EXPLOSÈES ET LES LISTES DE PIECES SONT D’UNE IMPOR-TANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT, NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT LE NUMÈRO DE PIÈCE EST INDIQUÈ DANS LE PRÈSENT MANUEL OU DANS DES SUPPLÈMENTS PUBLIÈS PAR SONY.
Page 3
2 (C Board) The servicing of these boards requires special precautions to be taken as outlined below: 1. It is strongly recommended to use Sony Approved Lead Free Solder material in order to guarantee optimal quality of new solder joints.
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 SELF DIAGNOSTIC FUNCTION The units in this manual contain a self diagnostic function. If an error occurs, the STANDBY (1) indicator will automatically begin to flash. A description of the self-diagnosis function is explained in the instruction manual. The number of times the STANDBY (1) indicator flashes translates to a probable source of the problem.
Page 5
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 2. DISPLAY OF INDICATOR STANDBY (1) FLASH COUNT Diagnostic Item Flash Count* +B overcurrent 2 times V-Protect 4 times IK (AKB) 5 times HV Protect 8 times * One flash count is not used for self-diagnosis. Lamp ON 300ms...
Page 6
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. When you have completed the repairs, clear the result display to “0”. Unless the result display is cleared to “0”, the self-diagnosis function will not be able to detect subsequent faults after completion of the repairs.
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 1-7. PICTURE TUBE REMOVAL Note: • Please make sure the TV set is not in standing position before removing necessary CRT support located on bottom right and left. 1) Place the TV set with the CRT face down on a cushion jig.
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 SECTION 2 SET-UP ADJUSTMENTS • The following adjustments should be made when a Perform the adjustments in the following order : complete realignment is required or a new picture tube is 1. Beam Landing installed. 2. Convergence 3. Focus Set the controls as follows unless otherwise noted: 4.
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 4. If the H.STAT variable resistor cannot bring the red, 2-2. CONVERGENCE green and blue dots together at the centre of the Preparation: screen, adjust the horizontal convergence with the H. • Before starting this adjustment, adjust the focus, STAT variable resistor and the V.STAT magnet in the...
Page 11
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 H-TILT correction can be performed by adding a TLH 5. Layout of each control. correction assembly to the Deflection Yoke. V.STAT Purity 8. YCH Adjustment BMC (Hexapole) YCH VR Deflection Yoke 9. TLV Adjustment 6. Geometry Adjustment. TLV VR...
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 2-3. FOCUS ADJUSTMENT 2-5. WHITE BALANCE ADJUSTMENT 1. Receive digital monoscope pattern. 1. Enter into Service Menu. 2. Set Picture Mode to PERSONAL. 2. Input white pattern signal. 3. Adjust focus VR to obtain the best focus at the centre of 3.
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 SECTION 3 CIRCUIT ADJUSTMENTS 3-1. ADJUSTMENT WITH COMMANDER Service adjustment to this model can be performed using the supplied remote commander RM-W100. a. ENTERING SERVICE MODE With the unit on standby, press the following sequence of buttons on the remote commander.
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 NOTE • shaded items are adjustable data. • no data. • Standard data listed on the Adjustment Item Table are reference values, therefore it may be different for each model and for each mode. • Note for Different Data: Those are the standard data values written on the microprocessor. Therefore, the data values of the modes are stored respectively in the memory.
Page 23
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 OPB6 Item GA US Latin Feature 2 Feature 1 OSD Language Selection KV-14CT1B KV-14CT1U KV-14CT1E KV-14CT1K GA US (US Model Destination) 0 = US/Canada/Latin, 1 = Taiwan/Korea/Philippine Latin (US Model Latin Destination) 0 = US/Canada (No Volume Figure Display)
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 Set NVM as non-virgin 3-3. T-MODE: Set NVM as virgin T-Mode is available by pressing the 'TEST' button once, Auto AGC Adjustment OSD 'T' appears. The function described below are available by selecting the indicated keys. The 'T' is released RGB priority (toggle) automatically after each command is executed.
