Table of Contents
Advertisement
Quick Links
SERVICE MANUAL
Ver 1.0 2003.02
HCD-CPX1 is the Amplifier, CD
player, Tape Deck and Tuner section
in CMT-CPX1.
Amplifier section
DIN power output (rated): 55 + 55 W
(4 ohms at 1 kHz, DIN)
Continuous RMS power output (reference):
70 + 70 W
(4 ohms at 1 kHz, 10%
THD)
Inputs
MD (VIDEO) IN (phono jacks):
Sensitivity 450/250 mV,
impedance 47 kilohms
Outputs
CD DIGITAL OUT:
Optical Wavelength:
660 nm
PHONES:
accepts headphones with
an impedance of 8 ohms or
more
SPEAKER:
accepts impedance of
4 ohms
Sony Corporation
9-877-059-01
2003B0500-1
Home Audio Company
C 2003.02
Published by Sony Engineering Corporation
Model Name Using Similar Mechanism
CD Mechanism Type
CD
Base Unit Name
Section
Optical Block Name
Optical Pick-up Name
Tape deck
Model Name Using Similar Mechanism
Section
SPECIFICATIONS
CD player section
Laser
Semiconductor laser
(CD: λ =780 nm)
Emission duration:
continuous
Frequency response
CD: 2 Hz – 20 kHz
Wavelength
780 – 790 nm
Tape deck section
Recording system
4-track 2-channel stereo
Frequency response
50 – 13,000 Hz (±3 dB),
using Sony TYPE I
cassettes
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
87.5 – 108.0 MHz (50 kHz
step)
Antenna
FM wire antenna
Antenna terminals
75 ohms unbalanced
Intermediate frequency
10.7 MHz
COMPACT DISC DECK RECEIVER
HCD-CPX1
AM tuner section
Tuning range
Antenna
Intermediate frequency
General
Power requirements
Power consumption
Dimensions (w/h/d)
Mass
Design and specifications are subject to change
without notice.
AEP Model
UK Model
NEW
CDM55C-K6BD44S
BU-K6BD44S
KSM-213DCP
KSS-213D
NEW
531 – 1,602 kHz
(with the tuning interval
set at 9 kHz)
AM loop antenna, external
antenna terminal
450 kHz
230 V AC, 50/60 Hz
50 W
0.3 W (in Power Saving
mode)
Approx. 174 × 240.5 × 291
mm
Approx. 4.3 kg
Advertisement
Table of Contents
Related Manuals for Sony HCD-CPX1
Summary of Contents for Sony HCD-CPX1
- Page 1 HCD-CPX1 SERVICE MANUAL AEP Model UK Model Ver 1.0 2003.02 HCD-CPX1 is the Amplifier, CD player, Tape Deck and Tuner section in CMT-CPX1. Model Name Using Similar Mechanism CD Mechanism Type CDM55C-K6BD44S Base Unit Name BU-K6BD44S Section Optical Block Name...
-
Page 2: Table Of Contents
AND IN THE PARTS LIST ARE CRITICAL TO SAFE (CDM55C-K6BD44S) ............ 52 OPERATION. REPLACE THESE COMPONENTS WITH 7-9. Base Unit (BU-K6BD44S) ..........53 SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- ELECTRICAL PARTS LIST ....... 54... -
Page 3: Servicing Notes
HCD-CPX1 SECTION 1 SERVICING NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electro- static break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. - Page 4 HCD-CPX1 TAPE MECHANICAL DECK SERVICE POSITION Set up the service position with putting an insulator under the mechanical deck as the figure shown below. tape mechanical deck insulator CD MECHANISM DECK SERVICE POSITION Set up the service position for the CD mechanism deck with disassembling the entire set as the figure shown below.
- Page 5 HCD-CPX1 NOTE ON LEADING THE WIRE (FLAT TYPE) (9 CORE) Lead the wire (flat type) (9 core) properly to prevent the wire from coming out from the right side of the guides on the sub panel or sagging inside of the lid.
- Page 6 HCD-CPX1 CLINCHING THE WIRE (FLAT TYPE) (21 CORE) AMP board heat sink Clinch the wire (flat type) (21 core) to prevent the wire from contacting with the heat sink of the AMP board. HANDLING TWO CABLES FROM THE SUB POWER AND THE SWITCHING REGULATOR TO THE MAIN BOARD Note: Fix two cables with the lead pin and the fabric non woven (10 –...
