When Q1103 or Q1104 is shorted between their terminals, the laser diodes for DVD or CD will radiate beam. If the top cover is removed with no disc loaded while such short-circuit is continued, the naked eyes may be exposed to the laser beam. AVH-P3200BT/XNUC...
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. AVH-P3200BT/XNUC...
How to enter : Press RESET while pressing [FORWARD] and [EJECT] keys together. How to exit : Same procedure to enter this mode. 10. When EEPROM is initialized, eject lock may be enabled. Please cancel eject lock in this case. AVH-P3200BT/XNUC...
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. AVH-P3200BT/XNUC...
2. SPECIFICATIONS 2.1 SPECIFICATIONS AVH-P3200BT/XNUC, AVH-P3200DVD/XNUC Equalizer (8-Band Graphic Equalizer): General Frequency......40/80/200/400/1k/2.5k/8k/ Power source......14.4 V DC (10.8 V to 15.1 V 10k Hz allowable) Gain ........±12 dB Grounding system....Negative type HPF: Maximum current consumption Frequency......50/63/80/100/125 Hz ............10.0 A...
Page 8
Frequency range..... 530 kHz to 1 710 kHz (10 kHz) Usable sensitivity....25 μV (S/N: 20 dB) Signal-to-noise ratio....62 dB (IEC-A network) Bluetooth (AVH-P3200BT) Version ........Bluetooth 2.0 certified Output power ......+4 dBm Max. (Power class 2) CEA2006 Specifications Power output ......14 W RMS ×...
Page 9
(Ver. 8.2 and earlier) Slope........–12 dB/oct DivX decoding format....Home Theater Ver. 3, 4, 5.2, Subwoofer (mono): 6 (.avi, .divx) Frequency......50/63/80/100/125 Hz Slope........–18 dB/oct Gain ........+6 dB to – 24 dB Phase .........Normal/Reverse Bass boost: Gain ........+12 dB to 0 dB AVH-P3200BT/XNUC...
Page 10
Version ........Bluetooth 2.0 certified Output power ......+4 dBm Max. (Power class 2) Infrared remote control Wavelength....... 945 nm Output ......... typ; 10 mw/sr per Infrared Note Specifications and the design are subject to mod- ifications without notice. AVH-P3200BT/XNUC...
(BT model only) The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Pioneer Corporation is under license. Other trademarks and trade names are those of their respective owners. AVH-P3200BT/XNUC...
2.3 PANEL FACILITIES Head unit CAUTION • Use an optional Pioneer USB cable (CD-U50E) to connect the USB audio player/USB mem- ory as any device connected directly to the unit will protrude out from the unit and may 4 4 4 4 4 4 4 be dangerous.
Press to stop play- REAR SRC sources. back. Press and hold to turn the rear source off. Press to select the next/previous disc/ folder. / (FOLDER/P.CH) Press to recall radio station frequencies as- signed to preset tun- ing keys. AVH-P3200BT/XNUC...
3.2 PCB LOCATIONS DVD Core Unit Connect PCB SD PCB Interface PCB BT ANT PCB Keyboard PCB Mother Unit Monitor PCB P:AVH-P3200BT/XNUC Q:AVH-P3250BT/XNRD J:AVH-P3200DVD/XNUC K:AVH-P3250DVD/XNRC L:AVH-P3250DVD/XNRD M:AVH-P3250DVD/XNRI Unit Number Unit Number Unit Number Unit Number Unit Number Unit Number Unit Name...
Skew adjustment (1530:produced by THREE BOND) 3.4 CLEANING Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools DVD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 AVH-P3200BT/XNUC...
4. BLOCK DIAGRAM Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST". IP BUS model P : AVH-P3200BT/XNUC Q : AVH-P3250BT/XNRD JA2504 JA2503 CKS3414-A YKS5001-E J : AVH-P3200DVD/XNUC K : AVH-P3250DVD/XNRC...
