Spanish Quick Use Guide is included. Guía para rápida consulta en español está incluida. For USA assistance, please call: 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.com/contactinfo For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.ca P PC...
Things You Should Know Thank you for choosing Panasonic! You have purchased one of the most sophisticated and reliable products on the market today. Used properly, we’re sure it will bring you and your family years of enjoyment. Please take time to fill in the information on the right.
Page 3
Model No.: VDR-D230/VDR-D310 Responsible party: Panasonic Corporation of North America One Panasonic Way, Secaucus, NJ 07094 Support Contact: Panasonic Consumer Electronics Company 1-800-211-PANA (7262) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings.
Page 5
Precautions USE & LOCATION WARNING ≥ TO AVOID SHOCK HAZARD ... Your camera and power supply should not be exposed to rain or moisture. Do not connect the power supply or operate your camera if it gets wet. Your camera has been designed for outdoor use, however it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or a direct splashing from a pool or...
Page 6
Batteries Battery pack (Lithium ion battery pack) ≥ Use the specified unit to recharge the battery pack. ≥ Do not use the battery pack with equipment other than the specified unit. ≥ Do not get dirt, sand, liquids, or other foreign matter on the terminals. ≥...
Page 7
-If you see this symbol- Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal. ≥...
Page 8
Contents Before using Features ... 10 Quick Guide ... 12 Accessories ... 15 Parts identification and handling ... 16 Using the LCD monitor ...19 Using the viewfinder ...20 Using the remote control (VDR-D310) ...20 Discs and cards... 22 Discs that can be used on this unit...22 Cards that you can use with this unit (VDR-D310/VDR-D230) ...26 Disc and card handling...27...
Page 9
Displaying disc information...83 Card management (VDR-D310/VDR-D230) ... 83 Formatting an SD card ...83 With other products With a TV... 85 Playback on TV ...85 With a DVD recorder/player...86 Playback on DVD recorder, DVD player, computer etc...86 Copying (dubbing) recordings onto a DVD recorder’s hard disk ...87 With a VCR...
Before using Before using Features ∫ Easy recording! (l 46) No need to search for the recording start position. The new recording will not overwrite any previously recorded scene. ∫ Easy playback! (l 65) Recorded scenes are displayed as thumbnails. You can easily search for the scenes you want to watch.
Page 11
If you insert a DVD-RW or a DVD-R disc recorded in this unit (that has not been finalized) into another device such as DVD recorder, computer, etc., the disc may become unusable. Be sure to finalize the disc on this unit before inserting it in other devices. (l 81) ∫...
Before using Quick Guide ∫ Charging the battery Connect the AC cable to the AC adaptor and the AC outlet. Put the battery on the battery mount by aligning the mark, and then securely plug it in. ∫ Inserting the battery Push the battery against the battery holder and slide it until it clicks.
∫ Inserting/removing an SD card (VDR-D310/VDR-D230) Slide the card slot cover to open. Insert/remove the SD card into/from the card slot. Securely close the card slot cover. ∫ Recording motion pictures ≥ Rotate the mode dial to select Press the recording start/stop button to start recording.
Page 14
Before using Press the Photoshot button [ take the picture. VDR-D230: Press the Photoshot button [ ∫ Motion picture playback ≥ Rotate the mode dial to select Select the scene to be played back. Press the joystick. LSQT1145 ] fully to Move the joystick to operate.
Stops the playback and shows the ∫: thumbnails. Accessories Check the accessories before using this unit. Battery pack (VDR-D310) CGA-DU12 Battery pack (VDR-D230/VDR-D210) CGR-DU06 AC adaptor PV-DAC14D AC cable K2CA2CA00029 or K2CA2CA00025 DC cable K2GJ2DC00011 AV/S cable (VDR-D310/VDR-D230) K2KZ9CB00001 AV cable (VDR-D210) K2KC4CB00020 Remote control...
Before using VDR-D310: <For USA-California only> This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special handling may apply. www.dtsc.ca.gov/hazardouswaste/perchlorate. Parts identification and handling Lens (LEICA DICOMAR) (VDR-D310) Lens (VDR-D230/VDR-D210) Video light (VDR-D230) (l 54) Microphone (built-in, stereo) White balance sensor (l 62) Remote control sensor (VDR-D310) (l 21)
Page 17
23 Tripod receptacle (l 19) 24 Battery release lever [BATTERY] (l 28) VDR-D310 VDR-D230 VDR-D210 25 LCD monitor (l 19) Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the LCD monitor screen. However, this is not a malfunction and does not affect the recorded picture.
Before using Using grip belt Adjust the belt length so it fits your hand. U.S.A. only When this unit is purchased, a sensor tag is attached to the grip belt. Remove the tag before use. 1 Flip the belt. 2 Take off the tag. 3 Replace the belt.
Lens hood Rotate the lens hood counter- clockwise A to remove it. ∫ VDR-D310 In order to attach it, place into slot B, and then rotate it clockwise C. ∫ VDR-D230/VDR-D210 In order to attach it, rotate it clockwise B. Tripod receptacle This is a hole for attaching the unit to the optional tripod.