-
Page 7: General
HCD-CPX1 SECTION 2 This section is extracted from instruction manual. GENERAL • LOCATION OF CONTROLS – Front View – BUTTON DESCRIPTIONS ALPHABETICAL ORDER ?/1 (power) 1 R – Z A – Q TAPE Z (eject) 4 Remote sensor 2 BASS +/– wa... -
Page 8: Setting The Clock
HCD-CPX1 – Remote Control – ALPHABETICAL ORDER BUTTON DESCRIPTIONS ?/1 (power) 4 A – E F – Z TAPE nN (play) 7 CD ws FUNCTION wg TAPE x (stop) 8 CLEAR w; PLAY MODE wa CD NX (play pause) 0... -
Page 9: Disassembly
HCD-CPX1 SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW 3-2. CASE (Page 10) 3-3. FRONT PANEL SECTION (Page 10) 3-4. TC BOARD, 3-5. MAIN BOARD MECHANICAL DECK (Page 11) (Page 11) 3-6. -
Page 10: Case
HCD-CPX1 Note: Follow the disassembly procedure in the numerical order given. 3-2. CASE 4 case 2 three screws × (BVTP3 1 two case screws 1 two case screws 3-3. FRONT PANEL SECTION 3 wire (flat type) (19 core) (CN221) 1 screw ×... -
Page 11: Tc Board, Mechanical Deck
HCD-CPX1 3-4. TC BOARD, MECHANICAL DECK 2 wire (flat type) (8 core) 6 four screws (CN602) × 1 wire (flat type) (19 core) (BVTP3 (CN603) Note: Must not use a magnetic screwdriver to prevent the screws from being magnetized. 7 ground wire lead... -
Page 12: Tuner Unit
HCD-CPX1 3-6. TUNER UNIT 3 bracket 2 two screws × (BVTP3 1 connector (CN990) 5 two screws × (BVTP3 6 tuner unit 4 wire (flat type) (15 core) 2 two screws × (BVTP3 3-7. CD MECHANISM DECK (CDM55C-K6BD44S) 1 two claws... -
Page 13: Loading Board
HCD-CPX1 3-8. LOADING BOARD 2 belt (CDM55) 3 Pull the tray (CDM55D) pushing B . 1 Rotate the gear(A) in the direction of arrow A . 5 loading board 4 two screws (BTP2.6 × 8) 3-9. CAM (CDM55) 3 spacer (55) -
Page 14: Base Unit (Bu-K6Bd44S)
HCD-CPX1 3-10. BASE UNIT (BU-K6BD44S) 6 base unit (BU-K6BD44S) 1 two floating screws (PTPWHM2.6) 2 two screws (BTTP M2.6) 3 two stoppers (BU) 5 two insulators 5 two insulators... -
Page 15: Test Mode
HCD-CPX1 SECTION 4 TEST MODE [CMN (MC) TEST MODE] [SHIP MODE (NO MEMORY CLEAR) ] • This mode is used to check operations of Amplifier. • This mode moves the optical pick-up to the position durable to Procedure: vibration. Use this mode when returning the set to the customer 1. - Page 16 HCD-CPX1 [AGING MODE] 3. Tape Deck Section The sequence during the aging mode is following as below. • This mode can be used for operation check of CD section and If an error occurred, stop display that step. tape deck section.