ASENBO <- H DDCCLK <- Clock Out DDCCLK : Pin92 (Frequency of 370 kHz) VD5 <- H VD5, 8 : Pin113, 114 VD8 <- H Starts Communication with Display microcomputor Source Keys operartive Source ON SYSPW : Pin130 SYSPW <- H AVH-P3200BT/XNUC...
Perform lens Is it OK? cleaned? cleaning Replace the PICK UP Check point: Error rate check Error rate check PICK UP Perform lens Is it OK? cleaned? cleaning Replace the PICK UP Ckeck parts Finished other than PICK UP AVH-P3200BT/XNUC...
Page 36
60 - 390 (mV) 10 - 65 (mA) Expansion NO. Disc Check Point Threshold Remarks: LD current TCD-782 CDLD1-VCC5_3 60 - 360 (mV) 10 - 60 (mA) Expansion Notes: Please pay attention to the laser diode damage by static electricity. AVH-P3200BT/XNUC...
Page 37
GGV1025 ID: 40000 1.000E-03 less than GGV1025 ID: 200000 1.000E-03 less than TCD-782 ID: HOME Position 2.500E-03 Test mode display will not appear on the display of this product. Connect the rear monitor output to a monitor. AVH-P3200BT/XNUC...
Page 39
<Check> Check the voltage at the “STANBY” test point while the power is on. Use the “DGND1” test point at the reference. Specification value Check point Module No. Unit VCC33 V- STANBY-DGND1 0.6 V or more Side A DGND1 STANBY Fig 1.1: STANBY check point AVH-P3200BT/XNUC...
Page 41
<Check> Check the voltage at the “XRES” test point while the power is on. Use the “DGND1” test point at the reference. Check point Module No. Specification value Unit VCC33 × 1 XRES-DGND1 0.7 or more Side A DGND1 NRES Fig 3.1: RESET check point AVH-P3200BT/XNUC...
Page 42
<Check> Check the voltage at the “VSENS” test point while the power is on. Use the “DGND1” test point at the reference. Specification value Check point Module No. Unit 1 VSENS - DGND1 0.95 - 1.07 VD8 = 8.0 ± 0.4 V Side A VSENS DGND1 Fig 4.2: VSENS check point AVH-P3200BT/XNUC...
Page 43
Specification value Check point Module No. Unit 27 MHz 2 IC1501 169pin ± 50 ppm Specification value Fig 5.2: Clock specification value Side A IC1501 158pin DGND1 Fig 5.3: 27 MHz check point AVH-P3200BT/XNUC...
Page 44
Be careful as XCSM, XWE, XCAS and XRAS of IC1480 are called differently in IC1501, namely NCSM, NWE, NCAS, NRAS. IC1501 MA0 - 11 1480 DV5U MDQ0 - 15 SDRAM XWE(NWE) XCAS(NCAS) XRAS(NRAS) XCSM(NCSM) DQM0 DQM1 Fig 6.1: SDRAM I/F AVH-P3200BT/XNUC...
Page 46
Side B Check point 1 (IC1480) Side A Check point 2 (IC1501) Fig 6.2: SDRAM I/F check point AVH-P3200BT/XNUC...
Page 47
Check point Module No. Specification value Unit VD8_1 - PGND3 8.0 ± 0.4 VD - PGND3 8.0 ± 0.4 VCC5_1- AGND1 5.0 ± 0.1 Side A AGND3 VCC5_ 1 PGND1 VD8_ 1 PGND3 Fig 7.2: VD8, VCC5 voltage check points AVH-P3200BT/XNUC...
Page 48
Check with PGND and GNDAU being the reference. Check point Module No. Specification value Unit VD - PGND_3 8.0 ± 0.4 AVCC5 - GNDAU1 5.0 ± 0.1 Side A AVCC5 PGND3 GNDAU1 Fig 8.2: VD8, AVCC5 voltage check points AVH-P3200BT/XNUC...