Before using Place your finger on the LCD monitor open part A and pull the LCD monitor out in the direction of the arrow. ≥ It can open up to 90o. Adjust the angle of the LCD monitor as desired. ≥...
Dispose of used batteries according to the manufacturer’s instructions. Replace battery with Panasonic PART NO. CR2025 only. Use of another battery may present a risk of fire or explosion. Caution: Battery may explode if mistreated.
Before using Discs and cards Discs that can be used on this unit Disc type Recording format Characteristic Display on the screen Indication in these instructions Functions ≥ Deleting recorded scenes ≥ Editing on this unit ≥ Playback on other products ≥...
Page 23
Disc type Recording format Characteristic Display on the screen Indication in these instructions Functions ≥ Deleting recorded scenes ≥ Editing on this unit ≥ Playback on other products ≥ Recording after finalizing *1 By formatting the disc, it can be used repeatedly. (l 82) *2 DVD players and DVD recorders that support 8 cm (3z) discs.
Page 24
≥ Discs inserted in a holder, cartridge, or caddy case cannot be used. Always remove bare discs from these containers prior to use. ≥ It is recommended that you use Panasonic discs. Usually discs compatible with the DVD standard can be used for recording and playback with no problems. However, some commercially available discs do not meet the DVD standard for quality and performance.
Page 25
When using brand-new DVD-RW When using DVD-RW, select whether to record in DVD Video Recording format (VR format) or DVD- Video format (Video format) and then format the disc. (l 24, About format types) When a brand-new DVD-RW is inserted in this unit, the screen on the right appears.
SD card. (l 83) ≥ We recommend that you use a Panasonic brand SD card. ≥ When the write-protect switch A on SD card is locked, no recording, deletion or editing will be possible on the card.
Disc and card handling ∫ How to hold a disc or card Do not touch the recording/playback surface or the terminal surface. ∫ When inserting/removing a disc Do not allow the recording/playback side of the disc to get dirty and avoid fingerprints. ≥...
CHARGE lamp flashes and the charging time will be longer than normal. ≥ Battery charging time (l 29) ≥ We recommend using Panasonic batteries. (l 15, 143) ≥ If you use other batteries, we cannot guarantee the quality of this product.
Charging time and recordable time The times shown in the tables below are for when the temperature is 25 oC (77 oF) and the humidity is 60%. If the temperature is higher or lower than 25 oC (77 oF), the charging time will become longer. ∫...
Page 30
Setup ∫ Recordable time (When using a DVD-RAM disc) ≥ The times indicate the recordable time when the viewfinder is used. The times in parentheses indicate the recordable time when the LCD monitor is used. ≥ The actual recordable time refers to the recordable time on a disc when repeatedly starting/stopping recording, turning the unit on/off, moving the zoom lever, etc.
Page 31
VDR-D230/VDR-D210: Battery model number Supplied battery/ CGR-DU06 (optional) CGA-DU12 (optional) CGA-DU21 (optional) ≥ The display changes as the battery capacity reduces. If the battery discharges, then ≥ The recordable times will vary depending on the status of use. These times are approximations. The recordable time will become shorter when you use both the viewfinder and the LCD monitor simultaneously while rotating the LCD monitor frontward to record yourself, etc.
Setup Connecting to the AC outlet Connect the AC cable to the AC adaptor and the AC outlet. Connect the DC cable to the AC adaptor. Connect the DC cable to this unit. ≥ Do not use the AC cable with any other equipment as it is designed only for this unit.
When the power is turned on for the first time after changing the disc or battery, the unit carries out a recognition procedure to check that there are no problems with the disc. This takes approximately 25 seconds with DVD-RAM. If you want to start using the unit as soon as you turn on the power, do the following.
Page 34
Setup A few moments after the ACCESS/PC lamp blinks, the cover of the disc compartment will open slightly. Open the cover of the disc compartment by hand and insert/ remove the disc. ∫ Inserting disc Fit the disc onto the spindle in the center and then push the disc down until it clicks into place.
“SIDE B” recording/playback side is the side with the “SIDE A” mark. A “SIDE A” mark B The opposite side is the “SIDE A” recording/ playback side. ≥ Do not use excessive force when opening the cover. ≥ Do not touch the pickup lens or the recording/ playback side of the disc.
Setup Insert/remove the SD card into/ from the card slot. ≥ When inserting an SD card, face the label side A upwards and press it straight in as far as it goes. ≥ When removing the SD card, press the center of the SD card and then pull it straight out.
Move the joystick up, down, left, or right to select an item or scene, and then press the joystick to set it. 1 Select by moving up. 2 Select by moving down. 3 Select by moving left. 4 Select by moving right. 5 Press the joystick to select the item.
Page 38
Setup About the operation icons displayed in each mode About auto mode and manual mode (l 45) Video recording mode 1/2 NEXT 1/2 1/2 NEXT NEXT 2/2 2/2 NEXT 2/2 NEXT NEXT Icon (1/2) (2/2) In manual mode (3/3) In manual focus mode (4/4) ≥...
