72.7kg 70kg 160lbs 154lbs The ( tured by Sony Corporation under license from SRS Labs, Inc. It is covered by U.S. Patent No. 4,748,669. Other U.S. and foreign patents pending. 34VL65C/35V65/37VL65/37VL65C) The word ‘SRS’ and the SRS symbol ( trademarks of SRS Labs, Inc.
LES SCHEMAS DE PRINCIPE, LES VUES EXPLOSEES ET LES LISTES DE PIECES SONT D'UNEIMPORTANCE CRITIQUE POUR LA SECURITE DU FONCTIONNEMENT. NE LES REMPLACER QUE PAR DES COMPOSANTS SONY DONT LE NUMERO DE PIECE EST INDIQUE DANS LE PRESENT MANUEL OU DANS DES SUPPLEMENTS CIRCUIT PUBLIES PAR SONY.
Page 4
KV-32S40/32S45/34SL40/34SL40C/34SL40T/34SL45/35S40/35S45/37SL45/ 32V40/32V65/34VL65/34VL65C/35V65/37VL65/37VL65C After correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly- soldered connections. Check the entire board surface for solder splashes and bridges. 2.
(through your cable box), and normal (CATV) channels by pressing ANT on your remote control. Notes • Your Sony remote control can be programmed to operate your cable box. (see page 32) • When using PIP, you cannot view the AUX input in the window picture.
Page 6
Disconnect all power sources before making any connections. VCR Connections VCR must be connected and Connecting an antenna/cable TV turned on to operate PIP (KV-32S45, 35S45 only). system with a VCR Attach the coaxial connector from your cable or antenna to IN on your VCR. Using A/V connectors, connect AUDIO and Cable VIDEO OUT on your VCR to AUDIO and...
• When you remove the batteries, the code number may Zenith revert to the factory setting. Operating a VCR Buttons on the • The code numbers for Sony VCR's are assigned at the 309, 335 remote control factory as follows: 305, 304 To turn on or off Press VTR/DVD (POWER).
(see page 26) If, after reading these operating instructions, you have additional questions related to the use of your Sony television, please call our Direct Response Center at 1-800-222-SONY (7669). (U.S. residents only) Troubleshooting Cable box code numbers Consult the table below;...
KV-32S40/32S45/34SL40/34SL40C/34SL40T/34SL45/35S40/35S45/37SL45/ 32V40/32V65/34VL65/34VL65C/35V65/37VL65/37VL65C 2-3. SERVICE POSITION 1 1 A Board ANODE-CAP REMOVAL WARNING: High voltage remains in the CRT even after the power is disconnected. To avoid electrical shock, discharge CRT before attempting to remove the anode cap. Short between anode and coated earth ground strap of CRT. NOTE: After removing the anode, short circuit the anode of the picture tube and the anode cap to either the metal chassis, CRT shield or carbon painted on the CRT.
2-5-1. PICTURE TUBE REMOVAL WARNING -- Before removing anode cap: High voltage remains in the CRT even after the power is disconnected. To avoid electrical shock, discharge CRT before attempting to remove the anode cap. Short between anode and coated earth ground strap of CRT.
KV-32S40/32S45/34SL40/34SL40C/34SL40T/34SL45/35S40/35S45/37SL45/ 32V40/32V65/34VL65/34VL65C/35V65/37VL65/37VL65C The following adjustments should be made when a complete realignment is required or a new picture tube is installed. These adjustments should be performed with rated power supply voltage unless otherwise noted. The controls and switch should be set as follows unless otherwise noted: PICTURE control ...
Page 13
3-2. CONVERGENCE Preparation: • Before starting, perform FOCUS, V. LIN and V. SIZE adjustments. • Set BRIGHTNESS control to minimum. • Input dot pattern. (1) Vertical and Horizontal Static Convergence Adjust V. STAT magnet to converge red, green and blue dots in the center of the screen.
KV-32S40/32S45/34SL40/34SL40C/34SL40T/34SL45/35S40/35S45/37SL45/ 32V40/32V65/34VL65/34VL65C/35V65/37VL65/37VL65C ( 2 ) Dynamic Convergence Adjustment • Before starting, perform Horizontal and Vertical Static Convergence Adjustment. 1. Slightly loosen deflection yoke screw. Remove deflection yoke spacers. Move the deflection yoke for best convergence as shown below: B G R B R G B R G B B G R R G B R...