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 3-6. SUB BRIGHTNESS ADJUSTMENT 3-8. SUB COLOUR ADJUSTMENT 1. Input a PAL monoscope pattern. 1. Receive a PAL colour bar signal. 2. Go to Test Mode. 2. Connect an oscilloscope to Pin 2 of CN004(A board). 3. Press 'Test' 'Test 13' on the Remote commander.
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 3-10. DEFLECTION ADJUSTMENT Vertical Amplitude (VSIZ) 1. Set the TV mode to normal (4:3). 2. Enter into the 'GEOMETRY' service menu. 3. Select and adjust each item in order to obtain the optimum image. (see table below) Vertical Linearity (VLIN) 4.
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 4-2. CIRCUIT BOARDS LOCATION C board A Board 4-3. SCHEMATIC DIAGRAM Reference information Note: All capacitors are in µF unless otherwise noted. RESISTOR : RN METAL FILM • • All electrolytic capacitors are rated at 50V unless otherwise noted.
Page 40
KV-14CT1B/14CT1U/14CT1E/14CT1K KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 RM-W100 NOTE: The circuit indicated at left contains high voltage of over PRINTED WIRING BOARDS 1220 Vp-p. Please pay attention when inspecting or repairing it to prevent an electric shock. [PROCESSOR, AUDIO, POWER SUPPLY, DEFLECTION, TUNER, JACK, SCART TERMINAL] –...
LOUD SPEAKER (5 x 9 CM) * 4-092-231-01 GUIDE, LIGHT 4-094-690-01 PIECE A (90) CONV, CORRECT 4-092-229-01 DOOR CONTROL * A-1302-283-A COMPLETE PWB, A (KV-14CT1B) 4-092-230-01 BUTTON POWER * A-1302-405-A COMPLETE PWB, A (KV-14CT1E/1K) 4-036-405-71 SPRING COMPRESSION * A-1302-428-A COMPLETE PWB, A (KV-14CT1U)
REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK * A-1302-283-A COMPLETE PWB, A (KV-14CT1B) C052 1-162-964-11 CERAMIC CHIP 0.001UF 10.00% 50V * A-1302-405-A COMPLETE PWB, A (KV-14CT1E/1K) C053 1-164-227-11 CERAMIC CHIP 0.022UF 10.00% 25V...
Page 45
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK C210 1-126-968-11 ELECT 100UF 20.00% 50V C653 1-102-228-00...
Page 46
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK C882 1-106-363-00 MYLAR 0.0068UF 99% 200V D074 8-719-081-97...
Page 47
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK D915 8-719-069-55 DIODE UDZSTE-175.6B JR012 1-216-864-11 SHORT CHIP...
Page 48
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK L013 1-469-525-91 INDUCTOR 10UH Q807 8-729-010-05 MSB709-RT1 L031...
Page 49
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK R154 1-216-864-11 SHORT CHIP R401 1-260-288-11 CARBON 0.47...
Page 50
KV-14CT1B/14CT1U/14CT1E/14CT1K RM-W100 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK R854 1-218-877-11 METAL CHIP 0.5% 1/10W R9023 1-216-809-11...
Page 51
DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK <COIL> VARIANT PARTS LIST L780 1-410-667-31 INDUCTOR 22UH <SWITCH> SWF102 1-767-083-11 FILTER, SURFACE WAVE (KV-14CT1B) <RESISTOR> R713 1-216-864-11 SHORT CHIP <TUNER> R752 1-216-819-11 METAL CHIP 1/10W R753 1-216-819-11 METAL CHIP 1/10W TU101...
Page 71
Les principaux émetteurs français EMETTEURS CANAUX CANAL+ ARTE 65 MARSEILLE Grande Etoile 66 MARSEILLE Pomègues 67 MAUBEUGE Rousies 68 MENDE Truc de Fortino 37/31 69 MENTON Cap Martin 70 MELZ Luttange 71 MEZIERES Sury 72 MILLAU Levezou 73 MONTLUCON "Maregnon" 74 MONNETTIER MORNEX Mont Saléve 75 MONTMELLIAN Le Fort 76 MONTPELLIER Saint-Baudille...
Page 72
Les principaux émetteurs français 5pSDUWLWLRQ (XURSpHQQH GHV QRUPHV HW VWDQGDUGV SECAM Informations complémentaires...
