hit counter script
Download Print this page
Sealey AK467D Instructions

Sealey AK467D Instructions

Low level oil drainers

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction
manual
1. SAFETY
Replace damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Keep the drainer clean, dry and in good condition for best and safest performance.
Wear appropriate protective clothing and eye protection.
If it is necessary to raise the vehicle ensure that it is properly supported. If the vehicle has been raised with a jack, axle stands must be
put in place before working under the vehicle.
Remove the oil drainer and other tools and equipment from underneath the vehicle before lowering it again.
Use drainer in a suitable work area. Keep area clean and tidy, and free from unrelated materials and ensure that there is adequate
lighting.
The work area should have a flat and level surface capable of supporting the weight of the drainer and it's contents.
DO NOT position the drainer in such a way that it becomes a hazard to others in the work area.
Ensure that the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the work area.
Dispose of waste liquids in accordance with local authority regulations.
WARNING! DO NOT allow uncontrolled discharge of fluids which would pollute the environment.
DO NOT use the drainer in wet or damp areas or where condensation is present.
x
DO NOT use the drainer near open flames or other sources of heat.
WARNING! If draining the oil whilst hot, take precautions to prevent against burns, particularly hands, wrists and arms.
2. INTRODUCTION
Low level drainers suitable for use on the forecourt and workshop floor. Steel fabricated unit with a capacity of 64ltr. Fitted with gravity drain tap for
manual discharge. Model No. AK467DXP fitted with rotary pump and hose for faster discharge. Fully portable with two castors, two fixed wheels
and handle for manoeuvring around the workshop.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AK467D . . . . . . . . . . . . . . . . . . . AK467DXP
Capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64ltr . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64ltr
Maximum Pan Height: . . . . . . . . . . . . . . . . . . . . . . . 285mm. . . . . . . . . . . . . . . . . . . . . . . .285mm
Gravity Feed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
Gravity Discharge: . . . . . . . . . . . . . . . . . . . . . . . . . . Yes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
Pump Discharge: . . . . . . . . . . . . . . . . . . . . . . . . . . . No . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
4. ASSEMBLY
4.1.
Assembly
4.1.1. CASTOR WHEELS (fig.1). Bolt a castor wheel to each of the
projecting brackets either side of the handle mount using the
M12 nuts and washers provided.
4.1.2. FIXED WHEELS (fig.2). Insert the special axle bolts through
each wheel so that the wheel is running on the roller bearing.
Mount each wheel by pushing the axle bolt through each of the
tubular axle mounts welded to the back, bottom edge of the
casing. Secure each axle bolt with the M12 lock nuts provided.
DO NOT over tighten.
4.1.3. HANDLE (fig.3). Place the handle into the bracket situated centrally between the two castor
brackets. Align the hole in the end of the handle with the hole in the bracket and insert the
Ø8mm x 40 bolt through both parts. Secure with the M8 nut provided.
© Jack Sealey Limited
INSTRUCTIONS FOR:
LOW LEVEL OIL DRAINERS
AK467D, AK467DXP
MODELS:
Wear eye
protection
fig.1
Original Language Version
Wear protective
gloves
fig.2
fig.3
AK467D, AK467DXP
Wear protective
clothing
Issue: 2 - 12/09/17

Advertisement

loading

Summary of Contents for Sealey AK467D

  • Page 1 Model No: ....... . AK467D ..
  • Page 2 WARNING! Dispose of all waste in accordance with local regulations.  5.3.1. GRAVITY DISCHARGE (AK467D) Attach the discharge hose to the outlet valve at the rear end of the drainer and secure it with the worm drive clip provided. See fig.5.

This manual is also suitable for:

Ak467dxp