Related Manuals for 6K Products DH0606
Summary of Contents for 6K Products DH0606
-
Page 1: Cover Page
OPERATION AND PARTS MANUAL DH0606 14G36 Connect and Cut Hydraulic Chain Information subject to change without notice. -
Page 2: Safety Precaution
⇒ The information in this manual is subject to change without notification. ⇒ This manual is intended for safe operation and maintenance of the 6K Products, 14G36 Connect and Cut Hydraulic Chain Saw. 6K Products, welcomes any and all suggestions on how to improve... -
Page 3: Table Of Contents
Table of Contents Cover page ..................................1 Safety Precaution ................................. 2 Table of Contents ................................. 3 Introduction .................................. 4 Warranty ..................................4 Installation ..................................4 Hydraulic Connections ..............................5 Chain Tension and Sharpening ............................. 6 Sprocket Removal and Replacement ..........................7 Feed Control Adjustment ............................. -
Page 4: Introduction
Introduction Thank you for purchasing a 6K Products product. Our goal is to provide quality products for your job. This manual contains warranty information, installation information, operation instructions, parts ordering information, and service contact information. Warranty This 6K Products product carries a one year or 2000 hour warranty on the 6K Products designed and built components covering material and workmanship. -
Page 5: Hydraulic Connections
After assembling the components as shown in figure 1, position the saw bar square to the log, at the correct height with clearance between the bar guard and the side of the largest log and weld down solidly (Fig. 4). Fig. -
Page 6: Chain Tension And Sharpening
The return hose can be #8 or 1/2” diameter for the first three feet, if a longer hose is required it must be #12 or 3/4” up to thirty feet. If the total return hose length is greater than thirty three feet #16 or 1” hose should be used. The filter must be rated for 20 GPM plus any additional pump flowing into it. -
Page 7: Sprocket Removal And Replacement
Sprocket Removal and Replacement The chain saw sprocket is connected to the shaft with a tapered bushing. To remove the sprocket remove the Cap Screws (Fig. 7, Item 3) and screw them into the Threaded Holes, tighten up to 36 inch pounds to push the Sprocket (Fig. -
Page 8: Feed Control Adjustment
Feed Control Adjustments Connect and Cut saw systems have a control manifold with cartridge valves to limit flow to the saw motor and feed cylinder, and a feed modulating valve to adjust the feed speed based on the saw motor pressure. We have tested the operation of your system to set the valves before shipping so your system should cut any diameter, species, or hardness of wood without stalling the chain in the cut. -
Page 9: Bar Oil Pump Adjustment
Bar Oil Pump Adjustments The DH0144 bar oil pump (Fig. 9) is a single acting pump that can pump up to 32 cc, or 1.08 oz., of bar oil per cycle, enough for about 30 seconds of cutting. There is a hose connected to the feed and motor control valve manifold (Fig. -
Page 10: Operating Instruction
Parts and Service Information For parts and service contact 6K Products. Our hours of operation are 8:00 AM to 4:30 PM, Monday through Friday, Pacific Time excluding holidays. Phone: 360-264-2141... -
Page 11: Main Sub Assembly Parts
MAIN SUB ASSEMBLIES ITEM No. QTY. PART No. DESCRIPTION REMARKS DH0205 HARVESTER BAR, 113 CM OREGON 132HSFL114 DH0206 SAW CHAIN, 80 GAUGE, 126 DRIVE LINKS OREON 18HX DH0130 MAIN FRAME FDTD10 DRILLED WELD DOWN PLATE DH0352 BAR PLATE ASSEMBLY DH0162 FEED CYLINDER ASSEMBLY DH0201 BAR GUARD WELDMENT... -
Page 12: Bar Plate Assembly Parts
DH0624 BAR PLATE ASSEMBLY... -
Page 13: Feed Cylinder Assembly Parts
DH0162 FEED CYLINDER ASSEMBLY... -
Page 14: Bar Oil Pump Assembly Parts
DH0144 BAR OIL PUMP ASSEMBLY... -
Page 15: Feed And Motor Control Manifold Parts
DH0156 FEED and MOTOR CONTROL MANIFOLD... -
Page 16: Bar Oil Tank Assembly Parts
DH0152 BAR OIL TANK ASSEMBLY... -
Page 17: Hose Layout
HOSE LAYOUT ITEM No. QTY. PART No. DESCRIPTION REMARKS DH0182 SAW MOTOR HOSE, 38" OAL #8 - 3000 PSI HOSE DH0349 MANIFOLD TO BAR OIL PUMP HOSE, 24.5" OAL #4 - 3000 PSI HOSE DH0180 OIL TANK TO BAR OIL PUMP HOSE, 12" OAL 4LOLB DH0181 BAR OIL PUMP TO BAR PLATE HOSE, 24.5"...