Introducción Gracias por elegir este televisor en color Sony de Pantalla Plana FD Trinitron. Antes de utilizar el televisor, lea este manual atentamente y consérvelo para futuras referencias. Símbolos utilizados en este manual: • Información importante. • Los botones sombreados del mando a distancia, muestran los botones que •...
Normas de Seguridad Nunca introduzca objetos ni Por razones medioambientales y derrame ningún tipo de líquido Este aparato sólo debe utilizarse de seguridad, se recomienda no dentro del aparato ya que podría con fuentes de alimentación de dejar el aparato en modo de 220-240 V CA.
Descripción general de los botones del mando a distancia Apagar temporalmente el televisor Mostrar información en pantalla Púlselo para apagar temporalmente el televisor (el indicador Púlselo para mostrar todas las de modo de espera 1 se iluminará). Vuelva a pulsarlo para indicaciones en pantalla.
Descripción general de los botones del televisor Botones de selección Activación Botón de Botones de selección de la de programas del sistema control del fuente de volumen siguiente o anterior de menús entrada (seleccionan emisoras de televisión) Toma de Toma de Toma de entrada de auriculares...
Conexión de una antena portátil (sólo para KV-14CT1E) Para obtener una mejor recepción de imagen, le recomendamos que conecte el televisor a una antena exterior. No obstante, si no dispone de antena exterior pero la señal local de VHF/UHF es lo suficientemente fuerte, puede conectar la antena telescópica suministrada con este televisor tal y como se indica a continuación: inserte la antena en la ranura situada en la parte superior del televisor hasta que ésta haga “clic”.
Encendido y Sintonización automática del TV La primera vez que encienda el televisor, aparecerá en la pantalla una secuencia de menús a través de los cuales podrá: 1) seleccionar el idioma de los menús, 2) seleccionar el país donde desea utilizar el aparato, 3) buscar y almacenar automáticamente todos los canales disponibles (emisoras de televisión) 4) cambiar el orden en que los canales (emisoras de televisión) aparecen en pantalla y 5) ajustar la inclinación de la imagen (sólo para KV-21CT1E).
Page 80
Una vez que el televisor ha sintonizado y memorizado todos los Ordenación de Programas canales (emisoras de televisión), en pantalla aparece Programa: automáticamente el menú Ordenación de Programas para que TVE2 pueda cambiar el orden en que los canales aparecen en la pantalla. Si no desea cambiar el orden de los canales, pulse MENU.
Introducción y manejo del sistema de menús Este televisor utiliza un sistema de menús en pantalla para guiarle en las diferentes operaciones. Utilice los siguientes botones del mando a distancia para desplazarse a través de los menús: Pulse el botón MENU para mostrar el primer nivel de menú en pantalla. •...
Tonalidad Pulse para aminorar los tonos verdes. Pulse para incrementar los tonos verdes. Tonalidad no se puede ajustar para la señal de color NTSC (p.ej. vídeos de los EE.UU.). Nitidez Pulse para atenuar la imagen. Pulse para avivar la imagen. Seleccione para restablecer la imagen a los niveles Preestablecido...
Temporizador El menú “Temporizador” le permite Temporizador Temporizador modificar los ajustes del Desconex. Aut.: Desconex. Aut.: Conexión Aut.: Conexión Aut.: temporizador. Sel. Confirmar Sel. Confirmar Desconexión La opción de “Desconex. Aut.” dentro del menú “Temporizador”, le permite seleccionar un periodo de tiempo tras el cual el televisor Automática entrará...
Ajuste de canales El menú "Ajuste de canales" permite Ajuste de canales Ajuste de canales memorizar los canales de este Sintonía Automática Sintonía Automática Ordenación de Programas Ordenación de Programas televisor. Etiquetado de Programas Etiquetado de Programas Sintonía Manual Sintonía Manual Sel.
Page 85
Sintonía Manual La opción de “Sintonía Manual” dentro del menú “Ajuste de canales”, le permite: a) Sintonizar uno a uno y en el orden de programa que desee, los canales (emisoras de televisión) o una entrada de vídeo. Para ello: Tras seleccionar la opción de “Sintonía Manual”, pulse .