Page 39
Picture recording mode (VDR-D310/VDR-D230) 1/2 NEXT 1/2 1/2 NEXT NEXT 2/2 2/2 NEXT 2/2 NEXT NEXT Icon Ø (1/2) (2/2) In manual mode (3/3) In manual focus mode (4/4) Picture playback mode (VDR-D310/VDR-D230) Icon Direction ∫ 3/3 NEXT 3/3 3/3 NEXT NEXT Direction Backlight compensation...
Setup ∫ Help mode The help mode explains the operation icons that are displayed when the AUTO/MANUAL/FOCUS switch is set to AUTO in video/picture recording mode. ¬ Rotate the mode dial to select Press the joystick to display the icon during the recording pause. Move the joystick right to select Move the joystick up, left or right to select the desired icon.
Page 41
Move the joystick up or down in order to select the desired top menu. Move the joystick right or press the joystick. Move the joystick up or down in order to select the submenu item. Move the joystick right or press the joystick.
Setup ≥ Use the direction buttons (3,4,2,1) and ENTER button in place of the joystick on the main unit. Press the MENU button to exit the menu screen. MENU ENTER Setting date and time When the unit is turned on for the first time, a message asking you to set the date and time will appear.
≥ The date and time function are driven by a built-in lithium battery. ≥ Make sure to check the time before recording. ≥ If the time display becomes [- -], the built-in lithium battery has run down. Use the following steps to charge the battery.
Recording Recording Before recording Basic camera positioning 1 Hold the camera with both hands. 2 Put your hand through the grip belt. 3 Do not cover the microphones or sensors with your hands. 4 Keep your arms near your body. 5 Slightly open your legs.
Page 45
∫ About auto mode Set the AUTO/MANUAL/FOCUS switch to AUTO, and color balance (white balance) and focusing will be adjusted automatically. jAuto white balance (l 136) jAuto focusing (l 137) Depending on the brightness of the subject etc., the aperture and shutter speed are automatically adjusted for an optimum brightness.
Recording Recording motion pictures Record motion pictures onto a disc. ≥ When the unit is purchased, the aspect ratio is set to [16:9] for recording images compatible with a wide-screen TV. To watch images on a regular TV (4:3), change the aspect ratio setting (l 59) before recording the images or when watching them on the connected TV (l 85).
≥ When about 5 minutes have passed without any operation in recording pause, the unit automatically turns off to prevent the battery from running down. When you want to use the unit, turn it on again. This setting can also be set to [OFF]. (l 117, [POWER SAVE]) Screen indications in the video recording mode A Recording mode B Remaining time left for recording...
Recording ∫ Approximate recordable time for 1 disc (single sided) Disc type DVD-RAM DVD-R DL ≥ This unit records in VBR. VBR is an abbreviation for Variable Bit Rate. VBR recording automatically varies the bit rate (amount of data in a fixed time) depending on the subject being recorded. This means if a subject with sharp movements is recorded, the recording time is reduced.
Recording still pictures (JPEG still pictures) (VDR-D310/VDR-D230) Record the still picture on an SD card. ≥ When this unit is purchased, [PICTURE SIZE] is set to [ recording pictures compatible with a wide-screen TV (16:9). To record pictures with a 4:3 aspect ratio, change the [PICTURE SIZE] setting before recording (l 52).
Recording A Shutter chance mark ± (The white lamp flashes.): ¥ (The green lamp lights up.): When in focus No mark: ≥ The shutter chance mark is indicated as follows when the Photoshot button [ ] is not pressed halfway. Please use it as a guide for recording.
Page 51
∫ To record still pictures clearly ≥ When zooming in on the subject with a magnification of 4k or higher, it is difficult to reduce the slight shaking from holding this unit by hand. We recommend decreasing the zoom magnification and approaching the subject when recording.
Recording Number of pixels and picture quality for still picture recording ∫ [PICTURE SIZE] Changing the recording size. Press the MENU button, then select [BASIC] # [PICTURE SIZE] # desired item and press the joystick. VDR-D310: Icon Aspect 16:9 VDR-D230: Icon Aspect 16:9...
Various recording functions Zoom in/out function (RAM) (-RW‹VR›) (-RW‹V›) (-R) (SD) VDR-D310: You can zoom in up to 10k optically. VDR-D230/VDR-D210: You can zoom in up to 32k optically. ¬ Rotate the mode dial to select Move the zoom lever. T side: Close-up recording (zoom in) W side: Wide-angle recording (zoom out) ≥...
Recording ≥ This function cannot be used in picture recording mode. To use the zoom microphone function (RAM) (-RW‹VR›) (-RW‹V›) (-R) The zoom microphone is linked to the zooming operation so that far-away sounds with a tele- shot and close-up sounds with a wide-angle shot are recorded more clearly.
To eliminate washed out images, use this mode. 3 Video light off ≥ The subject should be within 1.5 m (5 feet) of the unit. ≥ Using the video light reduces battery time. ≥ Set the video light to off when not in use. ≥...
Recording Move the joystick left to select Press the recording start/stop button. Start recording. (Fade in) When you start recording, the image/audio gradually appears. Pause recording. (Fade out) The image/audio gradually disappears. After the image/audio completely disappears, recording stops. ≥ After recording, the fade setting is canceled. To cancel fading Select [ ] again.