-
Page 17: Electrical Adjustments
HCD-CPX1 SECTION 5 ELECTRICAL ADJUSTMENTS REC LEVEL ADJUSTMENT DECK SECTION 0 dB=0.775 V Procedure: [FUNCTION] 1. Press the key to select “MD” or “VIDEO”. Note: Confirm each contents of this section first of all. If the results are not satisfied, do the adjustment. -
Page 18: Cd Section
HCD-CPX1 Checking Location: CD SECTION – BD BOARD (Conductor Side) – Note: CD Block is basically constructed to operate without adjustment. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. Use an oscilloscope with more than 10 MΩ impedance. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks. -
Page 19: Diagrams
HCD-CPX1 SECTION 6 DIAGRAMS 6-1. BLOCK DIAGRAM – CD SERVO Section – FILTER DIGITAL SIGNAL PROCESSOR, DIGITAL FILTER, D/A CONVERTER IC101 (1/2) RF AMP, 56 53 FOCUS/TRACKING ERROR AMP IC103 A+3.3V PCMD LRCK INTERFACE RFAC C2PO RFAC RFAC RFAC ASYMMETRY... -
Page 20: Block Diagram - Tuner/Tape Deck Section
HCD-CPX1 6-2. BLOCK DIAGRAM – TUNER/TAPE DECK Section – ANTENNA TUNER UNIT TUNER L-CH (Page 21) FM ANT L-CH FM 75Ω COAXIAL ANT GND R-CH R-CH AM ANT ST DOUT ANT GND ST DIN ST CLK ST CE MUTING ST MUTE... -
Page 21: Block Diagram - Main Section
HCD-CPX1 6-3. BLOCK DIAGRAM – MAIN Section – J801 R-CH HEADPHONE AMP PHONES IC102 HEADPHONE TUNER +9V, RIPPLE FILTER MUTING TC A+9V Q180, 181 Q182 L-CH R-CH (Page 20) MUTING L-CH CONTROL SWITCH (Page 19) Q184, 185 L-CH A/D CONVERTER... -
Page 22: Block Diagram - Display/Power Supply Section
HCD-CPX1 6-4. BLOCK DIAGRAM – DISPLAY/POWER SUPPLY Section – D801 LIQUID CRYSTAL LED DRIVE LED STANDBY (STANDBY) DISPLAY DRIVER Q801 IC803 D802 LED DRIVE LED DSG Q802 5 LCD DATA LIQUID CRYSTAL 7 LCD CLK D803 LED DRIVE DISPLAY 6 LCD CS... -
Page 23: Note For Printed Wiring Boards And Schematic Diagrams
HCD-CPX1 6-5. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • Circuit Boards Location Note on Printed Wiring Board: Note on Schematic Diagram: • X : parts extracted from the component side. • All capacitors are in µF unless otherwise noted. pF: µµF AMP board •... -
Page 24: Printed Wiring Board - Bd Board
HCD-CPX1 6-6. PRINTED WIRING BOARD – BD Board – • See page 23 for Circuit Boards Location. S101 (LIMIT) ON : WHEN THE OPTICAL PICK-UP M101 IS INNER POSITION BD BOARD (SPINDLE) C159 JW621 JR101 R159 JW609 R158 R197 C146... -
Page 25: Schematic Diagram - Bd Board
HCD-CPX1 6-7. SCHEMATIC DIAGRAM – BD Board – • • See page 28 for Waveforms. See page 38 for IC Block Diagrams. R196 2.2k R195 330k R194 C193 C194 C109 C111 R109 C198 1500p 100p C116 C183 C184 C185 C165... -
Page 26: Printed Wiring Board - Tc Board
HCD-CPX1 6-8. PRINTED WIRING BOARD – TC Board – • See page 23 for Circuit Boards Location. • Semiconductor Location MAIN BOARD Ref. No. Location TAPE DECK BLOCK CN211 TC BOARD SUPPLIED WITH THE D681 (Page 29) ASSEMBLED BLOCK CN603... -
Page 27: Schematic Diagram - Tc Board