Page 49
Specification value 3 36.864 0 MHz ± 300 ppm DACCK 2.0 V~VCC33 V DGND~0.8 V DACCK 2.0 V~VCC33 V DGND~0.8 V 33.868 8 MHz ± 300 ppm Specification value 1 Specification Specification value 2 value 3 Fig 9.2: Clock specification value AVH-P3200BT/XNUC...
Page 50
Side B Check point 1 (DACCK stylus) Side A Check point 2 (IC1501 148 pin) DGND2 Fig 9.3: 27 MHz, DACCLK check point AVH-P3200BT/XNUC...
Page 51
Waveform 1 SRCK VCC33 V-0.6 V or higher 0.4 V or lower Waveform 2 LRCK VCC33 V-0.6 V or higher 0.4 V or lower Waveform 3 Specification value 2 Specification value 1 Fig 10.2: Serial 3 lines specification value AVH-P3200BT/XNUC...
Page 52
Side A DGND2 ADOUT LRCK Side B SRCK Fig 10.3: Serial 3 lines check points AVH-P3200BT/XNUC...
Page 53
GNDAU1 Fig 10.5: Analog audio out check point Check with DGND being the reference. Specification value 2 Check point 1 (stylus) Specification value 1 Reference waveform 6 IEC VCC33 V-0.6 V or higher 0.4 V or lower Waveform 5 AVH-P3200BT/XNUC...
Page 54
Side A IEC DGND2 Fig 10.6: Digital audio signal (IECOUT) check point AVH-P3200BT/XNUC...
Page 55
In case of NG, check the applicable line, the periphery of the major components in the drawing above, soldering of the peripheral components and defective components. PEAK Reference COMPOSITE signal value Color burst Pedestal level BOTTOM Horizontal sync signal Fig 11.2: Waveform for the case of composite white 100% output AVH-P3200BT/XNUC...
Page 56
Side A COMPOSITE GNDV Fig 11.3: VIDEO signal check point AVH-P3200BT/XNUC...
Page 57
(Refer to the FE test mode for the method of displaying the LD energizing time.) 2.If the second digit from the left of the energizing time display is showing E, such as “ E ”, it means that the flash memory has reached its life. Example: 0E000BB8 AVH-P3200BT/XNUC...
Page 58
In case of NG, check the applicable line, periphery of IC1501, soldering of the peripheral components and defective components. Specification value Check point Module No. Unit 48 MHz 2 IC1501 50pin-DGND1 ± 50 ppm Specification value Fig 13.2: Clock specification value AVH-P3200BT/XNUC...
Page 59
Side A IC1501 50pin DGND1 Fig 13.3: 48 MHz check point AVH-P3200BT/XNUC...
Page 60
1.USB Memory: Play a song from USB memory and check D+ and D- with the DGND standards. 2.iPod: Connect iPod and check CP_RESET, SDA and SCL with the DGND standards until the pioneer log appears. Play a song from iPod and check D+/D- with the DGND standards.
Page 61
Side A SDATA CP_ RESET SCLOCK DGND2 AVH-P3200BT/XNUC...
CBW and CSW forwarding error ERROR-02-D1 CBW and CSW forwarding error Audio class band securing failure ERROR-02-D8 Audio class band securing failure Audio class FS setting failure ERROR-02-D9 Audio class FS setting failure Undefined Error ERROR-FF-FF Undefined error AVH-P3200BT/XNUC...
Page 66
*5 AWM (Audio WaterMark): Electronic watermark. Information on the copyright owner or CCI (copy control information) are recorded so that illegally copied discs can be identified. *6 Notice as an error status will not be given *7 CPRM(Content Protection for Recordable Media) : A copyright protection technique for digital contents used for re-writable DVD or memory card. (DVD-VR model only) AVH-P3200BT/XNUC...