≥ If the background or anything else in the scene has colors similar to the skin color, they will also be smoothed. ≥ If the brightness is insufficient, the effect may not be clear. ≥ You may not be able to see the face clearly when recording a distant person.
Recording ≥ If it is difficult to focus, adjust the focus manually. (l 61) To cancel the MagicPix function Select [ ] again. ≥ The MagicPix function makes the signal charging time of CCD up to approximately 30k longer than usual, so that dark scenes can be recorded brightly.
To cancel the Recording guideline function Press the MENU button, then select [BASIC] # [GUIDE LINES] # [OFF] and press the joystick. ≥ The guidelines do not appear on the images actually recorded. ≥ The guidelines are not displayed while rotating the LCD monitor frontward to record yourself.
Recording ¬ Rotate the mode dial to select Press the MENU button, then select [ADVANCED] # [WIND CUT] # [ON] and press the joystick. To cancel the wind noise reduction function Press the MENU button, then select [ADVANCED] # [WIND CUT] # [OFF] and press the joystick.
≥ Avoid recording under fluorescent light, mercury light or sodium light because the color and brightness of the playback image may change. ≥ If you record a subject illuminated with strong light or a highly reflective subject, vertical lines of light may appear. ≥...
Page 62
Recording Set the AUTO/MANUAL/FOCUS switch to MANUAL. The icon shown in the illustration is displayed automatically. Move the joystick up to select Move the joystick left or right to select the white balance mode. ] Auto white balance adjustment Indoor mode (for recording under incandescent lamps) ≥...
will temporarily be black. (The black balance cannot be adjusted manually.) 1 Black balance adjustment in progress. (Flashes.) 2 White balance adjustment in progress. (Flashes.) 3 Adjustment completed. (Lights up.) ≥ When the unit is turned on with the lens cap attached, the automatic white balance adjustment may not function properly.
Page 64
Recording ≥ You may see vertical lines of light in the playback image of a brightly shining subject or highly reflective subject, but this is not a malfunction. ≥ During normal playback, image movement may not look smooth. ≥ When recording in an extremely bright place, the screen may change color or flicker.
Playback Motion picture playback Play back the motion pictures and the MPEG still pictures (VDR-D210) recorded on the disc. Rotate the mode dial to select The motion pictures and the MPEG still pictures (VDR-D210) recorded on the disc are displayed as thumbnails.
Page 66
Playback ≥ The time displayed may be different from the recording time and it may take time to display the thumbnail display when playing back motion pictures recorded on another product. ≥ The recording time is not displayed on the screen during playback of scenes recorded on other products.
Move the joystick up during playback to pause the playback. Move the joystick right. (The frames will be advanced one at a time in the reverse direction when you move the joystick left.) ≥ Normal playback is restored when you move the joystick up. ∫...
Playback Select the date for playback, then press the joystick. The scenes recorded on the same day are displayed as thumbnails. Select the scene to be played back. ≥ Even if scenes are recorded on the same day, they are grouped separately in the following cases. jWhen the number of scenes exceeds 99 (RAM) (-RW‹VR›) (-RW‹V›) (-R) jWhen the disc is removed (-RW‹V›) (-R) jWhen the [ASPECT] setting is changed (-RW‹V›) (-R)
Still picture playback (JPEG still pictures) (VDR-D310/VDR-D230) Play back the still pictures recorded on the card. Rotate the mode dial to select The still pictures recorded on the SD card are displayed as thumbnails. Select the file to be played back. A File number B Scroll bar display The selected file will be encircled by a yellow frame.
Page 70
Playback ≥ Do not operate the mode dial during the slide show. ≥ While this unit accesses the SD card (the access lamp is lit), do not remove the SD card. ≥ It takes time to display the file depending on the number of pixels of the file. ≥...
Editing scenes Editing Deleting scenes This is for deleting scenes recorded on discs. The deleted scenes cannot be restored. ≥ Scenes on DVD-RW (Video format) and DVD- R cannot be deleted. Deleting scenes one at a time ¬ Rotate the mode dial to select Press the button during playback.
Editing ≥ Do not turn off this unit while deleting. ≥ When you delete scenes, use a battery with sufficient battery power or use the AC adaptor. ≥ It may not be possible to delete scenes that have been divided. Combine the divided scenes, and then delete them.
Select the scene to be combined, then press the joystick. ≥ The selected scene and the next scene are combined. ≥ If you wish to combine scenes that are not next to each other or scenes with different recording dates, first create a playlist and then combine the scenes on the playlist.
Editing Select the scene to be added to the playlist, then press the joystick. The selected scene is encircled by a red frame. ≥ When the joystick is pressed again, the selected scene will be canceled. ≥ Up to 50 scenes can be set in succession. ≥...
Deleting scenes ≥ Deleting scenes on a playlist will not affect the original scenes. ∫ Deleting scenes one at a time ¬ Select playlist playback mode. (l 74, steps 1 and 2) Press the button during playback. When the confirmation message appears, select [YES], then press the joystick.
Page 76
Editing Press the MENU button, then select [EDIT] # [ADD] # [YES] and press the joystick. Select the scene to be added, then press the joystick. The selected scene is encircled by a red frame. ≥ When the joystick is pressed again, the selected scene will be canceled.
