Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instruction
protection
manual
1. SAFETY
Follow workshop Health & Safety rules, regulations and conditions when using the grease gun.
9
WARNING!Disconnect from air supply before changing accessories or servicing.
ˆ
Maintain the grease gun in good condition.
9
WARNING! Check that the correct air pressure is maintained and not exceeded.
ˆ
Keep air hose away from heat, oil and sharp edges. Check hose for wear before each use and ensure that all connections are secure.
9
Wear appropriate protective clothing. When handling lubricants refer to manufacturer's instructions and conform to local regulations.
9
Dispose of waste grease in accordance with local authority regulations.
9
Keep grease gun clean and in good working order for best and safest performance.
9
Keep children and unauthorised persons away from the work area.
9
DO NOT use the grease gun for a task it is not designed to perform.
8
WARNING! DO NOT use gun if damaged or thought to be faulty. Contact your local service agent.
8
WARNING! Grease is delivered at high pressure. DO NOT point the grease nozzle at yourself or others.
ˆ
Ensure grease nipples are free from dirt or debris before connecting the grease gun.
9
DO NOT operate the trigger until the nozzle is firmly attached to the receiving grease fitting.
8
DO NOT drop, throw, or abuse, the grease gun.
8
DO NOT carry the grease gun by the air hose, or yank the hose from the air supply.
8
DO NOT operate grease gun if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT direct air from the air hose at yourself or others.
8
When not in use, disconnect from air supply and store in a safe, dry, childproof location.
9
2. INTRODUCTION
Die-cast head and body with chromed steel grease tube. Includes rigid extension tube and 4-jaw coupler. Trigger operated continuous flow gun with
3-way fill and air-bleed valve. Accepts 400g grease cartridges, bulk or manual fill.
3. SPECIFICATION
specification
Model no: .........................................................................SA401.V2
Air pressure:.......................................................................60-150psi
Delivery pressure: ....................................................... 1200-5000psi
Air inlet: ................................................................................ 1/4"BSP
Optional 230mm flexible extension tube: ........................ SA40/09A
4. PREPARATION FOR USE
4.1.
Air Supply
Recommended hook-up is shown in fig.1.
4.1.1.
Ensure that the trigger is in the OFF position when connecting to the
air supply.
WARNING! Ensure that the air supply is clean and is between 60-150psi.
ˆ
Too high an air pressure and/or unclean air will shorten the life of the gun
due to excessive wear, and may be dangerous, causing damage and/or
personal injury.
4.1.2.
Drain the compressor air tank daily. Water in the air line will damage the gun.
4.1.3.
Clean compressor air inlet filter weekly.
4.1.4.
Line pressure should be increased to compensate for unusually long air hoses
(over 8 metres). The minimum hose size should be 1/4" internal diameter and
fittings must have compatible dimensions.
4.1.5.
Keep hose away from heat, oil and sharp edges. Check hose for wear and
make certain that all connections are secure.
© Jack Sealey Limited
INSTRUCTIONS FOR
AIR GREASE GUN
SA401.V2
MODEL NO:
spreparation
Original Language Version
SA401.V2| Issue 2(L) 10/11/15
Advertisement
Related Manuals for Sealey SA401.V2
Summary of Contents for Sealey SA401.V2
- Page 1 SA401.V2 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Grit or gum deposits in the tool will reduce power and may be removed by flushing out the gun with gum solvent oil or an equal mixture of SAE10 oil and kerosene. Note: If the SA401.V2 is used with cartridges for a long period, it is possible that the rubber plunger may become damaged. If it is then used with manual or bulk filling systems, the plunger may allow grease to seep from the bottom of the grease tube. To prevent this happening, check the condition of the rubber plunger, and if worn, replace before using a different fill method.
- Page 3 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Sole UK Distributor, Sealey Group. 01284 757500 www.sealey.co.uk Kempson Way, Suffolk Business Park, Bury St.