10. BUSR- REAR AUDIO REAR CAMERA IN 11. BUSL- OUTPUT FRONT OUTPUT VIDEO WIRED REMOTE INPUT/OUTPUT AUX IN(*) REAR OUTPUT CONTROL OPTICAL OUTPUT(*) ANTENNA IN AUDIO INPUT SUBWOOFER OUTPUT OPTICAL OUTPUT AUX IN AVH-P3200BT/XNUC AVH-P3250BT/XNRD AVH-P3200DVD/XNUC AVH-P3250DVD/XNRC AVH-P3250DVD/XNRD AVH-P3250DVD/XNRI AVH-P3200BT/XNUC...
Choose "Version Check" among the monitor test mode menu screen. [Display specifications] When 8 digits of read number is strange, displayed with red. [Operation specification] Operational description Remote controller key Return to test mode mene Page up Page down AVH-P3200BT/XNUC...
Page 71
In case the EEPROM initialization has been performed. In case the adjustment value has been initialized. Calibration inspection : In case the calibration inspection has never been performed. In case the EEPROM initialization has been performed. In case the adjustment value has been initialized. AVH-P3200BT/XNUC...
Page 72
X/Y information of [MIN] and [MAX] of the outermost circumference are displayed. [BEFOR] indicates the value stored in the EEPROM. [AFTER] indicates MIN/MAX of the A/D value currently captured. [Operation specification] Operational description Remote controller key Return to top mene AVH-P3200BT/XNUC...
Page 73
Order of display of the locations to be pressed. This point is intended to end the calibration inspection, and therefore, the corrected value of this point is not obtained. [Operation specification] Operational description Remote controller key Return to top mene AVH-P3200BT/XNUC...
Page 74
: The coordinate (X direction, Y direction) which is the result of adding the correction by calibration to the normalized coordinate is displayed. Movable "+" cursor is displayed in red. 16 calibration points are displayed in white. [Operation specification] Operational description Remote controller key Return to top mene AVH-P3200BT/XNUC...
Page 75
The incorrect touch will make the characters of cursor turn red. Repeat this for 4 points, and “OK” is displayed upon the last press of 4th point. [Display specifications] confirming The pushing order [Operation specification] Operational description Remote controller key Return to top mene AVH-P3200BT/XNUC...
Page 76
When the adjusted value has been initialized (Data initialize). When the EEPROM has been initialized. [Operation specification] Operational description Remote controller key Selection cursor up movement Selection cursor down movement Return to test mode mene Menu enter AVH-P3200BT/XNUC...
Page 77
When normally ends, "success" is displayed. When will not end in four seconds, judged to be abnormal, "failure" is displayed. [Operation specification] Operational description Remote controller key Selection cursor left movement Selection cursor right movement Return to test mode mene Menu enter AVH-P3200BT/XNUC...
Page 78
[MONOCHROME STRIPE] Display of monochrome stripe signal (1dot Width) [Operation specification] Operational description Remote controller key Return to test mode mene [COLOR BAR] Display of color bar signal [Operation specification] Operational description Remote controller key Return to test mode mene AVH-P3200BT/XNUC...
Page 79
Display of Black/White signal [Operation specification] Operational description Remote controller key Return to test mode mene Next signal [CENTER MARKER] Display of signal for screen central location setting. [Operation specification] Operational description Remote controller key Return to test mode mene AVH-P3200BT/XNUC...
In order to F close after focus search (S character measurement mode), set to Power_OFF first then power on again FEMIN level before F close. ASMAX level ENVMAX level FE normalization coefficient Spindle gain coefficient TEMAX level indication TEMIN level indication AVH-P3200BT/XNUC...
Page 81
Designation of digit by command (1) and (2). UP/DOWN of numbers by command (3) and (4). Fix by command (5). Error occurrence at Power_OFF [Note] If an error occurs at Power_OFF, reset cannot be made. In such a case, it is necessary to turn the power off and start the test mode once again. Error display AVH-P3200BT/XNUC...
Page 82
[Note] If the power on time is 999999 hours or more, it is always reported as 999999 hours. [Note] If the power on time is “*E** ****”, the value may not be correct due to the life of the flash memory. AVH-P3200BT/XNUC...