Page 77
Press the MENU button, then select [EDIT] # [DIVIDE] # [YES] and press the joystick. Select the scene to be divided, then press the joystick. The selected scene is played back. When you reach the area where you want to divide the scene, move the joystick down to set the dividing point.
Editing Editing still pictures (VDR-D310/VDR-D230) Deleting still pictures This is for deleting still picture files recorded on SD cards. The deleted files cannot be restored. Deleting files one at a time ¬ Rotate the mode dial to select Press the button during playback.
≥ If files conforming to DCF standard are deleted, all the data related to the files will be deleted. Locking still pictures This is for preventing still picture files from being deleted by mistake. Still picture files recorded on an SD card can be locked so that they are not deleted by mistake.
Page 80
Editing To cancel all DPOF settings Press the MENU button, then select [PICT. SETUP] # [DPOF SET] # [CANCEL ALL] and press the joystick. ≥ When the confirmation message appears, select [YES], then press the joystick. ∫ What is DPOF? DPOF stands for Digital Print Order Format.
Disc management Disc and card management Finalizing a disc It allows the discs to be played on other devices. (-RW‹VR›) (-RW‹V›) (-R) If you insert a DVD-RW or a DVD-R disc recorded in this unit (that has not been finalized) into another device such as DVD recorder, computer, etc., the disc may become unusable.
Disc and card management Un-finalizing a DVD-RW This is for un-finalizing a DVD-RW (Video format) so that it can be used for recording. ¬ Rotate the mode dial to select Press the MENU button, then select [DISC SETUP] # [UN-FINALIZE] # [YES] and press the joystick.
[FORMAT DISC] # [YES] and press the joystick. ≥ When formatting a DVD-RAM, skip to step 3. (When formatting a DVD-RW only) Select format type (l 24), then press the joystick. When the confirmation message appears, select [YES], then press the joystick.
Page 84
Disc and card management Press the MENU button, then select [SETUP] # [FORMAT CARD] # [YES] and press the joystick. When the confirmation message appears, select [YES], then press the joystick. ≥ When formatting is complete, press the MENU button to exit the message screen. ≥...
With a TV With other products Playback on TV (RAM) (-RW‹VR›) (-RW‹V›) (-R) (SD) The motion pictures and still pictures recorded by this unit can be played back on a TV. ≥ Use the AC adaptor to free you from worrying about the battery running down.
With other products ≥ This function’s default setting is [16:9]. ∫ To display the on-screen information on the TV (VDR-D310) The information displayed on the screen (operation icon and time code, etc.) can be displayed on the TV. Press the EXT DISPLAY button on the remote control.
Refer to the operating instructions of the playback device. ≥ The recording time is not displayed. Copying (dubbing) recordings onto a DVD recorder’s hard disk (RAM) (-RW‹VR›) (-RW‹V›) (-R) If you have a DVD recorder with hard disk, images recorded by this unit can be stored on the hard disk.
With other products Connect this unit and a video device. S VIDEO IN VIDEO IN AUDIO IN A AV/S cable (VDR-D310/VDR-D230) (supplied) AV cable (VDR-D210) (supplied) ≥ Insert the plugs as far as they will go. * If the video device has an S Video terminal, also connect the S Video plug into it.
Page 89
Select a file to be printed, then press the joystick. The number of pictures set is displayed. Move the joystick up or down to select the desired number of prints, then press the joystick. ≥ You can set up to 9 prints. ≥...
Page 90
With other products ≥ You may not be able to print still pictures recorded with other products. ≥ When the unit is connected directly to the printer, the DPOF settings cannot be used. ≥ Connect the printer directly to this unit. Do not use a USB hub.
With a computer (VDR-D310/VDR-D230) Before using with a computer (Windows) What you can do with a computer ∫ When using a DVD-RAM or DVD-RW (VR format) recorded on this unit ≥ Before using DVD-RW (VR format) on a computer, be sure to finalize it on this unit. Can do Playing back on a computer Copying a disc...
With a computer (VDR-D310/VDR-D230) Contents on provided CD-ROM The following software applications are contained on the provided CD-ROM. ∫ DVD-RAM Driver This is necessary to configure the unit as a drive on a computer. DVDForm: This is used to format DVD-RAM on a computer. ∫...
Page 93
∫ DVDfunSTUDIO This software is for creating a DVD-Video disc. Use this software when burning a DVD-Video disc from motion pictures edited using DVD-MovieAlbumSE. For details, refer to page 105. Export the images from a DVD-RAM or DVD-RW (VR format) with DVD-MovieAlbumSE.
With a computer (VDR-D310/VDR-D230) Operating environment ≥ A CD-ROM drive is necessary to install the supplied software applications. ≥ When 2 or more USB devices are connected to a computer, or when devices are connected through USB hubs or by using extension cables, proper operation is not guaranteed. ≥...
Page 95
∫ DVDfunSTUDIO 2.5 Personal computer Display Free hard disk space Sound Interface Necessary software ≥ Even if the system requirements mentioned in these operating instructions are fulfilled, some computers cannot be used. ≥ This software cannot be used on a Macintosh OS. ≥...