Configuracíon El menu “Configuracíon“ le permite Configuración Configuración modificar algunas de las Idioma/País Idioma/País configuraciones de este televisor. Rotación Imagen Rotación Imagen Centrado RGB: Centrado RGB: Sel. Confirmar Sel. Confirmar Idioma/País La opción de “Idioma/País” dentro del menú “Configuración”, le permite seleccionar el idioma en que desea que aparezcan los menús en la pantalla.
Teletexto Teletexto es un servicio de información que transmiten la mayoría de las emisoras de televisión. La página de índice del servicio de teletexto (página 100 por lo general) proporciona información sobre cómo utilizar este servicio. Para operar dentro del teletexto, utilice los botones del mando a distancia tal y como se indica en esta página.
Entertainment, Inc. desconectarán * “PlayStation” es una marca automáticamente registrada de Sony Computer Entertainment, Inc. Conexión de un vídeo: Para conectar un vídeo, consulte el capítulo “Conexión de una antena exterior y del vídeo”. Le aconsejamos que conecte el vídeo utilizando un cable de Euroconector. Si no utiliza este cable, tendrá...
Especificaciones El sistema de recepción de señales de estos televisores, cumplen la normativa requerida por la ley española del Real Decreto 1160/89. Sistema de TV: Salida de sonido: Dependiendo del país que haya seleccionado: 1 x 6 W (potencia musical) B/G/H, D/K 1 x 3 W (RMS) Sistema de color:...
• Cambie las pilas. El indicador de modo de espera 1 • Póngase en contacto con el servicio técnico de Sony parpadeará en rojo en el televisor. más cercano. En caso de averías, haga que personal especializado examine el televisor.
If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service centre. How to replace the fuse Open the fuse compartment with a blade screwdriver, and replace the fuse.
Page 93
Introduction Thank you for choosing this Sony FD Trinitron Colour Television. Before operating the TV, please read this manual thoroughly and retain it for future reference. Symbols used in the manual: • Important information. • Shaded buttons on the remote control show you the buttons you •...
Safety Information Never push objects of any kind For environmental and safety into the set as this could result in This set is to operate on a 220- reasons, it is recommended that a fire or electric shock. Never 240V AC supply only. Take care the TV set is not left in standby spill liquid of any kind on the not to connect too many...
Overview of Remote Control Buttons Displaying on screen To temporarily switch off TV information Press to temporarily switch off TV (the standby Press to display all on-screen indicator 1 on TV lights up). Press again to switch on indications. Press again to TV from standby mode.
Overview of TV Buttons Volume Selecting Programme Up or Displaying control Input Down buttons the menu buttons source (selects TV system channels) Video Input Headphone Audio Input Lift up the door Standby On/Off jack jack jack flap with indicator switch mark to reveal the control panel.
Connecting an Indoor Aerial (only for KV-14CT1U) For a better reception we recommend you connect an external aerial. However, where an external aerial is not available and your local UHF signal is strong, you can connect the supplied loop aerial as follows: Insert the loop aerial into the opening on top of the set until it clicks.
Switching On the TV and Automatically Tuning The first time you switch on your TV, a sequence of menu screens appear on the TV enabling you to: 1) choose the language of the menu screen, 2) search and store all available channels (TV Broadcast), 3) change the order in which the channels (TV Broadcast) appear on the screen and 4) adjust the picture slant (only for KV-21CT1U).
Page 99
After all available channels are captured and stored, the Programme Sorting Programme Sorting menu appears automatically on the screen Programme: enabling you to change the order in which the channels appear on TVE2 the screen. If you wish to keep the broadcast channels in the tuned order, Select channel Confirm [ t ] Exit Select [ –...
Introducing and Using the Menu System Your TV uses an on-screen menu system to guide you through the operations. Use the following buttons on the Remote Control to operate the menu system: Press MENU to switch the menu on. • To highlight the desired menu or option, press •...
Press to decrease the green tones. Press to increase the green tones. Hue can only be adjusted for NTSC colour signal (e.g. USA video tapes). Sharpness Press to soften the picture. Press to sharpen the picture. Reset Select to reset the picture to the factory preset levels. Intelligent On/Off Select to optimize the picture quality.