Page 83
2: DVD Dual Layer Completion 3: CD 5 Return select 4: CD-RW CRG moves 5: Return to the most outer <Error> ERROR 1: Power OFF select Code : 00000000 Please Input Number <Error : Power OFF> ERROR Code : 00000000 Please Reset AVH-P3200BT/XNUC...
LCD Assy. Removing the Monitor PCB (Fig.4) Disconnect the two FFC. Remove the five screws and then remove the Monitor. Fig.4 Monitor PCB Removing the Keyboard PCB (Fig.5) Keyboard PCB Remove the screw and then remove the Keyboard PCB. Fig.5 AVH-P3200BT/XNUC...
Page 85
Remove the three screws and then remove the Heat Sink and Holder. Fig.7 Removing the the Upper Chassis (Fig.8, 9, 10) Fig.8 Remove the screw.(Fig.8) Upper Chassis Fig.9 Remove the four screws and then remove the Upper Chassis.(Fig.9, 10) Fig.10 AVH-P3200BT/XNUC...
Page 86
Do not insert the Coaxial Jumper in extreme slant, as the connector might suffer damage. Removing the the BT ANT PCB (Fig.12) Disconnect the Cord Assy using GGF1539. Fig.12 Remove the screw and then remove the BT ANT PCB. BT ANT PCB AVH-P3200BT/XNUC...
Page 87
How to have it 1.Have a specified part. Handling OK Handling NG AVH-P3200BT/XNUC...
Page 88
(Precaution) If the PU goes to the outer most periphery, it idles. It is not a problem, but please try not to let it idle as much as possible. GND the brown line 4V to the gray line Fig. 1 Fig. 2 Connector (relay FFC) Relay FFC AVH-P3200BT/XNUC...
Page 89
Fig. 1 T-case washer Drive gear Fig. 2 c.Clamp state with no disc loaded a.Ejecting state b.Open-lock state There is a There is space no space AVH-P3200BT/XNUC...
Page 90
6.As in the Figures, while supporting the location A with your fingers, screw the relay PCB. (Fig. 7 / Fig. 8) 7.Solder the lead for the CRG motor. 8.Fit the relay FFC to the connector. Fig. 7 Fig. 8 AVH-P3200BT/XNUC...
Page 91
(Precaution) The relay FFC must be removed for certainty in order to prevent the IC damage. 2.Apply 1.5V to the CRG motor and then transfer the PU to the outer periphery. (Precaution) Do not forget to reinstall the relay FFC after sending the PU to the outer periphery and take the necessary measures. AVH-P3200BT/XNUC...
Laser didoes may be damaged, if the volume switch for the minus side of the probe, the body frame of the the laser power adjustment of the pick up unit, is turned. measurement device should be set to floating ground. AVH-P3200BT/XNUC...
Page 93
Oscilloscope Symptom in case the adjustment is not adequate: Worsening of the error rate 10 (Normally 10 or less.) Large RF jitter RF waveform distortion Tracking drawing/Unstable servo * Caution: Do not look into the laser light during adjustment. AVH-P3200BT/XNUC...
Page 94
Next, slightly turn the skew adjusting screw B so the level would reach its maximum. Slightly turn the skew adjusting screw A again so the level would reach its maximum. (Make adjustment in the order of A->B->A and in the end complete adjustment by turning each screw in the clockwise direction.) AVH-P3200BT/XNUC...
Page 95
5: CRG Move Outer 6: Eject Please Input Number 12. In order to produce the clamping state with no disc loaded, slightly move the disc detection arm in the counterclockwise direction while moving the switch arms outward. Switch arms AVH-P3200BT/XNUC...
Page 96
1: Power OFF CRG Move Outer 1: Power OFF Please Input Number 15. TEST MODE Select “6: Eject.” TEST MODE 1: LD ON 2: ASMAX 3: Skew Adjustment 4: Error Rate 5: CRG Move Outer 6: Eject Please Input Number AVH-P3200BT/XNUC...