With a computer (VDR-D310/VDR-D230) ∫ Using Built-in SD Drive Personal computer Interface ≥ The USB equipment operates with the driver installed as standard in the OS. LSQT1145 IBM PC/AT compatible personal computer Microsoft Windows 2000 Professional Microsoft Windows XP Home Edition Microsoft Windows XP Professional Intel Pentium II 300 MHz or higher 32 MB or more (64 MB or more recommended)
End User License Agreement Before opening the CD-ROM package, please read the following. You (“Licensee”) are granted a license for the Software defined in this End User Software Agreement (“Agreement”) on condition that you agree to the terms and conditions of this Agreement.
With a computer (VDR-D310/VDR-D230) ≥ Before starting the installation, close any other software applications which are running. ≥ Do not perform any other operations on your computer while the software is being installed. ≥ If another DVD-RAM Driver is already installed in your computer, check this DVD-RAM Driver.
Check the contents, then click [k] at the top right of window. Click [Finish]. Windows 2000 only: The detection of device will start, after which it will take several minutes for the computer to detect the device. When detecting the device is complete, a message that prompts you to reboot will appear: Click [Yes].
With a computer (VDR-D310/VDR-D230) Select [NTSC (North America)] for the TV system, click [Next]. Continue to follow the on-screen messages to install it. Click [Finish]. The computer must be rebooted for the application to work. Installing DVDfunSTUDIO Insert the CD-ROM into the computer.
With a computer (VDR-D310/VDR-D230) Select the software application to be deleted, then click [Change/ Remove] ([Change or Remove] or [Add/Remove]). ≥ Proceed with the uninstallation by following the on-screen instructions. ≥ After uninstalling the software, be sure to reboot the computer. Connection and recognition (Windows) Connection and recognition...
≥ When a computer is accessing a disc or card in this unit, the ACCESS/PC lamp or card access lamp lights. (When a card is being accessed, appears on the LCD monitor.) Do not disconnect the USB cable or AC adaptor while the disc or card is being accessed as it may damage the data.
With a computer (VDR-D310/VDR-D230) ≥ When data not supported by this unit has been recorded on a computer, it will not be recognized by this unit. To disconnect USB cable safely Double click the tray. Hardware disconnect dialog appears. ≥ Depending on your computer’s settings, this icon may not be displayed.
USB cables.) The USB function selection screen will appear. Select [PC CONNECT(DISC)] and press the joystick. (On the computer) Select [start] # [All Programs (Programs)] # [Panasonic] # [DVD camcorders] # [DVD camcorders], then click [DVD-MovieAlbum]. turn on LSQT1145...
Page 106
With a computer (VDR-D310/VDR-D230) ≥ If the screen showing a brief explanation of the application is displayed, close it. DVD-MovieAlbumSE starts and the images recorded on the disc are displayed. When starting DVD-MovieAlbumSE, the [Mount Information] dialog box may appear or the recorded images may not be shown.
Page 107
Click [Burning]. Writing to the disc starts. When writing is complete, the disc is ejected automatically. ≥ The DISC EJECT lever on this unit does not work when the unit is connected to a computer. Use the software’s eject button to eject the disc.
With a computer (VDR-D310/VDR-D230) Before using with a computer (Macintosh) What you can do with a computer ∫ When using a disc recorded on this unit Before using DVD-RW (VR format), DVD-RW (Video format) and DVD-R on the computer, finalize them on this unit.
Contents on provided CD-ROM The following software application is contained on the provided CD-ROM. ∫ ImageMixer 3 This software is for playing back motion pictures recorded on a disc, importing motion pictures to a computer, creating a DVD-Video disc etc. Use this software when burning a DVD-Video disc from motion pictures recorded on this unit.
≥ The USB equipment operates with the driver installed as standard in the OS. For technical inquiries about these software applications, contact the PIXELA Customer Support Center in your region. U.S. and Canada (Toll-Free) +1-800-458-4029 Website: http://www.pixela.co.jp/oem/panasonic/e/index.html (This website is in English only.) LSQT1145...
≥ Do not perform any other operations on your computer while the software is being installed. Insert the CD-ROM into the computer. [PANASONIC] CD-ROM icon appears. Double-click [PANASONIC] # [ImageMixer3forDVDPalmcorder. pkg]. The installer setup screen appears.
With a computer (VDR-D310/VDR-D230) Using discs on a computer (Macintosh) Creating a DVD-Video on a computer from a recorded disc Using ImageMixer 3, you can create a DVD- Video disc from the images recorded on this unit. ≥ Before using DVD-RW (VR format), DVD-RW (Video format) or DVD-R on a computer, finalize them on this unit.
Select the scenes to be added to the DVD-Video and then click [DVD List]. Select the DVD menu, the disc size and the picture quality and then click [OK]. A new list is created in [DVD List] in [Source]. ≥ You can add images to the disc to be created by dragging and dropping files from the library to the created list.
With a computer (VDR-D310/VDR-D230) ≥ If you disconnect the USB cable while the access lamp is on, it may damage the data. Using an SD card on a computer (Macintosh) Connection ¬ Connect this unit to the AC adaptor. Insert an SD card with recorded images in the unit, then turn on the unit.