HCD-CPX1 6-9. SCHEMATIC DIAGRAM – TC Board – • See page 28 for Waveform. REC/PB SWITCHING R602 R604 C607 R609 4.7k 470p 2.2k IC602 CN602 BA3126N RV602 PLAY SW R REC F REC TAPE DECK BLOCK R611 PACK SUPPLIED WITH... - Page 28 HCD-CPX1 • Waveforms – TC Board – – MAIN Board – – BD Board – – AMP Board – – LCD Board – ra IC803 3 (OSC2) 1 IC103 qg (RFAC) (CD play mode) 5 IC101 rd (RFDC) (CD play mode)
-
Page 29: Printed Wiring Boards - Loading/Main Boards
HCD-CPX1 6-10. PRINTED WIRING BOARDS – LOADING/MAIN Boards – • See page 23 for Circuit Boards Location. • Semiconductor Location (Page 26) TC BOARD CN603 MAIN BOARD Ref. No. Location R491 D301 JW364 R556 R451 R448 R449 R555 R490 R554... -
Page 30: Schematic Diagram - Main Board (1/2)
HCD-CPX1 6-11. SCHEMATIC DIAGRAM – MAIN Board (1/2) – • See page 38 for IC Block Diagram. (1/2) CN221 M+11.5V MGND TC TRIG TC CAPM +3.3V C108 R103 TC END-SW 0.0027 3.9k TC HALF-REC D302 TC PLAY C102 C106 1SS355TE... -
Page 31: Schematic Diagram - Loading/Main (2/2) Boards
HCD-CPX1 6-12. SCHEMATIC DIAGRAM – LOADING/MAIN (2/2) Boards – • • See page 28 for Waveforms. See page 38 for IC Block Diagram. (2/2) BACK LIGHT +7V LED GND LCD RESET LCD CLK LCD DATA Q433 C432 DTA123YKA LCD CS... -
Page 32: Printed Wiring Board - Amp Board
HCD-CPX1 6-13. PRINTED WIRING BOARD – AMP Board – • See page 23 for Circuit Boards Location. AMP BOARD (COMPONENT SIDE) AMP BOARD (CONDUCTOR SIDE) D662 D660 C690 R610 FB610 C613 C661 C649 C652 R609 (CHASSIS) (CHASSIS) EP602 C674 EP601... -
Page 33: Schematic Diagram - Amp Board
HCD-CPX1 6-14. SCHEMATIC DIAGRAM – AMP Board – • • See page 28 for Waveforms. See page 38 for IC Block Diagrams. CN601 DIAGNOSTIC SP-RELAY ENABLE DGND D+6.2V DGND D+5V R601 FB601 SCDT R602 SC SHIFT R603 EP601 SC LATCH... -
Page 34: Printed Wiring Boards - Back Light/Lcd/Switch Boards
HCD-CPX1 6-15. PRINTED WIRING BOARDS – BACK LIGHT/LCD/SWITCH Boards – • See page 23 for Circuit Boards Location. • Semiconductor Location Ref. No. Location S804 D801 (CD) D802 R814 D803 D804 S806 D805 (CD) D806 R815 C815 D807 D808 S805... -
Page 35: Schematic Diagram - Back Light/Lcd/Switch Boards
HCD-CPX1 6-16. SCHEMATIC DIAGRAM – BACK LIGHT/LCD/SWITCH Boards – • • See page 28 for Waveform. See page 38 for IC Block Diagram. RV803 RV802 RV801 ROTARY ENCODER ROTARY ENCODER ROTARY ENCODER LCD801 BASS TREBLE VOLUME LIQUID CRYSTAL DISPLAY REMOTE... -
Page 36: Printed Wiring Board
HCD-CPX1 6-17. PRINTED WIRING BOARDS – HP/SP OUT/SUB POWER Boards – • See page 23 for Circuit Boards Location. (CHASSIS) HP BOARD MAIN BOARD CN102 (Page 29) FB803 C820 EP801 NO805 C817 FB801 1-686-793- (11) J801 FB802 PHONES C818 SUB POWER BOARD... -
Page 37: Schematic Diagram - Hp/ Sp Out/Power Boards
HCD-CPX1 6-18. SCHEMATIC DIAGRAM – HP/SP OUT/SUB POWER Boards – FB801 CN701 Lch-1 C817 NO805 L721 0.001 FB706 Lch-2 C701 HP DET 470p J801 HP R (Page 33) PHONES C818 C702 0.001 HP GND 470p FB707 HP L J701 L731... - Page 38 HCD-CPX1 • IC Block Diagrams – BD Board – IC101 CXD3017Q IC103 CXA2647N-T4 ROM/RW DC OFST RFDCI – – ERROR RFDC DIGITAL CORRECTOR ASYMMETRY DIGITAL CORRECTOR OPERATIONAL LRCK AMPLIFIER ANALOG SWITCH PCMD INTERFACE DEMODULATOR – ROM/RW VOFST CONVERTER EMPH XVDD...
