Advertisement
Quick Links
4-696-254-11(1)
Network Camera
Installation Manual
Before operating the unit, please read this manual thoroughly and
retain it for future reference.
SNC-VB642D/EB642R
© 2017 Sony Corporation
A
B
9
C
D
Vertical marker
Hole for connecting
cables ø40 (1
5
/
)
8
Hole for installing
the stand
Horizontal maker
83.7 (3
/
)
3
10
85.7 (3
3
/
)
8
Unit: mm (inches)
E
Ceiling
Wire rope
(supplied)
Camera unit mounting screw
(commercially-available) (4)
6
7
F
8
1
Liner
9
10
11
12
Twice
2
2-a LAN cable
Tab
10 (
1
/
)
10 (
2
Overlap at least
half of its width
2-b SP terminal / MIC terminal / I/O (Input/Output) cable / BNC
cable
SNC-VB642D
10 (
1
/
)
10 (
1
/
)
2
2
Overlap at least
Overlap at least
half of its width
half of its width
2-c Power input cable
SNC-VB642D
SNC-EB642R
Heat shrinkable tube
Heat shrinkable tube
Overlap at least
Overlap at least
half of its width
half of its width
30 (1
/
)
1
4
Wrap this part
two-fold
About the Manuals
Safety Regulations (included)
The Safety Regulations describes notes for the secure usage of camera. Be sure
to read it.
Installation Manual (this document)
Describes the names and functions of parts and controls of the Network Camera,
gives connection examples and explains how to set up the camera. Be sure to
read the Installation Manual before operating.
The illustration of SNC-VB642D is used for example purpose.
Electronic Instruction Manual (Web)
ˎ
How to control the camera via a web browser
ˎ
How to setup the camera
Operate the camera referring to the guide above after having installed and
connected the camera properly based on the Installation Manual.
Assigning the IP address
1
Download the installer for "SNC toolbox" to a folder from the download
site.
2
Install the SNC toolbox.
Unzip the ZIP file of the downloaded installer.
Double-click "SncToolbox_Setup.exe. " For details on installing and use refer to
the Application Guide.
3
Assign an IP address.
Assign an IP address using the installed SNC toolbox. For details, see "Using
SNC toolbox" – "Assign an IP address" in the Application Guide.
Tip
SNC toolbox stands for Sony Network Camera toolbox.
Location and Function of Part
Front
Audio cable
The connector with the longer cable (SP) is used for the line output connector,
and the shorter cable (MIC) is used for the microphone/line input connector.
ˎ
SP terminal (minijack, monaural)
Connect a commercially available speaker system with a built-in amplifier.
ˎ
MIC terminal (minijack, monaural)
Connect a commercially available microphone. This jack supports plugin-
power microphones (rated voltage: 2.5 V DC).
I/O (Input/Output) cable
Use for SNC-VB642D only.
This cable is provided with two sensor inputs and two alarm outputs. The wires
of the cable control the following signals.
Color of wire
Red
White
Black
Yellow
Brown
Green
Blue
For details on each function and required settings, see the User's Guide.
For wiring, see "Connecting the I/O Cable" (P2).
Wire rope
When installing the camera on the ceiling or the wall, make sure to attach the
supplied wire rope.
Sun shield nut
Front cover
Power input cable
Use for SNC-VB642D only.
Connect this cable to a 24 V AC or 12 V DC power supply system.
You can screw an extension cable in the connector tip attached at the end of the
cable. Connect GND to the FG terminal (center of 3-pin connector). See
illustration .
BNC cable
Outputs a composite video signal.
Ground wire
Ground the camera when you install it.
LAN cable (RJ-45)
Connect this cable to a hub or computer on the 10BASE-T or 100BASE-TX
network using a commercially available network cable (category 5).
Note
Take care not to trap the cables between the camera and the ceiling or the wall. If
the cable is trapped, it may cause a fire or electric shock due to breaking.