To disconnect USB cable safely Drag the [NO_NAME] icon into the Trash and then disconnect the USB cable. ≥ If you disconnect the USB cable while the access lamp is on or while LCD monitor, it may damage the data. With a computer (VDR-D310/VDR-D230) appears on the LSQT1145...
Others When you turn on the power When this unit is recognized by the computer or the printer, etc. 2 Beeps When you pause recording When you turn off the power 2 Beeps for 4 times When an error occurs e.g. recording not starting. Check the sentence displayed on the screen.
Page 120
Others DPOF already set (to more than 1) Locked still pictures Number of recording pixels for VDR-D310: still pictures 2048k1512 1920k1080 1280k960 640k480 VDR-D230: 640k480 640k360 The picture size is not displayed for still pictures recorded with other products that have different picture sizes from the sizes shown above.
You inserted a disc that does not meet the DVD standard for quality and performance so you may not be able to record normally. Refer to the following support site for information about discs that have been confirmed as compatible by Panasonic. http://panasonic.co.jp/pavc/global/cs/e_cam (This website is in English only.) The AGS function is activated.
Others CARD LOCKED. CARD FULL. PUSH THE RESET SWITCH. CHECK THE DISC AFTER PUSHING THE RESET SWITCH TO REPAIR THE DATA. CHANGE TO MANUAL MODE. CANCEL MAGICPIX MODE. TURN OFF THE VIDEO LIGHT. CANNOT SET. PLEASE CONNECT AC ADAPTOR DISCONNECT USB CABLE.
Functions that cannot be used simultaneously Some functions in this unit are disabled or cannot be selected due to the unit’s specifications. The table below shows examples of functions restricted by various conditions. Functions Digital zoom Fade MagicPix Backlight compensation Soft skin mode (Set and cancel) Tele macro (Set and cancel) Help mode...
Others Frequently asked questions What kind of discs can be used? DVD-RAM, DVD-RW, DVD-R and DVD-R DL can be used if they are 8 cm (3z) non-cartridge discs. (l 22) Can discs with a cartridge be used? They can be used if the cartridge is removed. Can double sided discs be used? They can be used.
Page 125
Is playback possible on a computer? (Windows) DVD-RAM, DVD-RW (VR format): Use the supplied software DVD-MovieAlbumSE. ≥ Before using DVD-RW (VR format) on a computer, be sure to finalize it on this unit. DVD-RW (Video format), DVD-R: Finalize the disc on this unit and then play it back with commercially available DVD- Video playback software.
Page 126
Others Is editing possible on a computer (Macintosh)? Use ImageMixer 3. ≥ Motion pictures that have been saved to the ImageMixer 3 library can be edited. ≥ Before using DVD-RW (VR format), DVD-RW (Video format) or DVD-R on a computer, finalize them on this unit.
Troubleshooting Problem This unit cannot be turned on. This unit is turned off automatically. This unit does not stay on long enough. A clicking sound is heard when the power is turned off. Battery runs down quickly. This unit cannot be operated though it is turned on.
Page 128
Others Problem The remote control does not function. The DISC EJECT lever does not work. The disc cannot be read. A function indication such as the remaining time indication or the elapsed time indication is not shown. Recording does not start although power is supplied to this unit and the disc or card is...
Page 129
Problem Recorded still pictures are not clear. Auto focus function does not work. Sound is not played back from the built-in speaker of this unit. Although this unit is correctly connected to a TV, playback images cannot be seen. The playback images are squeezed horizontally.
Page 130
Others Problem The indication disappears. The screen is frozen. No operation can be performed. “PUSH THE RESET SWITCH.” or “CHECK THE DISC AFTER PUSHING THE RESET SWITCH TO REPAIR THE DATA.” is displayed. If the SD card is inserted in another device, it is not recognized.
Page 131
Problem When DVD-MovieAlbumSE is started, the [Mount Information] dialog box appears. An image that should have been recorded does not appear when DVD-MovieAlbumSE is started. DVD-RW (Video format) or DVD-R cannot be played back on DVD-MovieAlbumSE. The DISC EJECT lever does not work when the unit is connected to the computer.
Page 132
Others With a computer (Macintosh) Problem Even if connected by the USB cable, this unit is not recognized by the computer. DVD-RAM or DVD-RW (VR format) icon is not displayed on the desktop. Cannot select this unit as the write destination drive with ImageMixer 3.
Cautions for use About this unit ≥ The unit, disc and card become warm after long operation, but this is not a malfunction. Keep the DVD Video Camera as far away as possible from electromagnetic equipment (such as microwave ovens, TVs, video games etc.).
Others ≥ This unit is not intended for industrial use. When you are not going to use the unit for an extended time ≥ When storing the unit in a cupboard or cabinet, it is recommended that you place a desiccant (silica gel) in with it.
About the disc ≥ If there is dust, a scratch, or dirt on disc or if it is warped, the following phenomena may occur: jBlock noise in playback image jMomentary stop of playback image jSound interrupted during playback, or abnormal sound jScenes are displayed as [ thumbnail display jDisc cannot correctly be recognized...