Page 97
Locations to make SKEW adjustment Locations to adhere the SKEW 1,2,3: GEM1033 AVH-P3200BT/XNUC...
Page 98
Bond for resonance 4:Three Bond 1530 adhesive Bond for locking the screw 5,6 : Three Bond 1401M Bond for locking the screw AVH-P3200BT/XNUC...
Page 99
Precautions on handling the PU *Precaution: Do not touch those shaded areas in the following figures. Hologram (Beware of the static) Do not touch the optical part RF level adjusting part Do not touch the spring AVH-P3200BT/XNUC...
Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) 9.1 PACKING BT/RD DVD/RC DVD/RD DVD/RI BT/UC DVD/UC BT/UC BT/RD AVH-P3200BT/XNUC...
Page 105
14-5 Warranty Card See Contrast table (2) Protector CHP3952 Microphone Assy See Contrast table (2) (2) CONTRAST TABLE AVH-P3200BT/XNUC, AVH-P3250BT/XNRD, AVH-P3200DVD/XNUC, AVH-P3250DVD/XNRC, AVH-P3250DVD/ XNRD and AVH-P3250DVD/XNRI are constructed the same except for the following: Mark Description AVH-P3200BT/XNUC AVH-P3250BT/XNRD AVH-P3200DVD/XNUC Screw Assy...
Page 106
Part No. Language CRB3174 English CRB3175 French CRB3176 Spanish(Espanol) CRD4452 English, French, Spanish(Espanol) CRB3177 English CRB3178 Traditional Chinese CRB3179 Korean CRD4453 English, Traditional Chinese, Korean CRB3276 English CRB3180 Spanish(Espanol) CRB3181 Portuguese(B) CRD4454 English, Spanish(Espanol), Portuguese(B) CRB3182 Arabic CRD4455 English, Arabic AVH-P3200BT/XNUC...
Page 109
See Contrast table (2) Screw(M2 x 3) CBA1877 Service Unit(Keyboard PCB) CXX2764 Cover CNN2628 (2) CONTRAST TABLE AVH-P3200BT/XNUC, AVH-P3250BT/XNRD, AVH-P3200DVD/XNUC, AVH-P3250DVD/XNRC, AVH-P3250DVD/ XNRD and AVH-P3250DVD/XNRI are constructed the same except for the following: Mark Description AVH-P3200BT/XNUC AVH-P3250BT/XNRD AVH-P3200DVD/XNUC Grille Unit CXE2609...
Page 111
See Contrast table (2) Screw BPZ26P080FTC Holder CND5502 Screw BSZ26P060FTC CDE8747 (2) CONTRAST TABLE AVH-P3200BT/XNUC, AVH-P3250BT/XNRD, AVH-P3200DVD/XNUC, AVH-P3250DVD/XNRC, AVH-P3250DVD/ XNRD and AVH-P3250DVD/XNRI are constructed the same except for the following: Mark Description AVH-P3200BT/XNUC AVH-P3250BT/XNRD AVH-P3200DVD/XNUC Service Unit(Mother Assy) CXX2760 CXX2759...
10.6 MOTHER UNIT(TUNER) model P : AVH-P3200BT/XNUC Q : AVH-P3250BT/XNRD J : AVH-P3200DVD/XNUC K : AVH-P3250DVD/XNRC L : AVH-P3250DVD/XNRD MOTHER UNIT (TUNER) M : AVH-P3250DVD/XNRI CHIP SIZE LEGEND 1608 2125 3216 ANA-TUN BUS TUN_R TUN_L SYS-TUN BUS GNDBE2 Q403 HSLK...
