Page 1
SERVICE MANUAL East European Model SLV-SE500R/SE700R French Model SLV-SE600B/SE700B/SE800B/SX700B German Model SLV-SE650D/SE700D1/SE800D1/ SX700D/SX800D Italian Model SLV-SE600A/SE700D2/SE800D2 Middle East Model SLV-SE350K/SE500K/SE600N/SE700K/ SE700N/SE800K/SE800N North European Model SLV-SE600E/SE700E2/SE800E/ Photo: SLV-SE800 SX600E/SX700E Spanish Model SLV-SE700E1 UK Model SLV-SE700G/SE700I/SE800G SR MECHANISM • Refer to the SERVICE MANUAL of VHS MECHANICAL ADJUSTMENTS VI for MECHANICAL ADJUSTMENTS.
Page 2
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.
Page 3
Maximum recording/playback time General 10 hrs. in LP mode (with E300 tape) Fast-forward and rewind time Power requirements Approx. 1 min (with E180 tape) 220 - 240 V AC, 50 Hz Power consumption Inputs and outputs 21 W Operating temperature i LINE-1 (TV) 5ºC to 40ºC 21-pin...
TABLE OF CONTENTS Section Title Page Section Title Page Feature Difference ..............4 INTERFACE, IC PIN FUNCTION DESCRIPTION SERVICE NOTE ..............6 5-1. System Control-Video Block Interface (MA-373 BOARD IC162) ..........5-1 GENERAL 5-2. System Control-Servo Peripheral Circuit Interface (MA-373 BOARD IC162) ..........5-1 Getting Started ..............
SERVICE NOTE 1. DISASSEMBLY • This set can be disassembled in the order shown below. Note: Pages in indicated pages in the SERVICE MANUAL. Pages in indicated pages in the VHS MECHANICAL ADJUSTMENT MANUAL VI. Upper Case (Page 2-1) Front Panel Pinch Press Ground Shaft Rear...
SLV-SE350/SE500/SE600/SE650/SE700/SE800/SX600/SX700/SX800 SECTION 1 This section is extracted from SLV-SE800N/K GENERAL instruction manual. (3-868-277-11)
SLV-SE350/SE500/SE600/SE650/SE700/SE800/SX600/SX700/SX800 SECTION 2 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. 2-1. UPPER CASE REMOVAL 2-3. POWER BLOCK (SRV938EK) REMOVAL 1 Two screws 3 Upper case (Case3 TP2) 2 Connector (CN201) 3 Three screws (B3) 1 Connector (CN202) 2 Two screws (Case3 TP2)
SLV-SE350/SE500/SE600/SE650/SE700/SE800/SX600/SX700/SX800 SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM SE700R/SE800K SE500R MA-373 BOARD (SEE PAGE 4-9 to 4-30) EXCEPT SE350/ V IN SE500/SE600/ V OUT SE700R/SE800K/ SX600 IC200 M901 SE350/ L OUT IC162 (1/2) IC162 (2/2) DRUM MOTOR SE600/ (1/2) SX600 R OUT D VS...
SLV-SE350/SE500/SE600/SE650/SE700/SE800/SX600/SX700/SX800 3-3. SERVO/SYSTEM CONTROL BLOCK DIAGRAM CN161 MA-373 BOARD (2/5) (SEE PAGE 4-17) RESET IC162 (2/3) DATA CHECK SERVO/SYSTEM CLOCK CONTROL MTR12V IC160 IC162 uj REC/PB CN101 D110 RESET RESET PULSE GEN. OUTPUT 5.4 Vp-p (56 kHz) POWER D VS DRUM ERR P FAIL FAIL...
SLV-SE350/SE500/SE600/SE650/SE700/SE800/SX600/SX700/SX800 3-5. TUNER BLOCK DIAGRAM MA-373 BOARD (4/5) (SEE PAGE 4-23) EXCEPT SE350/SE500/SE700R TU702 AERIAL (Hi-Fi) VIDEO MOD V (SEE PAGE 3-4) AUDIO VIDEO MOD A TUNER VIDEO (SEE PAGE 3-8) (SEE PAGE 3-3) Q730 EXCEPT SE350/SE500/SE700R MUTE TUNER L Q731 MUTE TUNER R...
SLV-SE350/SE500/SE600/SE650/SE700/SE800/SX600/SX700/SX800 SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING For schematic Diagram: • Caution when replacing chip parts. BOARDS AND SCHEMATIC DIAGRAMS. New parts must be attached after removal of chip. (In addition to this, the necessary note is printed Be careful not to heat the minus side of tantalum capacitor, in each block.) because it is damaged by the heat.