R530, R531 CONFIRMATION METHOD (HOLD-DOWN CONFIRMATION) AND READJUSTMENTS Always perform the following adjustments when replacing the following components marked with a ] mark on the schematic diagram: A BOARD: IC351, IC501, D519, D520, D521, C531, C532, R387, R529, R530, R531, R532, R533, R550, T503 G BOARD: IC643, R661...
Page 16
KV-32S40/32S45/34SL40/34SL40C/34SL40T/34SL45/35S40/35S45/37SL45/ 32V40/32V65/34VL65/34VL65C/35V65/37VL65/37VL65C ELECTRICAL ADJUSTMENT BY REMOTE COMMANDER Use Remote Commander (RM-Y167) to perform the following circuit adjustments: NOTE : Test Equipment Required: 1. Pattern Generator 2. Frequency Counter 3. Digital Multimeter 4. Audio OSC (1) Method of Setting the Service Adjustment Mode SERVICE MODE PROCEDURE 1.
Page 17
(4) Service Data Register Description Name VP CXA2095S VPOS V-Position VSIZ V-Size VCOM V-Compensation VLIN V-Linearity VSCO S-Correction HPOS H-Position HSIZ H-Size PAMP Pin Compensation UPIN Upper Corner Pin LPIN Lower Corner Pin PPHA Pin Phase VBOW AFC Bow VANG AFC Angle Reference Line GDRV...
Page 18
KV-32S40/32S45/34SL40/34SL40C/34SL40T/34SL45/35S40/35S45/37SL45/ 32V40/32V65/34VL65/34VL65C/35V65/37VL65/37VL65C Service Data (cont.) Register Description Name PI SDA9288 PYSD Select Delay PIPH PIP H-position PIPV PIP V-position PYDL PIP Y-delay PHDL H-pulse delay PMVD Main V-pulse delay PIVD Inset V-pulse delay PCON Inset Contrast FRMY Frame Y CHRI Input Polarity CHRO Output Polarity...
Page 19
Service Data (cont.) Register Description Name ID MAP ID-0 ID-0 (Language/Color Systems) ID-1 ID-1 (Input/Output Conifguration) ID-2 ID-2 (Audio) ID-3 ID-3 (OSD/Timer/V-chip/Ch Fix) ID-4 ID-4 (CC/Spot Killer/etc) ID-5 ID-5 (V-series Features/etc) ID-6 ID-6 (PiP/Ant Sw related) ID-7 ID-7 (Special Models/etc) **AVERAGE DATA MODEL GROUPINGS: 32"/34"...
Page 20
KV-32S40/32S45/34SL40/34SL40C/34SL40T/34SL45/35S40/35S45/37SL45/ 32V40/32V65/34VL65/34VL65C/35V65/37VL65/37VL65C SUB BRIGHT ADJUSTMENT (SBRT) 1. Set to Service adjustment Mode. 2. Input a gray scale pattern signal. 3. Set the PICTURE to minimum, and BRIGHT to normal. 4. Select SBRT with 5. Adjust SUB BRIGHT level with second from the right is faintly visible. 6.
V. SIZE ADJUSTMENT ( VSIZ) 1. Input a cross-hatch signal. 2. Set to Service adjustment mode. 3. Select VSIZ with 4.Adjust with for the best vertical size. 5.Write into the memory by pressing V. SIZE V. POSITION ADJUSTMENT (VPOS) 1.Input a cross-hatch signal. 2.Set to Service adjustment Mode.
6-3. CIRCUIT BOARDS LOCATION S MODELS (KV-32S45/32SL45/ 35S40/35S45/37SL45) (KV-35S40/ 35S45/37SL45) (KV-32S45/32SL45/35S45/37SL45) 6-4. PRINTED WRING BOARDS AND SCHEMATIC DIAGRAMS • All capacitors are in F unless otherwise noted. pF : indicated except for electrolytics and tantalums. • All electrolytics are in 50V unless otherwise specified. •...