Timer The “Timer” menu allows you to alter Timer Timer the timer adjustments. Sleep Timer: Sleep Timer: On Timer: On Timer: Select Confirm Select Confirm Sleep Timer The “Sleep Timer” option in the “Timer” menu allows you to select a time period for the TV to switch itself automatically into the standby mode.
Channel Set Up The “Channel Set Up” menu allows Channel Set Up Channel Set Up you to preset channels on this TV. Auto Tuning Auto Tuning Programme Sorting Programme Sorting Programme Labels Programme Labels Manual Programme Preset Manual Programme Preset Confirm Select Confirm...
Page 104
Manual The “Manual Programme Preset” option in the “Channel Set Up” Programme menu allows you to: a) Preset channels or a video input source one by one to the Preset programme order of your choice. To do this: After selecting the “Manual Programme Preset” option, press .
Set Up The “Set Up” menu allows you to Set Up Set Up alter various options on this TV. Language Language Picture Rotation Picture Rotation RGB Centring: RGB Centring: Confirm Select Confirm Select Language The “Language” option in the “Set Up” menu allows you to select the language that the menus are displayed in.
Teletext Teletext is an information service transmitted by most TV stations. The index page of the Teletext service (usually page 100) gives you information on how to use the service. To operate Teletext, use the remote control buttons as indicated below. Be sure to use a channel (TV Broadcast) with a strong signal, otherwise Teletext errors may occur.
TV set (connecting cables are not supplied). 8mm/Hi8/ DVD/VCR camcorder “PlayStation”* decoder * “PlayStation” is a product When you connect the of Sony Computer headphones, the TV Entertainment, Inc. speakers will * “PlayStation” is a trademark automatically be muted of Sony Computer Entertainment, Inc.
Specifications TV system: Sound Output: 1 x 6 W (music power) 1 x 3 W (RMS) Colour system: Power Consumption: PAL, SECAM NTSC 3.58, 4.43 (only Video In) • KV-21CT1U: 56 W • KV-14CT1U: 50 W Channel Coverage: Standby Power Consumption: UHF B21-B69 <...
Remote control does not function. • Replace the batteries. The standby indicator 1 on the TV • Contact your nearest Sony service centre. flashes red. In case of problems, have your TV serviced by qualified personnel. Never open the casing yourself.
Television Channel Number Guide for United Kingdom Only the main transmitters are listed. Information regarding the regional sub-relay channel numbers can be obtained by contacting The BBC Engineering Information Dept., Telephone Number 020 7852 5040. Additional Information...
Page 114
KV-21CT1U Sony España, S.A. Printed in Spain...
Page 116
Introduction Thank you for choosing this Sony FD Trinitron Colour Television. Before operating the TV, please read this manual thoroughly and retain it for future reference. Symbols used in the manual: • Important information. • Shaded buttons on the remote control show you the buttons you have to •...
Safety Information Never push objects of any kind For environmental and safety into the set as this could result in This set is to operate on a 220- reasons, it is recommended that a fire or electric shock. Never 240V AC supply only. Take care the TV set is not left in standby spill liquid of any kind on the not to connect too many...
Overview of Remote Control Buttons Displaying on screen To temporarily switch off TV information Press to temporarily switch off TV (the standby Press to display all on-screen indicator 1 on TV lights up). Press again to switch on indications. Press again to TV from standby mode.
Overview of TV Buttons Volume Selecting Programme Up or Displaying Input control Down buttons the menu source buttons (selects TV system channels) Video Input Headphone Audio Input jack jack jack Standby On/Off Lift up the door indicator switch flap with mark to reveal the control panel.
Connecting an Indoor Aerial (only for KV-14CT1K) For a better reception we recommend you connect an external aerial. However, where an external aerial is not available and your local VHF/UHF signal is strong, you can connect the supplied indoor aerial as follows: Insert the aerial into the opening on top of the set until it clicks.
Switching On the TV and Automatically Tuning The first time you switch on your TV, a sequence of menu screens appear on the TV enabling you to: 1) choose the language of the menu screen, 2) choose the country in which you wish to operate the TV, 3) search and store all available channels (TV Broadcast), 4) change the order in which the channels (TV Broadcast) appear on the screen and 5) adjust the picture slant (only for KV-21CT1K).