SLV-SE350/SE500/SE600/SE650/SE700/SE800/SX600/SX700/SX800 There are few cases that the part isn't mounted in this model is printed on this diagram. 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS MA-373 (VIDEO, AUDIO, I/O, SERVO/SYSTEM CONTROL, TUNER, MODE CONTROL) PRINTED WIRING BOARD – Ref. No.: MA-373 board; 1,000 series – VIDEO, AUDIO, I/O, SERVO/SYSTEM CONTROL, TUNER, MODE CONTROL MA-373...
SLV-SE350/SE500/SE600/SE650/SE700/SE800/SX600/SX700/SX800 JK-180 (FRONT IN), KK-23 (DIAL TIMER) PRINTED WIRING BOARDS – Ref. No.: JK-180 board, KK-23 board; 1,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram. –SLV-SE500/SE800/SX800 – –SLV-SE800/SX800 – MA-373 VIDEO, AUDIO, I/O, SERVO/SYSTEM CONTROL,...
SLV-SE350/SE500/SE600/SE650/SE700/SE800/SX600/SX700/SX800 DS-91 (MODE CONTROL) PRINTED WIRING BOARD – Ref. No.: DS-91 board; 1,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram. MA-373 VIDEO, AUDIO, I/O, SERVO/SYSTEM CONTROL, TUNER, MODE CONTROL POWER BLOCK (SRV938EK) (POWER SUPPLY)
Page 60
SLV-SE350/SE500/SE600/SE650/SE700/SE800/SX600/SX700/SX800 DS-91 (MODE CONTROL) SCHEMATIC DIAGRAM – Ref. No.: DS-91 board; 1,000 series – DS-91 BOARD EXCEPT SE500/SE800/SX800 CN453 D GND SE500/SE800/SX800 A/D1 GO MA-373 BOARD (8/9) CN450 CN461 A/D1 RTN (SEE PAGE 4-27) DMS_1 A/D2 RTN PLAY DMS_2 A/D2 GO STOP STOP DUAL MODE...
SLV-SE350/SE500/SE600/SE650/SE700/SE800/SX600/SX700/SX800 SRV938EK (POWER SUPPLY) PRINTED WIRING BOARD – Ref. No.: SRV938EK board; 2,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram. SRV938EK BOARD SRV938EK BOARD CN101 CN201 CN202 L101 D101 D102 R251...
SLV-SE350/SE500/SE600/SE650/SE700/SE800/SX600/SX700/SX800 SECTION 6 ERROR CODES 6-1. ERROR CODE INDICATION • Error codes are indicated using the lower 5 digits in the fluorescent display tube. “At this time, Colon “:”between character is not indicated.” Mode code indication when the error has occurred. Error code ERROR CODE No error...
SLV-SE350/SE500/SE600/SE650/SE700/SE800/SX600/SX700/SX800 SECTION 7 ADJUSTMENTS 2-1-3. Set-up of Adjustment During the adjustment, see the Parts Arrangement In this adjustment, PAL or NTSC pattern generator is connected Diagram for Adjustments on Page 7-6. with LINE input signal terminal. When checking with tuner, con- nected AERIAL terminal.
2-1-6. Adjusting Sequence 2-3. SERVO SYSTEM ADJUSTMENT Make the electrical adjustment in the following sequence. 2-3-1. RF Switching Position Adjustment Power supply adjustment (MA-373 BOARD) Purpose: Adjust the interval between A ch and B ch of tape playback out- put. Improve the interchangeability with other tapes and sets.
2-4. AUDIO SYSTEM ADJUSTMENTS RF SWP • Adjust both Lch and Rch. [Connection] Audio Audio level meter or generator distortion meter 600 Ω 47 kΩ Attenuator AUDIO LINE IN Feed signal both AUDIO LINE OUT channelssimultaneously. Fig. 7-2-5. Fig. 7-2-4. 2.
3. Overall Level Characteristic and Distortion Factor 2-4-2. Normal Audio System Adjustment Check • Make adjustment in the SP mode, unless otherwise specified. Purpose: Use a normal VHS cassette for an adjustment tape. Check the record level, play level, and distortion factor against the •...
4. Overall Level Characteristic and Distortion Factor 2-5. PARTS ARRANGEMENT DIAGRAM FOR ADJUSTMENTS Check Purpose: MA-373 BOARD (Side A) Check the record level, play level, and distortion factor against the reference input. CN262 Mode REC and PB (SP mode) Signal 400 Hz, –6.3 dBs Measurement point Audio output terminal...
8-1-2. CHASSIS ASSEMBLY 8-1-3. MECHANISM CHASSIS ASSEMBLY (1) supplied not supplied supplied The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number speci- not supplied fied. Ref. No. Part No. Description Remark Ref.
DS-91 JK-180 8-2. ELECTRICAL PARTS LIST NOTE: The components identified by • Due to standardization, replacements in the • Items marked “*” are not stocked since they mark 0 or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.