- Page 39 HCD-CPX1 – MAIN Board – IC101 LC75342 23 22 21 20 19 18 17 – CONTROL CIRCUIT LOGIC INTERFACE CIRCUIT – – CONTROL – CIRCUIT 11 12 13 14 IC201 BA6956AN CONTROL LOGIC – AMP Board – IC600 CXD9743N 41 40 39 38...
- Page 40 HCD-CPX1 IC618 NJM2870F18 (TE2) IC650, 680 CXD9750L VBBA VBBA VBOOTA VDRVA VDRVA UNDER THERMAL VDDA VOLTAGE SHUT DOWN LOCK–OUT GNDA THERMAL PROTECTION BANDGAP DIAGA REFERENCE PROTECTOR CIRCUIT CROSS OVER DELAY FILTER LOW SIDE HIGH SIDE LEVEL SHIFT LEVEL SHIFT DRIVER...
- Page 41 HCD-CPX1 IC603 PCM1802DBR SINGLE-END/ 5TH ORDER MODE1 VINL 1 DIFFERENTIAL DELTA-SIGMA MODE0 CONVERTER MODULATOR FMT1 VINR 2 FMT0 x16 1/64 SERIAL (x1/128) DECIMATION INTERFACE VREF1 3 SCKI REFERENCE FILTER & VREF2 4 MODE/FORMAT WITH DGND DC CUT CONTROL FILTER DOUT...
-
Page 42: Ic Pin Function Description
HCD-CPX1 6-19. IC PIN FUNCTION DESCRIPTION • MAIN BOARD IC401 M30622MGN-B08FP (SYSTEM CONTROLLER (CD MECHANISM CONTROL)) Pin No. Pin Name Description LCD ON Power on/off control signal output for liquid crystal display “H”: power on RDS DATA Serial data input from the RDS decoder on the tuner unit... - Page 43 HCD-CPX1 Pin No. Pin Name Description LED STANDBY LED drive signal output of the standby indicator “H”: LED on SC DT Serial data output to the digital audio signal processor SC SHIFT Serial data shift clock signal output to the digital audio signal processor...
- Page 44 HCD-CPX1 Pin No. Pin Name Description TC END SW Tape end detect switch input terminal Recording-proof claw (forward/reverse) detect switch and cassette in detect switch input terminal TC HALF/REC/SW (A/D input) MODEL Model setting terminal DEST Destination setting terminal 94, 95...
-
Page 45: Exploded Views
HCD-CP101 SECTION 7 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark may have some difference from the original are seldom required for routine service. -
Page 46: Front Panel Section-1
HCD-CPX1 7-2. FRONT PANEL SECTION-1 not supplied not supplied lid (TC) section front panel section-2 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-244-021-01 SPRING (LID TC), TORSION 4-244-014-01 LEVER (EJECT) 1-796-456-31 DECK, MECHANICAL 4-244-023-01 SPRING (EJECT), COMPRESSION... -
Page 47: Front Panel Section-2
HCD-CPX1 7-3. FRONT PANEL SECTION-2 not supplied not supplied not supplied (HP board) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-240-765-01 KNOB, TUNING 1-776-183-11 WIRE (FLAT TYPE) (19 CORE) 4-240-764-01 KNOB, VOLUME A-4731-251-A SWITCH BOARD, COMPLETE 4-240-763-01 KNOB, BASS 4-951-620-01 SCREW (2.6X8), +BVTP... -
Page 48: Lid (Tc) Section
HCD-CPX1 7-4. LID (TC) SECTION not supplied (back light board) not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-4955-421-1 LID (TC) ASSY 1-686-791-11 LCD BOARD 4-236-666-01 CUSHION (LCD) 4-951-620-01 SCREW (2.6X8), +BVTP 4-244-026-01 SHEET, DIFFUSION... -
Page 49: Chassis Section-1
HCD-CPX1 7-5. CHASSIS SECTION-1 not supplied chassis section-2 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-4731-317-A MAIN BOARD, COMPLETE 7-685-646-79 SCREW +BVTP 3X8 TYPE2 TT (B) 7-685-645-79 SCREW +BVTP 3X6 TYPE2 TT (B) -
Page 50: Chassis Section-2
HCD-CPX1 7-6. CHASSIS SECTION-2 chassis section-3 not supplied CDM55C-K6BD44S not supplied The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No. -
Page 51: Chassis Section-3
HCD-CPX1 7-7. CHASSIS SECTION-3 not supplied not supplied not supplied (SP out board) not supplied not supplied The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. -
Page 52: Cd Mechanism Deck Section (Cdm55C-K6Bd44S)
HCD-CPX1 7-8. CD MECHANISM DECK SECTION (CDM55C-K6BD44S) not supplied M201 BU-K6BD44S not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-224-894-12 TRAY (CDM55D) 4-227-218-21 HOLDER (AT) 1-674-336-21 LOADING BOARD X-4953-195-3 PULLEY (AT) ASSY 4-220-229-02 LEVER (SW) -
Page 53: Base Unit (Bu-K6Bd44S)
HCD-CPX1 7-9. BASE UNIT SECTION (BU-K6BD44S) M101 M102 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No. Part No. -
Page 54: Electrical Parts List
HCD-CPX1 SECTION 8 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service. - Page 55 HCD-CPX1 BACK LIGHT Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < DIODE > L670 1-424-777-11 INDUCTOR 10uH D611 8-719-988-61 DIODE 1SS355TE-17 < TRANSISTOR > D621 8-719-988-61 DIODE 1SS355TE-17 D650 6-500-131-01 DIODE LI116 Q691 8-729-602-36 TRANSISTOR...
