Page 3
Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice. Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused.
Page 7
RM-781 ESD protection ESD protection Nokia requires that service points have sufficient ESD protection (against static electricity) when servicing the phone. Any product of which the covers are removed must be handled with ESD protection. The SIM card can be replaced without ESD protection if the product is otherwise ready for use.
Page 9
Our policy is of continuous development; details of all technical modifications will be included with service bulletins. While every endeavour has been made to ensure the accuracy of this document, some errors may exist. If any errors are found by the reader, NOKIA MOBILE PHONES Business Group should be notified in writing/e- mail. Please state: •...
Page 11
RM-781 Nokia 300; Nokia 3000 Service Manual Structure Nokia 300; Nokia 3000 Service Manual Structure 1 General information 2 Service Devices and Service Concepts 3 BB Troubleshooting and Manual Tuning Guide 4 Cellular RF troubleshooting 5 System Module 6 Other peripherals (ie. CWS)
RM-781. For the correct use of the service devices, and the best effort of workbench setup, please refer to various concepts. MJ-300 Module jig Module jig MJ-300 can be used for flashing via USB and RF, battery and system testing. The main functions are: • Powering with external power •...
Interface for CU-4 control unit SS-227 is designed for regional Central Services to be able to use CU-4 with MJ-300 module jig. With SS-227, CU-4 can be used for battery testing. The main functions of SS-227 are: • CU-4 interface adapter to MJ-300 •...
Page 29
• Installation and warranty information SRT-6 Opening tool SRT-6 is used to open phone covers. Note: The SRT-6 is included in the Nokia Standard Toolkit. SS-46 Interface adapter SS-46 acts as an interface adapter between the flash adapter and FPS-20/FPS-21.
Bad conditions often cause bad pictures. Therefore, the camera operation has to be checked in constant conditions or by using a second, known-to-be-good Nokia device as reference. Image quality is hard to measure quantitatively, and the difference between a good and a bad picture can be small. Some training or experience may be needed to detect what is actually wrong.
• The image may be blurred, though it does not show in the viewfinder • Analyse the picture from your PC monitor, full colour setting is recommended • If possible, compare with a picture of the same motive taken with a similar Nokia device Page 3 – 34...
The following equipment is needed for the tests: • Oscilloscope • Function generator (sine waveform) • Phoenix service software and NCS (Nokia Care Suite) • Battery voltage 3.7V Test procedure Audio can be tested using the Phoenix audio routings option. These different audio loop paths can be activated: •...
VREF level ..............................4–12 VDCDCA (Vlow) level ..........................4–13 RF tuning and testing ............................4–13 RF auto tuning and testing with Nokia Care Suite..................4–13 RF auto tuning procedure ..........................4–13 Automatic RF testing with Nokia Care Suite....................4–17 Troubleshooting with Testing And Tuning Tool ..................
High-Band are always both connected before voltage is applied to the phone. Nokia Care Suite preparations Install Testing And Tuning Tool add-on application to Nokia Care Suite. Automatic RF testing and tuning is not possible without this application. There is no more support in Phoenix to auto tune RM-781 product.
Page 95
RM-781 Cellular RF troubleshooting Nokia Care Suite and Testing And Tuning Note: The window appearance may differ depending on the Tool versions Click on the RF Tuning button. The following view opens: Nokia Care Suite and Testing And Tuning Note:...
Page 96
RM-781 Cellular RF troubleshooting Nokia Care Suite and Testing And Tuning Note: The window appearance may differ depending on the Tool versions 10 If no critical errors happen during the low band RF tuning procedure, the following window will pop up: 11 Change the CA-158RS cable to the high band RF connector on the phone PWB.
RM-781 Cellular RF troubleshooting Automatic RF testing with Nokia Care Suite Testing And Tuning Tool add-on application can be used also for non-signalling RF tests. The automatic RF RF auto tuning procedure , but RF Testing should testing procedure is the same as explained in the chapter Testing And Tuning Tool main window instead of RF Tuning .
Figure 10 Blade battery connector Charging This phone is charged through the smaller Nokia standard interface (2.0 mm plug). The wider standard charger plug (3.5 mm) can be used together with a CA-44 charger adapter. Figure 11 Small (right) and wide (left) charger plugs The phone can also be charged via USB.