KV-32S40/32S45/34SL40/34SL40C/34SL40T/34SL45/35S40/35S45/37SL45/ 32V40/32V65/34VL65/34VL65C/35V65/37VL65/37VL65C The components identified by shading and "¡ ¡ ¡ ¡ ¡ " mark are critical for safety. Replace only with specified part number. 7-3. CHASSIS (KV-32V40/32V65/34VL65/35VL65C/35V65/37VL65/37VL65C) 7-685-648-79 SCREW +BVTP 3X12 7-685-663-79 SCREW +BVTP 3X12 4-388-477-01 SCREW +BVTP 4X16 REF.NO.
Ne les remplacer que par une piece portant le numero specifie. DESCRIPTION REMARK BEZNET ASSY (KV-32V40 ONLY) BEZNET ASSY (KV-34VL65C/32V65/34VL65) 51,52 EMBLEM, (NO.9) SONY (KV-32V40 ONLY) DOOR, CONTROL (KV-32V40 ONLY) DOOR, CONTROL (EXCEPT KV-32V40) SWITCH, BLOCK CONTROL (KV-34VL65C/32V65/34VL65) BUTTON, MULTI (KV-32V40 ONLY) GUIDE, LED...
Ne les remplacer que par une piece portant le numero specifie. 108 109 DESCRIPTION REMARK BEZNET ASSY 101,102 EMBLEM, (NO. 9), SONY DOOR, CONTROL SWITCH, BLOCK CONTROL ITC 37GXT-A1 105,106 CRT 37GXT DY Y37GXA-X SCREW, TAPPING...
PARTS LISTING TABLE OF CONTENTS REF.NO. PART NO. DESCRIPTION A BOARD COMMON PARTS LIST (S SERIES): Parts common to all models listed in this manual...72 A BOARD VARIANT PARTS LIST (S SERIES): Parts that belong only to the model specified...80 A BOARD COMMON PARTS LIST (V SERIES): Parts common to all models listed in this manual...85 A BOARD VARIANT PARTS LIST (V SERIES): Parts that belong only to the model specified...91 Refer to the designated variant parts list when seeking a part indicated by an asterisk (*) on the A board schematic...
Page 40
S SERIES COMMON PARTS LISTING ELECTRICAL PARTS LIST (FOR S SERIES) Note: REF.NO. PART NO. The components identified by shading DESCRIPTION and mark ¡ ¡ ¡ ¡ ¡ a re critical for safety. Replace only with part number specified. Note: Les composants identifies per un trame et une marque ¡...
Page 41
Note: Note: The components identified Les composants identifies per un trame et une marque ¡ ¡ ¡ ¡ ¡ sont with shading and a critical symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for critiques pout la securite. Ne les safety.
Page 42
S SERIES COMMON PARTS LISTING REF.NO. PART NO. DESCRIPTION C1405 1-163-017-00 CERAMIC CHIP 0.0047MF C1406 1-126-956-91 ELECT 0.1MF C1407 1-163-017-00 CERAMIC CHIP 0.0047MF C1408 1-126-963-11 ELECT 4.7MF C1409 1-126-963-11 ELECT 4.7MF C1410 1-126-956-91 ELECT 0.1MF C1411 1-165-319-11 CERAMIC CHIP 0.1MF C1413 1-126-963-11 ELECT 4.7MF...
Page 43
Note: Note: The components identified Les composants identifies per un trame et une marque ¡ ¡ ¡ ¡ ¡ sont with shading and a critical symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for critiques pout la securite. Ne les safety.
Page 44
S SERIES COMMON PARTS LISTING REF.NO. PART NO. DESCRIPTION R044 1-216-033-00 RES, CHIP R046 1-247-815-91 CARBON R047 1-249-417-11 CARBON R048 1-249-417-11 CARBON R049 1-249-417-11 CARBON R052 1-216-061-00 RES, CHIP 3.3K R053 1-216-061-00 RES, CHIP 3.3K R054 1-216-061-00 RES, CHIP 3.3K R055 1-216-097-91 RES, CHIP 100K...
Page 45
Note: Note: The components identified by The components identified manual have been carefully factory-selected with shading and a critical for each set in order to satisfy regulations re- symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for garding X-ray radiation. Should replacement safety.