- Page 56 HCD-CPX1 BACK LIGHT Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < LED > C198 1-104-665-11 ELECT 100uF D806 8-719-075-50 LED SELS6B14C-TP5 (LCD BACK LIGHT) < CONNECTOR > D807 8-719-075-50 LED SELS6B14C-TP5 (LCD BACK LIGHT) D808...
- Page 57 HCD-CPX1 LOADING MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < LIQUID CRYSTAL DISPLAY > R192 1-216-839-11 METAL CHIP 1/10W R193 1-216-847-11 METAL CHIP 150K 1/10W LCD801 1-805-113-11 DISPLAY PANEL, LIQUID CRYSTAL R194 1-216-843-11 METAL CHIP...
- Page 58 HCD-CPX1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C155 1-126-960-11 ELECT C156 1-126-960-11 ELECT < CONNECTOR > C157 1-126-960-11 ELECT CN101 1-568-838-11 CONNECTOR, FFC 21P C158 1-130-476-00 MYLAR 0.0027uF 5% CN102 1-785-316-11 PIN, CONNECTOR (STRAIGHT) 4P...
- Page 59 HCD-CPX1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R182 1-216-826-11 METAL CHIP 2.7K 1/10W < JACK > R183 1-216-833-11 METAL CHIP 1/10W J101 1-770-272-11 JACK, PIN 2P (MD (VIDEO) IN) R184 1-216-821-11 METAL CHIP...
- Page 60 HCD-CPX1 MAIN SP OUT SUB POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R453 1-216-809-11 METAL CHIP 1/10W SP OUT BOARD R454 1-216-809-11 METAL CHIP 1/10W ************* R455 1-216-809-11 METAL CHIP 1/10W R456 1-216-809-11 METAL CHIP 1/10W <...
- Page 61 HCD-CPX1 SWITCH Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R852 1-216-809-11 METAL CHIP 1/10W A-4731-251-A SWITCH BOARD, COMPLETE R853 1-216-809-11 METAL CHIP 1/10W R854 1-216-809-11 METAL CHIP 1/10W *********************** R855 1-216-809-11 METAL CHIP 1/10W < CAPACITOR >...
- Page 62 HCD-CPX1 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C646 1-130-486-00 MYLAR 0.018uF R609 1-216-825-11 METAL CHIP 2.2K 1/10W R610 1-216-832-11 METAL CHIP 8.2K 1/10W C647 1-126-964-11 ELECT 10uF R611 1-216-837-11 METAL CHIP 1/10W C651 1-126-947-11 ELECT...
- Page 63 HCD-CPX1 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MISCELLANEOUS ************** 1-777-989-11 CORD (WITH CONNECTOR) 1-796-456-31 DECK, MECHANICAL 1-824-192-11 WIRE (FLAT TYPE) (8 CORE) 1-773-110-11 WIRE (FLAT TYPE) (19 CORE) 1-776-183-11 WIRE (FLAT TYPE) (19 CORE)
- Page 64 HCD-CPX1 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...