Xerox Nuvera 100 Hints And Tips Manual
Production system
Hide thumbs
Also See for Nuvera 100:
- Software manual (498 pages) ,
- Service manual (304 pages) ,
- Installation planning manual (242 pages)
Related Manuals for Xerox Nuvera 100
Summary of Contents for Xerox Nuvera 100
- Page 1 Software Version 10.2 21 May 2010 701P50711 ® Xerox Nuvera Hints and Tips Guide Xerox Nuvera 100/120/144 EA/MX Production System Xerox Nuvera 200/288 EA/MX Perfecting Production System...
- Page 2 ©2010 Xerox Corporation. All rights reserved. XEROX® and XEROX and Design®, Xerox Nuvera® and FreeFlow® are trademarks of Xerox Corporation in the United States and/or other countries. Changes are periodically made to this document. Technical inaccuracies and typographic errors will be corrected in subsequent editions.
-
Page 3: Table Of Contents
Issues resolved ...........................3-1 Issues remaining from previous release ................3-2 CQ#45919 Tray Programming Reverts to Default Settings ......3-2 CQ#45544 Build Job ......................3-2 CQ#43471 Skewed Inserts with Xerox Tape Binder ..........3-2 CQ#43522 Annotation-1 ....................3-2 CQ#43522 Annotation-2 ....................3-3 CQ#44256 Configuration Backup ................3-3 CQ#44223 PDF and HTML Files Viewed from CD ..........3-3... -
Page 5: Preface
System Administrator’s Guide as well as the DFA Resource Guide. • For print driver installation, supported print drivers, and common issues with the Xerox FreeFlow® Print Server print driver functionality, refer to the CentreWare Printer Drivers Guide. New print drivers are available at www.xerox.com. - Page 6 Preface Xerox Nuvera [This page left intentionally blank] Hints and Tips Guide...
-
Page 7: Software Versions
System Restore * Note Since the Xerox software supports the current release and two past major releases, DocuSP Remote Workflow 5.1 software supports DocuSP versions 4.1, 4.2, 5.0, and 5.1. If an earlier version of DocuSP is being used, you can install an older version of DocuSP Remote Workflow. -
Page 9: New Capabilities In Version 10.2 Software
Software The following is a list of new capabilities enabled with version 10.2 software: 1. The Xerox Tape Binder (XTB) is now configurable in Dual Mode (2 XTB’s connected together). 2. Disable status messages when trays are disabled. This de-clutters the status message area when a tray is disabled. -
Page 11: Release Issues
Release Issues Issues resolved The following is a list of Nuvera 10.1 issues that have been resolved and no longer apply to Xerox Nuvera 10.2 systems: • CQ#43933 Unable to Eject CD Tray • CQ#45892 MICR Mode does not disable Edge Treatment... -
Page 12: Issues Remaining From Previous Release
Once you are in Build Job you can change the paper selection to any stock you wish. You also can leave it set to APS. CQ#43471 Skewed Inserts with Xerox Tape Binder Description Books printed on 60gsm paper that have heavy (90gsm and higher) inserts can cause last several pages in the book to be skewed. -
Page 13: Cq#43522 Annotation-2
Xerox Nuvera Release Issues CQ#43522 Annotation-2 Description When performing a “Copy and Save” or “Print and Save” operation with annotations turned on, the reprint of the saved job will be unreadable. Workaround Perform a “Save” operation and then “Print” the saved job. -
Page 14: Cq#38117 Short Edge Feed 9X11 Stock
Release Issues Xerox Nuvera CQ#38117 Short Edge Feed 9x11 Stock Description 9 x 11 stock cannot be loaded short edge first (SEF). Workaround Load an SEF-only stock such as Legal, run one or more sheets on that stock, then unload it and... -
Page 15: Cq#46849 Message Stating 'The Online Configuration File Online.config Does Not Exist' When Closing The 'Gateways
Xerox Nuvera Release Issues CQ#46849 Message stating 'The online configuration file online.config does not exist' when closing the 'Gateways' Description The above error message may occur when closing the “Gateways” window in the Online Setup tab. Workaround If this occurs, select OK in the error message and then close or Cancel in the gateways window. -
Page 16: When Exiting Micr Mode, The Edge Erase Remains At No Erase
Release Issues Xerox Nuvera When exiting MICR Mode, the Edge erase remains at no erase Description When exiting MICR Mode, the edge erase setting will remain at “none”. We leave it to the user to set the edge erase to the values they want.