COIL U CSN1068-A COIL V CN1201 DSCSNS HALL W+ DSCSNS1 DSCSNS1_B DSCSNS0 DSCSNS0_B CSN1068-A HALL W- R103 HALL V+ S102 HALL V- HALL U+ HALL U- HALL BIAS- CRGP CRG+ CRGM LOAD/CRG MOTOR CRG- CXC4026 SPINDLE MOTOR EXM1050 CKS6063 CN101 AVH-P3200BT/XNUC...
PC board. IC 301 (A, 91, 111) IC NJM2068V Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. Unit Number : (P) P:AVH-P3200BT/XNUC Unit Number : (Q) Q:AVH-P3250BT/XNRD Unit Number : (J) J:AVH-P3200DVD/XNUC Unit Number : (K) K:AVH-P3250DVD/XNRC...
Page 183
(A,98,95) Diode DAN202U (A,104,111) Poly Switch MINISMDC075F/24 D 301 (B,92,75) Diode RKZ2.4KG(B) >P564 (A,157,104) Poly Switch MINISMDC075F/24 D 361 (A,78,101) Diode RKZ3.9KG(B2) >P1501 (B,26,77) Fuse 6.3 A CEK1262 D 542 (B,52,15) Diode DZ2S068C >P1611 (A,72,60) Fuse 2.5 A CEK1285 AVH-P3200BT/XNUC...
Page 184
R 209 (A,105,104) RS1/16SS272J R 366 (A,86,102) RS1/16SS104J R 223 (B,102,84) RS1/16SS473J R 367 (A,78,104) RS1/16SS473J R 227 (B,122,85) RS1/16SS272J R 368 (A,86,104) RS1/16SS473J R 228 (B,122,82) RS1/16SS272J R 369 (A,88,98) RS1/16SS103J R 229 (B,122,83) RS1/16SS562J R 370 (A,87,102) RS1/16SS472J AVH-P3200BT/XNUC...
Page 185
R 711 (B,124,56) RS1/16SS473J R 579 (A,136,109) RS1/16SS472J R 712 (B,121,51) RS1/16SS103J R 580 (A,133,109) RS1/16SS472J R 713 (B,117,51) RS1/16SS104J R 582 (A,37,105) (Q,K,L,M) RS1/16SS473J R 716 (B,138,57) (P,Q) RS1/16SS473J R 583 (A,33,105) (Q,K,L,M) RS1/16SS121J R 724 (A,146,52) RS1/16SS471J AVH-P3200BT/XNUC...
Page 186
R 843 (A,83,27) RS1/16SS221J R 991 (B,106,36) RS1/16SS103J R 844 (A,83,35) RS1/16SS221J R 992 (B,113,36) RS1/16SS103J R 845 (A,82,35) RS1/16SS104J R 993 (B,108,36) RS1/16SS103J R 846 (A,89,29) RS1/16SS102J R 1001 (B,12,66) RS1/16SS391J R 1002 (A,11,64) RS1/10SR2R2J R 848 (A,86,34) RS1/16SS472J AVH-P3200BT/XNUC...
Page 187
C 289 (A,150,97) CKSSYB104K10 C 163 (A,72,111) CKSRYB104K50 C 290 (A,136,95) CEVW220M16 C 164 (B,79,106) 10 uF CCG1236 C 291 (A,132,98) CKSSYB104K10 C 165 (B,90,107) CKSQYB225K10 C 293 (B,138,84) CKSRYB104K16 C 166 (B,75,101) 10 uF DCH1201 C 294 (B,140,84) CKSRYB104K16 AVH-P3200BT/XNUC...
Page 188
C 945 (B,98,62) CKSQYB475K6R3 C 795 (A,38,31) (P,Q) CEVW471M10 C 946 (A,70,60) 10 uF DCH1201 C 801 (A,49,37) CKSSYB104K10 C 951 (A,89,26) CKSSYB104K10 C 802 (A,49,48) CKSSYB104K10 C 952 (A,86,26) CKSSYB104K10 C 803 (A,49,45) CKSSYB104K10 C 981 (B,108,47) CKSSYB473K10 AVH-P3200BT/XNUC...