Page 46
S SERIES COMMON PARTS LISTING REF.NO. PART NO. DESCRIPTION R1122 1-216-115-00 RES, CHIP 560K R1123 1-216-039-00 RES, CHIP R1125 1-216-057-00 RES, CHIP 2.2K R1126 1-216-035-00 RES, CHIP R1127 1-216-115-00 RES, CHIP 560K R1128 1-216-039-00 RES, CHIP R1130 1-216-057-00 RES, CHIP 2.2K R1234 1-249-441-11 CARBON...
Page 47
REF.NO. PART NO. DESCRIPTION TRANSFORMER T501 1-437-210-11 TRANSFORMER, HORIZONTAL DRIVE T502 VARIANT (SEE VARIANT PARTS LIST) T503 VARIANT (SEE VARIANT PARTS LIST) T504 VARIANT (SEE VARIANT PARTS LIST) TUNER TU102 VARIANT (SEE VARIANT PARTS LIST) CRYSTAL X001 1-578-774-11 VIBRATOR, CRYSTAL X353 1-567-505-11 OSCILLATOR, CRYSTAL X354...
Page 48
ELECTRICAL PARTS LIST (FOR V SERIES) Note: REF.NO. PART NO. The components identified by shading DESCRIPTION and mark ¡ ¡ ¡ ¡ ¡ a re critical for safety. Replace only with part number specified. Note: Les composants identifies per un trame et une marque ¡...
Page 49
V SERIES COMMON PARTS LISTING REF.NO. PART NO. DESCRIPTION C463 VARIANT(SEE VARIANT PARTS LIST) C464 VARIANT(SEE VARIANT PARTS LIST) C466 VARIANT(SEE VARIANT PARTS LIST) C467 VARIANT(SEE VARIANT PARTS LIST) C468 VARIANT(SEE VARIANT PARTS LIST) C470 VARIANT(SEE VARIANT PARTS LIST) C471 VARIANT(SEE VARIANT PARTS LIST) C472 VARIANT(SEE VARIANT PARTS LIST)
Page 50
Note: Note: The components identified Les composants identifies per un trame et une marque ¡ ¡ ¡ ¡ ¡ sont with shading and a critical symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for critiques pout la securite. Ne les safety.
Page 51
V SERIES COMMON PARTS LISTING REF.NO. PART NO. DESCRIPTION Q014 8-729-422-27 TRANSISTOR 2SD601A-Q Q015 8-729-422-27 TRANSISTOR 2SD601A-Q Q016 8-729-422-27 TRANSISTOR 2SD601A-Q Q017 8-729-216-22 TRANSISTOR 2SA1162-G Q301 8-729-216-22 TRANSISTOR 2SA1162-G Q302 8-729-216-22 TRANSISTOR 2SA1162-G Q303 8-729-216-22 TRANSISTOR 2SA1162-G Q354 8-729-422-27 TRANSISTOR 2SD601A-Q Q356 8-729-216-22 TRANSISTOR 2SA1162-G Q357...
Page 52
Note: Note: The components identified Les composants identifies per un trame et une marque ¡ ¡ ¡ ¡ ¡ sont with shading and a critical symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for critiques pout la securite. Ne les safety.
Page 53
V SERIES COMMON PARTS LISTING REF.NO. PART NO. DESCRIPTION R523 VARIANT(SEE VARIANT PARTS LIST) R524 1-249-429-11 CARBON R525 1-216-071-00 RES, CHIP 8.2K R528 1-216-081-00 RES, CHIP R529 VARIANT(SEE VARIANT PARTS LIST) R530 ¡ 1-208-808-11 RES, CHIP R531 VARIANT(SEE VARIANT PARTS LIST) R532 1-208-760-11 RES, CHIP R533...
S SERIES BOARD VARIANT PARTS LIST The parts on this page belong to the following model(s) only: KV-32S40/34SL40/34SL40C REF.NO. PART NO. DESCRIPTION A BOARD VARIANT LIST: KV-32S40/34SL40/34SL40C * A-1298-630-A A BOARD, COMPLETE CAPACITOR C068 1-164-096-11 CERAMIC CHIP 0.01MF C370 1-163-037-11 CERAMIC CHIP 0.022MF C375 1-165-319-11 CERAMIC CHIP...
Note: Note: The components identified by The components identified manual have been carefully factory-selected with shading and a critical for each set in order to satisfy regulations re- symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for garding X-ray radiation. Should replacement safety.