Sun shield
The sun shield can be adjusted horizontally up to 26 mm (1
required.
Camera
Front cover screw (four positions)
Inside
Lens
POWER indicator (Green)
When the power is supplied to the camera, the camera starts checking the
system. If the system is normal, this indicator lights up.
HEATER indicator (Green)
The indicator lights up in green when the built-in heater is working normally.
NETWORK indicator (Green/Orange)
The indicator lights up or flashes when the camera is connected to the network.
The indicator is off when the camera is not connected to the network.
1
/
)
2
Mode setting DIP switches
DIP switch function/settings
SNC-VB642D
Switch No.
Up (ON)
Down (OFF)
1 VIDEO (NTSC/PAL) switch (Initial setting: NTSC)
Switches the video output.
After setting the switch, reboot the camera unit.
2 POWER (PoE+, AC, DC/PoE) switch (Initial setting: PoE+, AC, DC)
SNC-EB642R
Change according to the power you are using.
10 (
1
/
)
2
Note
When power is supplied by IEEE802.3af (PoE) equipment, if the switch is set to
PoE+, the camera will not work properly.
When the power is supplied via power supply equipment that complies with
IEEE802.3at (PoE+), an AC power adaptor, or a DC power adaptor, the heater
will not work if the switch is set to PoE. Note that if you use the camera in a low
temperature, the camera may not work.
SNC-EB642R
Switch No.
Up (ON)
Down (OFF)
1 VIDEO (NTSC/PAL) switch (Initial setting: NTSC)
Switches the video output.
After setting the switch, reboot the camera unit.
2 HEATER (AUTO/OFF) switch (Initial setting: AUTO)
The integrated heater function will be deactivated when it is set to OFF. Be
sure to set to AUTO when you use the camera in cool environment.
Reset switch
To reset the camera to the factory default settings, hold down this switch with a
point and supply the power to the camera.
MONITOR output jack
Connect this jack to a video input connector of a video monitor. You can adjust
the camera or lens while looking at the image on the video monitor. After
adjusting the camera or lens, disconnect the cable.
ZOOM/FOCUS switch
Wrap this part
two-fold
Use this switch to adjust lens' zoom and focus. Slide the switch lever to select the
desired function.
Unit: mm (inches)
[W] WIDE: Zoom out
[T] TELE: Zoom in
[N] NEAR: Focus on a nearby subject
[F] FAR: Focus on a distant subject
Hold down the center of the ZOOM/FOCUS switch for a moment to focus
automatically.
SD card slot
This slot is used for optional SD memory cards.
Image data in the camera can be recorded to a memory card by inserting it into
the slot.
Gently insert an SD card in (see illustration) until it clicks into place.
This unit is only compatible with SD and SDHC memory cards.
Note
For inquiries regarding verified SD memory cards, contact your authorized Sony
dealer.
Back
Base stand
Base screw (two positions)
TOP mark
Arm screw
Arm
Rating label
Shows the name of this camera and its electric rating.
Water drain
When installing the unit on a wall, make sure this water drain is not sealed.
Installation
WARNING
ˎ
If you attach the camera in the height such as the wall or the ceiling, etc.,
entrust the installation to an experienced contractor or installer.
ˎ
If you install the camera at a height, ensure that the installation location and
its material are strong enough to withstand a weight of 15 kg (33 lb 11 oz) or
more, and then install the camera securely. If the ceiling is not strong enough,
the camera may fall and cause serious injury.
ˎ
Do not pull on any cables forcefully, as a connection may become loose.
ˎ
To prevent the camera from falling, make sure to attach the supplied wire rope.
ˎ
If you attach the camera to the ceiling, check periodically, at least once a year,
to ensure that the connection has not loosened. If conditions warrant, make
this periodic check more frequently.
Deciding the Installation Location of the Camera
After deciding the direction in which the camera will shoot, make the required hole
Name
(ø40 mm (1
/
23
40
Sensor In 1+
Then decide the four mounting hole positions to install the base stand.