Page 189
C 1732 (A,140,22) CEVW101M16 D 3501 (B,6,50) Diode DZ2S068C C 1733 (A,145,19) CKSSYB104K10 C 1746 (B,150,33) CKSSYB104K10 D 3502 (B,6,41) Diode DZ2S068C C 1747 (B,150,25) CKSSYB104K10 D 3504 (B,12,55) Diode DZ2S068C C 1771 (B,28,37) CKSQYB225K10 D 3506 (B,17,29) Diode EMZC6.8N AVH-P3200BT/XNUC...
Page 190
R 5309 (A,96,32) RS1/16SS0R0J CN3502 (A,11,29) Connector YKS5032 R 5310 (A,103,45) RS1/16SS222J CN3811 (A,13,21) Connector(P,Q) CKS5749 R 5311 (A,103,43) RS1/16SS271J CN5002 (A,119,29) Connector DKN1385 R 5312 (A,101,42) RS1/16SS684J CN5101 (A,122,15) Connector CKS5561 R 5313 (A,94,42) RS1/16SS1502D CN5601 (A,102,75) Connector CKS6062 AVH-P3200BT/XNUC...
Page 191
(A,20,31) RS1/16SS0R0J R 7507 (B,27,35) RS1/16SS151J R 5706 (A,19,31) RS1/16SS0R0J R 7508 (B,24,35) RS1/16SS151J R 5707 (A,32,39) RS1/16SS3301F R 7517 (B,29,44) RAB4CQ223J R 5708 (A,9,33) RS1/16SS102J R 7518 (B,33,44) RAB4CQ223J R 5709 (A,24,27) RS1/10SR1103D R 7521 (B,9,34) (P,Q) RS1/16SS0R0J AVH-P3200BT/XNUC...
Page 192
CCG1236 C 5502 (A,40,67) CKSRYB105K10 C 5703 (A,7,50) 10 uF CCG1236 C 5503 (A,81,47) CKSSYB104K10 C 5704 (A,10,54) CKSRYB104K16 C 5504 (A,84,35) 10 uF DCH1201 C 5705 (A,25,31) 10 uF CCG1236 C 5505 (A,73,44) CSZS100M10 C 5706 (A,14,34) CKSSYB104K16 AVH-P3200BT/XNUC...
Page 193
R 1501 (B,46,7) RS1/16SS122J X 1501 (B,43,7) Oscillator 27.000 MHz CSS1768 R 1503 (B,45,8) RS1/16SS105J EF1001 (B,5,12) Chip EMI Filter DTF1106 R 1504 (B,45,13) RS1/16SS120J EF1002 (B,11,13) Chip EMI Filter DTL1106 R 1505 (A,43,13) RS1/16SS101J CN1101 (A,66,49) Connector CKS5775 AVH-P3200BT/XNUC...
Page 194
C 1517 (A,74,16) CKSSYB104K10 C 1010 (B,26,18) CKSQYB225K10 C 1518 (A,75,22) CKSSYB104K10 C 1011 (B,22,18) CKSRYB105K10 C 1519 (A,74,26) CKSSYB104K10 C 1013 (B,15,25) 10 uF DCH1201 C 1520 (A,75,30) CKSSYB104K10 C 1014 (B,13,25) 10 uF DCH1201 C 1521 (A,60,37) CKSSYB104K10 AVH-P3200BT/XNUC...
Page 195
Unit Name : Connect PCB MISCELLANEOUS S 101 (B,51,37) Switch(HOME) CSN1068 S 102 (B,12,23) Switch(DSCSNS) CSN1068 S 103 (B,22,10) Switch(8SNS) CSN1068 R 101 (B,52,27) RS1/16S101J R 102 (B,15,29) RS1/16S101J R 103 (B,16,11) RS1/16S101J C 101 (B,51,23) CKSRYB104K50 Miscellaneous Parts List AVH-P3200BT/XNUC...