Others About condensation When condensation forms on the unit, the lens will cloud up and the unit may not work properly. Make every effort to ensure that condensation does not form. If it does form, take the actions described below. Causes of condensation Condensation takes place when the ambient temperature or humidity is changed as...
source. For light outside the functional automatic white balance adjustment range, use the manual white balance adjustment mode. White balance The images recorded by the unit may become bluish or reddish under the influence of certain light sources. To avoid such phenomena, adjust the white balance.
Others Specifications DVD Video Camera Information for your safety Power source: Power consumption: Signal system Recording format Image sensor Lens Filter diameter Zoom Monitor Viewfinder Microphone Speaker Standard illumination LSQT1145 DC 7.9 V/7.2 V Recording 7.0 W (VDR-D310)/6.0 W (VDR-D230/VDR-D210) EIA Standard: 525 lines, 60 fields NTSC color signal DVD Video Recording format (DVD-RAM, DVD-RW) DVD-Video format (DVD-RW, DVD-R, DVD-R DL)
Page 139
Minimum required illumination Video output level S Video output level (VDR-D310/VDR-D230) Audio output level (Line) Mic input (VDR-D310) (VDR-D310/VDR-D230) Dimensions (excluding the projecting parts) Mass (without battery, lens cap and a disc) Operating temperature Operating humidity Motion pictures Recording media Compression Recording mode and transfer rate...
Page 140
Others Picture size AC adaptor Information for your safety Power source: Power consumption: DC output: Dimensions Mass Specifications may change without prior notice. LSQT1145 VDR-D310: 2048k1512, 1920k1080 (16:9), 1280k960, 640k480 VDR-D230: 640k480, 640k360 (16:9) AC 110 V to 240 V, 50/60 Hz 19 W DC 7.9 V, 1.4 A (Unit operation) DC 8.4 V, 0.65 A (Battery charging)
Optional accessories Some optional accessories may not be available in some countries. Accessory No. LM-AF30U LM-AF60U LM-RW30U LM-RW60U LM-RF30V LM-RF60V LM-RF55LV PV-DAC14 CGR-DU06A/1B* (VDR-D230/VDR-D210) CGA-DU12A/1B* CGA-DU21A/1B* RP-SDR04GU1K RP-SDR02GU1A RP-SDR01GU1A RP-SDR512U1A RP-SDR256U1A RP-SDK02GU1A RP-SDH01GU1A RP-SDK512U1A RP-SDH256U1A RP-SDV04GU1K RP-SDV02GU1A RP-SDV01GU1A RP-SS01GU1K RP-SS512BU1K RP-SS256BU1K VW-LDC10 * Please refer to page 29 concerning the battery charging time and available recording time.
VISIT YOUR LOCAL PANASONIC DEALER CALL PANASONIC’S ACCESSORY ORDER LINE AT 1-800-332-5368 MAIL THIS ORDER TO: PANASONIC SERVICE AND TECHNOLOGY COMPANY In CANADA, please contact your local Panasonic dealer for more information on Accessories. LSQT1145 P rice Each Your State & Local Sales Tax Shipping &...
Request for Service Notice: Mail this completed form and your Proof of Purchase along with your unit to: Panasonic Camera and Digital Service Center • Please include your proof of purchase. (Failure to do so will delay your repair.) •...
If your product does not work properly because of a defect in materials or workmanship, Panasonic Consumer Electronics Company or Panasonic Puerto Rico, Inc. (collectively referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (“warranty period”), at its option either (a) repair your product with new or refurbished...
1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST For hearing or speech impaired TTY users, TTY : 1-877-833-8855 Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at: http://www.pstc.panasonic.com or, send your request by E-mail to: npcparts@us.panasonic.com...
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 PANASONIC PRODUCT – LIMITED WARRANTY Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship and agrees to remedy any such defect for a period as stated below from the date of original purchase.
Others Spanish Quick Use Guide/ Guía española para el uso rápido ∫ Carga de la batería Conecte el cable eléctrico de CA al adaptador de CA y a la toma de la red de Meta la batería en el respectivo soporte alineando la marca, luego encájela.
Page 152
Others ∫ Cómo insertar/quitar una tarjeta SD (VDR-D310/VDR-D230) Deslice la tapa de la ranura para tarjetas para abrirla. Inserte/quite la tarjeta SD en/de la ranura de la tarjeta. Cierre firmemente la tapa de la ranura de la tarjeta. ∫ Grabación de imágenes dinámicas ≥...
Page 153
VDR-D310: Pulse el botón de toma fotográfica [ medias para enfocar al sujeto. (Solo en el modo de enfoque automático) Pulse completamente el botón de toma fotográfica [ ] para tomar la foto. VDR-D230: Pulse el botón de toma fotográfica [ ∫...
Page 154
Others Pulse el joystick. Mueva el joystick para obrar. 1/;: La exposición de diapositivas inicia/se interrumpe. Reproduce la imagen anterior. Reproduce la imagen siguiente. Detiene la reproducción y muestra las ∫: miniaturas. LSQT1145...
Page 156
Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America One Panasonic Way, Secaucus, NJ 07094 Panasonic Puerto Rico, Inc. Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985 Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3...