Table of Contents
Advertisement
Quick Links
Outcross
Model No. 07511AA-Serial No. 404700001 and Up
Model No. 07511BA-Serial No. 404700001 and Up
Model No. 07511CA-Serial No. 404700001 and Up
Model No. 07511DA-Serial No. 404700001 and Up
Read this information carefully to learn how to operate the InfoCenter control on your product. You are
responsible for operating the product properly and safely.
Visit www.Toro.com for product safety and operation training materials, accessory information, help finding a
dealer, or to register your product.
Introduction
This guide provides information on using the system
information and controling the system functions.
Contents
Introduction ............................................................... 1
Product Overview ..................................................... 1
Controls ............................................................. 1
Operation .................................................................. 4
Symbols Glossary .............................................. 4
Navigating in the InfoCenter ............................... 6
Using the Operation-Mode Selector.................... 6
Accessing the Protected Menus.......................... 8
Language........................................................ 8
Setting the Service-Due Indicator ....................... 9
Audible Alarms ................................................... 9
Brightness/Contrast ...................................... 10
Setting Up Parameters ..................................... 10
© 2019-The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
™
9060 Series Traction Unit
Product Overview
Controls
InfoCenter Startup Screen
When you start the machine, the startup screen
appears, displaying the corresponding mode icons
that apply.
Note:
screen shows potential icons that could appear on
the screen while operating.
Refer to the Symbols Glossary for all the icon
meanings.
From the any modes home screen, press any button
to access the pop-up menu bar at the bottom of the
screen
Register at www.Toro.com.
Form No. 3431-207 Rev A
The following figure is an example screen; this
(Figure
1).
Original Instructions (EN)
All Rights Reserved *3431-207* A
Printed in the USA
Software Guide
Advertisement
Table of Contents
Related Manuals for Toro 07511AA
Summary of Contents for Toro 07511AA
-
Page 1: Table Of Contents
Read this information carefully to learn how to operate the InfoCenter control on your product. You are responsible for operating the product properly and safely. Visit www.Toro.com for product safety and operation training materials, accessory information, help finding a dealer, or to register your product. - Page 2 Push the status display switch to toggle through the different available screens. See the following figures for the available screens. Note: See your authorized Toro distributor for the Fault Code Manual or the Yanmar ® engine manual for engine faults.
- Page 3 g249938 g249942 Figure 5 Figure 8 Machine hours and Fuel gauge 1. 3-point hitch lifted 4. Current hitch position 2. Maximum 3-point height 5. Minimum work position 1. Machine hours 2. Fuel gauge position for the current, for the current, active active attachment attachment 3.
-
Page 4: Operation
Operation InfoCenter Icon Description (cont'd.) Symbols Glossary Edit the attachment The following table shows the possible symbols for the InfoCenter. Hydraulic circuit 1 InfoCenter Icon Description Attachment Alert Hydraulic circuit 2 Battery More options above Brightness/Contract More options below Brightness Maintenance Contrast Service menu... - Page 5 InfoCenter Icon Description (cont'd.) InfoCenter Icon Description (cont'd.) Exhaust temperature is high due to Stop safely as soon as possible the regeneration Parked or recovery regeneration Fuel level icon—regeneration is requested. Perform the regeneration immediately. Cancel NOx control system malfunction; the machine requires service.
-
Page 6: Navigating In The Infocenter
Navigating in the InfoCenter Using the Operation-Mode Selector Use the following icons to navigate through screens in the InfoCenter. These are used with the buttons on Note: The machine must come to a stop before you the bottom of the InfoCenter display. can change the modes. - Page 7 InchMode™ If Equipped Note: The InchMode setting is available through the use of an optional kit; see your authorized Toro distributor for more information. Use the InchMode setting to aid in the connection of g250708 attachments to the machine. To access the InchMode...
-
Page 8: Accessing The Protected Menus
The factory default PIN code for you machine is either 0000 or 1234. If you changed the PIN code and forgot it, contact your authorized Toro distributor. In the Setup mode, press any button to access the pop-up menu bar at the bottom of the screen (Figure 15). -
Page 9: Setting The Service-Due Indicator
Select the S option from the display ETTINGS Select the save icon menu and select the next screen icon Enter the PIN number (Figure 15) and select the Audible Alarms icon NTER The machine alarm sounds when the operator is out Scroll down to I option and select the ENTER... -
Page 10: Changing The Infocenter Display Brightness/Contrast
Changing the mode. It is adjustable from 1.6 to 33.8 km/hr (1 to 21 mph) in 0.16 km/hr (0.1 mph) increments. InfoCenter Display Maximum Auto Low Ground Speed Brightness/Contrast This allows the supervisor to limit the machine ground You can access the brightness and contrast in the speed when the machine is in the Low Automotive attachment, auto high, auto low, and inchmode. - Page 11 • —the attachment requires hydraulic You can set the minimum speed alarm to remind YDRAULIC power only the operator to maintain speed as soon as it is safe to do so. • —the attachment requires both hydraulic and PTO power. This could be a combination of Note: With the proper parameter settings, you 2 attachments.
- Page 12 (Figure 22). an attachment like an aerator or top dresser. When operating the Toro 1298 aerator, a speed range of Three-Point Turn Around Position 0.16 km/hr (0.1 mph) allows the operator to change the spacing 4.8 mm (3/16 inch) wider or 4.8 mm (3/16 This parameter is only required for 3-point attachments inch) narrower than the parameter setting.
- Page 13 Three-Point Max Work Position Drop Speed This is the highest 3-point hitch position that the PTO This controls the 3-point lower rate. It is adjustable is allowed to rotate when engaged. from 10 to 100% in 10% increments. Note: Raise the attachment and verify that the This helps prevent damage to turf when dropping the PTO drive shaft does not bottom out or separate by attachment into the turf.
- Page 14 It is adjustable from 0 to 25 seconds in 0.1 second increments. Setting up a Toro 1298 ProCore Aerator Use this for attachments like a 3-point rotary mower Move the operation-mode selector to the S...
- Page 15 Set the delay lower time by using the plus or minus icons and select the next screen icon. Select the next screen icon. Set the delay turn-around time by using the plus Select the P engagement method and ADDLE or minus icons and select the next screen icon. select the next screen icon.
- Page 16 For the location, select the 3- option and POINT Confirm the save by selecting the save icon select the next screen icon. Turn the mode selector knob the attachment Select the power source as the PTO and select position. the next screen icon. Select the engagement method as S WITCH select the next screen icon.