S SERIES BOARD VARIANT PARTS LIST The parts on this page belong to the following model(s) only: KV-35S40 REF.NO. PART NO. DESCRIPTION A BOARD VARIANT LIST: KV-35S40 * A-1298-645-A A BOARD COMPLETE CAPACITOR C069 1-126-964-11 ELECT 10MF C370 1-163-035-00 CERAMIC CHIP 0.047MF C375 1-165-319-11 CERAMIC CHIP...
Note: Note: The components identified by The components identified manual have been carefully factory-selected with shading and a critical for each set in order to satisfy regulations re- symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for garding X-ray radiation. Should replacement safety.
S SERIES BOARD VARIANT PARTS LIST The parts on this page belong to the following model(s) only: KV-34SL40T REF.NO. PART NO. DESCRIPTION A BOARD VARIANT LIST: KV-34SL40T * A-1298-661-A A BOARD, COMPLETE CAPACITOR C068 1-164-096-11 CERAMIC CHIP 0.01MF C370 1-163-037-11 CERAMIC CHIP 0.022MF C375 1-165-319-11 CERAMIC CHIP...
Note: Note: The components identified by The components identified manual have been carefully factory-selected with shading and a critical for each set in order to satisfy regulations re- symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for garding X-ray radiation. Should replacement safety.
V SERIES BOARD VARIANT PARTS LIST The parts on this page belong to the following model(s) only: KV-34VL65C/34VL65/32V65CND REF.NO. PART NO. DESCRIPTION A BOARD VARIANT LIST: KV-34VL65C/34VL65/32V65CND * A-1298-613-A A BOARD COMPLETE CAPACITOR C461 1-126-966-11 ELECT 33MF C478 1-126-934-11 ELECT 220MF C513 ¡...
Note: Note: The components identified by The components identified manual have been carefully factory-selected with shading and a critical for each set in order to satisfy regulations re- symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for garding X-ray radiation. Should replacement safety.
Page 65
Note: Note: The components identified Les composants identifies per un trame et une marque ¡ ¡ ¡ ¡ ¡ sont with shading and a critical symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for critiques pout la securite. Ne les safety.
Page 66
COMPLETE PARTS LISTING REF.NO. PART NO. DESCRIPTION * A-1316-389-A G BOARD, COMPLETE (KV-32V40/32S40/34SL40/32S45/34SL45 only) * A-1316-390-A G BOARD, COMPLETE (KV-34VL65C only) * A-1316-391-A G BOARD, COMPLETE (KV-32V65CND/34VL65 only) * A-1316-395-A G BOARD, COMPLETE (KV-34SL40C only) * A-1316-396-A G BOARD, COMPLETE KV-34SL40T only) * A-1316-399-A G BOARD, COMPLETE (KV-35S40/35S45/37SL45 only)
Page 67
Note: Note: The components identified Les composants identifies per un trame et une marque ¡ ¡ ¡ ¡ ¡ sont with shading and a critical symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for critiques pout la securite. Ne les safety.
Page 68
COMPLETE PARTS LISTING REF.NO. PART NO. DESCRIPTION R611 ¡ 1-216-373-11 METAL R612 1-215-903-11 METAL R613 1-215-903-11 METAL R614 1-215-903-11 METAL R615 1-215-903-11 METAL R618 1-249-425-11 CARBON 4.7K R619 1-249-425-11 CARBON 4.7K R620 1-249-425-11 CARBON 4.7K R621 1-249-429-11 CARBON R622 1-247-863-91 CARBON R623 ¡...
Page 77
Note: Note: The components identified Les composants identifies per un trame et une marque ¡ ¡ ¡ ¡ ¡ sont with shading and a critical symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for critiques pout la securite. Ne les safety.
Page 84
SERVICE MANUAL MODEL KV-32S40 KV-32S40 KV-32S45 KV-32S45 KV-34SL40T KV-34SL40C KV-34SL40 KV-34SL45 KV-35S40 KV-35S40 KV-35S45 KV-35S45 KV-37SL45 KV-32V40 KV-32V40 KV-32V65 KV-32V65 KV-34VL65 KV-34VL65C KV-35V65 KV-35V65 KV-37VL65 KV-37VL65C SUBJECT: A Board Schematic and Parts List Correct the service manual as shown. File this Supplement with the service manual. AA-2D DEST.