CHIP 1/16W R213 1-216-821-11 METAL CHIP 1/16W R564 1-216-845-11 METAL CHIP 100K 1/16W R214 1-216-821-11 METAL CHIP 1/16W R568 1-216-837-11 METAL CHIP 1/16W R301...
  • Page 79 SWITCH Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < SWITCH > ************** HARDWARE LIST SW501 1-692-135-21 SWITCH, KEY BOARD (RESET) ************** SW504 1-692-135-21 SWITCH, KEY BOARD (Z) 7-685-790-09 SCREW +PTT 2.6X4 (S) ************************************************************* 7-685-792-09 SCREW +PTT 2.6X6 (S) A-3326-298-A SWITCH BOARD, COMPLETE 7-621-775-10 SCREW +B 2.6X4 (INCLUDING SW900)
  • Page 80 Ref. No. Part No. Description Remark PARTS FOR INSTALLATION AND CONNECTIONS *************************************** 3-014-370-21 FRAME, FITTING 3-916-012-01 BRACKET (ND), FITTING ASSIST (M750) 7-682-160-01 SCREW +P 4X6 (M750) X-3368-725-1 SCREW ASSY, FITTING (M750) X-3378-770-1 COLLAR ASSY 3-386-828-01 SCREW, FITTING (M700R) 3-349-410-01 BUSHING (M700R) X-3366-405-1 SCREW ASSY (EXP), FITTING (M700R) 3-030-929-02 SPRING, FITTING 3-934-325-01 SCREW (+K 5X8 TP)
  • Page 81 CDX-M700R/M750 MEMO...
  • Page 82 CDX-M700R/M750 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2001.

This manual is also suitable for:

Cdx-m750

Table of Contents