Sensor In 2+
Mounting screws
Sensor In – (GND)
The camera stand is provided with four ø4.5 mm (
Alarm Out 1+
Install the camera stand on a ceiling or wall with screws through four mounting
Alarm Out 1–
holes: The required mounting screws differ depending on the installation
Alarm Out 2+
location and its material. Use commercially-available screws.
Alarm Out 2–
Steel wall or ceiling: Use M4 bolts and nuts.
Wooden wall or ceiling: Use M4 tapping screws. The panel thickness must be
15 mm (
/
inches) or more.
5
8
Concrete wall: Use anchors, bolts and plugs suitable for concrete walls.
Junction box: Use screws to match the holes on the junction box.
WARNING
The required mounting screws differ depending on the installation location and
its material. If you do not secure the camera with the appropriate mounting
screws, the camera may fall off.
Installing the Camera
1
Pass the cables through the hole for connecting cables made at the
installing surface.
2
Fix the wire rope to the wall or ceiling.
3
Install the camera on the wall or ceiling.
The remaining cable can be incorporated in the space between the base
stand and the mounting surface. (-)
Insert the four screws in the screw holes on the camera stand, and then
tighten the screws to attach the camera.
When installing the camera on the wall, be sure the TOP mark on the camera
stand is at the top.
Refer to "Mounting screws" in section D for screw to be used.
Notes
ˎ
If you install the camera unit on a ceiling, take adequate waterproofing
measures to prevent water seepage into the stand.
ˎ
When installing the unit on a wall, make sure the water drain is not sealed.
1
/
inches), as
8
Notes on waterproofing of cable connection area
Despite the fact that this unit is rated IP66, the cables and/or the connectors
join to the outside are not waterproof. To prevent water ingress from the cables
and/or the connectors, waterproof them with the supplied waterproof tape as
follows. Otherwise, there may be a risk of water entering through the cables
and/or the connectors and shorting the unit or the connectors.
1
Connect all the required cables and the ground wire.
2
To obtain optimal waterproofing, tear off the liner before wrapping,
then stretch the tape to twice its original length. (-1)
If it is not fully stretched, the waterproofing function of the tape can not be
achieved.
3
Overlap the tape at least half of its width when wrapping. (-2)
Notes
ˎ
Do not press the network cable tab down when wrapping it.
ˎ
When you wrap the power input cable, start from the heat shrinkable tube.
Make sure at least 30 mm (1
the power supply equipment is wrapped. (2-c)
ˎ
Since the connector of the power input cable has gaps, wrap the connector
part two-fold.
ˎ
Make sure at least 10 mm (
1
2
input cable) is wrapped.
VIDEO
POWER
ˎ
Make sure there is no unwrapped part or damage on the tape.
PAL
PoE+, AC, DC
4
After wrapping, squeeze the tape with your fingers at the overlapping
NTSC
PoE
parts so that layers are airtight and fully adhered.
1
2
VIDEO
HEATER
PAL
AUTO
NTSC
OFF
inches)) for the connecting cables using the supplied template.
/
inches) mounting holes.
3
16
/
inches) of the wire part that is connected to
1
4
1
/
inches) of the wire part (excluding the power
2
Advertisement
Related Manuals for Sony SNC-VB642D
Summary of Contents for Sony SNC-VB642D
-
Page 1: Network Camera
Describes the names and functions of parts and controls of the Network Camera, Note gives connection examples and explains how to set up the camera. Be sure to For inquiries regarding verified SD memory cards, contact your authorized Sony Unit: mm (inches) read the Installation Manual before operating. - Page 2 Start temperature: –20°C to +50°C (–4°F to +122°F) Connecting to 12 V DC or 24 V AC source (SNC-VB642D) Working temperature: –30°C to +50°C (–22°F to +122°F) Connect the power input cable of the camera to a 12 V DC or 24 V AC source.