Page 122
After all available channels are captured and stored, the Programme Sorting Programme Sorting menu appears automatically on the screen Programme: enabling you to change the order in which the channels appear on TVE2 the screen. If you wish to keep the broadcast channels in the tuned order, Select channel Select [ –...
Introducing and Using the Menu System Your TV uses an on-screen menu system to guide you through the operations. Use the following buttons on the Remote Control to operate the menu system: Press MENU to switch the menu on. • To highlight the desired menu or option, press •...
Press to decrease the green tones. Press to increase the green tones. Hue can only be adjusted for NTSC colour signal (e.g. USA video tapes). Sharpness Press to soften the picture. Press to sharpen the picture. Reset Select to reset the picture to the factory preset levels. Intelligent On/Off Select to optimize the picture quality.
Timer The “Timer” menu allows you to alter Timer Timer the timer adjustments. Sleep Timer: Sleep Timer: On Timer: On Timer: Select Confirm Select Confirm Sleep Timer The “Sleep Timer” option in the “Timer” menu allows you to select a time period for the TV to switch itself automatically into the standby mode.
Channel Set Up The “Channel Set Up” menu allows Channel Set Up Channel Set Up you to preset channels on this TV. Auto Tuning Auto Tuning Programme Sorting Programme Sorting Programme Labels Programme Labels Manual Programme Preset Manual Programme Preset Select Confirm Select...
Page 127
Manual The “Manual Programme Preset” option in the “Channel Set Up” Programme menu allows you to: a) Preset channels or a video input source one by one to the Preset programme order of your choice. To do this: After selecting the “Manual Programme Preset” option, press .
Set Up The “Set Up” menu allows you to Set Up Set Up alter various options on this TV. Language/Country Language/Country Picture Rotation Picture Rotation RGB Centring: RGB Centring: Select Confirm Select Confirm The “Language/Country” option in the “Set Up” menu allows you to Language/ Country select the language that the menus are displayed in.
Teletext Teletext is an information service transmitted by most TV stations. The index page of the Teletext service (usually page 100) gives you information on how to use the service. To operate Teletext, use the remote control buttons as indicated below. Be sure to use a channel (TV Broadcast) with a strong signal, otherwise Teletext errors may occur.
TV set (connecting cables are not supplied). 8mm/Hi8/ DVD/VCR camcorder “PlayStation”* decoder * “PlayStation” is a product When you connect the of Sony Computer headphones, the TV speakers will Entertainment, Inc. * “PlayStation” is a trademark automatically be muted of Sony Computer Entertainment, Inc.
Specifications TV system: Sound Output: Depending on your country selection: 1 x 6 W (music power) B/G/H, D/K 1 x 3 W (RMS) Colour system: Power Consumption: PAL, SECAM • KV-21CT1K: 56 W NTSC 3.58, 4.43 (only Video In) • KV-14CT1K: 50 W Channel Coverage: Standby Power Consumption: VHF:...
Remote control does not function. • Replace the batteries. The standby indicator 1 on the TV • Contact your nearest Sony service centre. flashes red. In case of problems, have your TV serviced by qualified personnel. Never open the casing yourself.
If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service centre. How to replace the fuse Open the fuse compartment with a blade screwdriver, and replace the fuse.
Page 135
Introduction Thank you for choosing this Sony FD Trinitron Colour Television. Before operating the TV, please read this manual thoroughly and retain it for future reference. Symbols used in the manual: • Important information • Shaded buttons on the remote control show you the buttons you have to •...
Safety Information Never push objects of any kind For environmental and safety into the set as this could result in This set is to operate on a 220- reasons, it is recommended that a fire or electric shock. Never 240V AC supply only. Take care the TV set is not left in standby spill liquid of any kind on the not to connect too many...
Overview of Remote Control Buttons Displaying on screen To temporarily switch off TV information Press to temporarily switch off TV (the standby Press to display all on-screen indicator 1 on TV lights up). Press again to switch on indications. Press again to TV from standby mode.
Overview of TV Buttons Selecting Programme Up or Displaying Volume Input Down buttons the menu control source (selects TV system buttons channels) Video Input Headphone Audio Input jack jack jack Lift up the door Standby On/Off flap with indicator switch mark to reveal the control panel.
Connecting an Indoor Aerial (only for KV-14CT1B) For a better reception we recommend you connect an external aerial. However, where an external aerial is not available and your local VHF/UHF signal is strong, you can connect the supplied indoor aerial as follows: Insert the aerial into the opening on top of the set until it clicks.
Switching On the TV and Automatically Tuning The first time you switch on your TV, a sequence of menu screens appear on the TV enabling you to: 1) choose the language of the menu screen, 2) choose the country in which you wish to operate the TV, 3) search and store all available channels (TV Broadcast), 4) change the order in which the channels (TV Broadcast) appear on the screen and 5) adjust the picture slant (only for KV-21CT1B).
Page 141
After all available channels are captured and stored, the Programme Sorting Programme Sorting menu appears automatically on the screen Programme: enabling you to change the order in which the channels appear on TVE2 the screen. If you wish to keep the broadcast channels in the tuned order, Select channel Select [ –...
Introducing and Using the Menu System Your TV uses an on-screen menu system to guide you through the operations. Use the following buttons on the Remote Control to operate the menu system: Press MENU to switch the menu on. • To highlight the desired menu or option, press •...
Press to decrease the green tones. Press to increase the green tones. Hue can only be adjusted for NTSC colour signal (e.g. USA video tapes). Sharpness Press to soften the picture. Press to sharpen the picture. Reset Select to reset the picture to the factory preset levels. Intelligent On/Off Select to optimize the picture quality.
Timer The “Timer” menu allows you to alter Timer Timer the timer adjustments. Sleep Timer: Sleep Timer: On Timer: On Timer: Select Confirm Select Confirm Sleep Timer The “Sleep Timer” option in the “Timer” menu allows you to select a time period for the TV to switch itself automatically into the standby mode.
Channel Set Up The “Channel Set Up” menu allows Channel Set Up Channel Set Up you to preset channels on this TV. Auto Tuning Auto Tuning Programme Sorting Programme Sorting Programme Labels Programme Labels Manual Programme Preset Manual Programme Preset Select Confirm Select...
Page 146
Manual The “Manual Programme Preset” option in the “Channel Set Up” Programme menu allows you to: a) Preset channels or a video input source one by one to the Preset programme order of your choice. To do this: After selecting the “Manual Programme Preset” option, press .
Set Up The “Set Up” menu allows you to Set Up Set Up alter various options on this TV. Language/Country Language/Country Picture Rotation Picture Rotation RGB Centring: RGB Centring: Select Confirm Select Confirm Language/ The “Language/Country” option in the “Set Up” menu allows you to Country select the language that the menus are displayed in.
Teletext Teletext is an information service transmitted by most TV stations. The index page of the Teletext service (usually page 100) gives you information on how to use the service. To operate Teletext, use the remote control buttons as indicated below. Be sure to use a channel (TV Broadcast) with a strong signal, otherwise Teletext errors may occur.
TV set (connecting cables are not supplied). 8mm/Hi8/ DVD/VCR camcorder “PlayStation”* decoder * “PlayStation” is a product When you connect the of Sony Computer headphones, the TV Entertainment, Inc. speakers will * “PlayStation” is a trademark automatically be muted of Sony Computer Entertainment, Inc.
E21-E69 Dimensions (w x h x d): CATV: S1-S20 • KV-21CT1B: Approx. 497 x 461 x 487 mm HYPER: S21-S41 • KV-14CT1B: Approx. 374 x 355 x 420 mm F2-F10, B-Q, F21-F69 UHF B21-B69 Weight: D/K: R1-R12, R21-R69 • KV-21CT1B: Approx. 24 kg •...
Remote control does not function. • Replace the batteries. The standby indicator 1 on the TV • Contact your nearest Sony service centre. flashes red. In case of problems, have your TV serviced by qualified personnel. Never open the casing yourself.
Page 152
KV-21CT1B Sony España, S.A. Printed in Spain...