Makita GA9050R Instruction Manual
Hide thumbs
Also See for GA9050R:
- Instruction manual (104 pages) ,
- Instructions manual (8 pages) ,
- Instruction manual (40 pages)
Related Manuals for Makita GA9050R
Summary of Contents for Makita GA9050R
- Page 1 INSTRUCTION MANUAL Angle Grinder GA7050 GA7050R GA9050 GA9050R 010638 DOUBLE INSULATION IMPORTANT: Read Before Using.
-
Page 2: Specifications
Directive, Waste Electric according to EN60745: Electronic Equipment Model GA7050, GA7050R, GA9050, GA9050R implementation in accordance with national law, electric equipment that Sound pressure level (L ) : 94 dB (A) have reached the end of their life must Sound power level (L... - Page 3 Yasushi Fukaya Work mode : disc sanding Director Vibration emission (a ) : 2.5 m/s h,DS Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium Uncertainty (K) : 1.5 m/s ENG902-1 GEA005-3 The declared vibration emission value has been • General Power Tool Safety...
-
Page 4: Grinder Safety Warnings
When operating a power tool outdoors, use an 20. Disconnect the plug from the power source extension cord suitable for outdoor use. Use and/or the battery pack from the power tool of a cord suitable for outdoor use reduces the risk before making any adjustments, changing of electric shock. - Page 5 The rated speed of the accessory must be at 12. Never lay the power tool down until the least equal to the maximum speed marked on accessory has come to a complete stop. The the power tool. Accessories running faster than spinning accessory may grab the surface and pull their rated speed can break and fly apart.
- Page 6 Safety Warnings Specific for Grinding and Abrasive d) Do not restart the cutting operation in the Cutting-Off Operations: workpiece. Let the wheel reach full speed and a) Use only wheel types that are recommended carefully re-enter the cut. The wheel may bind, for your power tool and the specific guard walk up or kickback if the power tool is restarted in designed for the selected wheel.
-
Page 7: Functional Description
23. Do not leave the tool running. Operate the tool FUNCTIONAL DESCRIPTION only when hand-held. 24. Do not touch the workpiece immediately after operation; it may be extremely hot and could CAUTION: burn your skin. Always be sure that the tool is switched off and •... - Page 8 (in the C direction). To stop the tool from the locked position, pull the switch trigger fully (in the B direction), then release it. Indication lamp (For model GA7050R/GA9050R) 1. Indication lamp 010642 Screw the side grip securely on the position of the tool as shown in the figure.
- Page 9 For tool with clamp lever type wheel guard WARNING: Never use a more than 6.5 mm thick grinding • 1. Wheel guard wheel. 2. Bearing box 3. Nut Super flange 4. Lever Models with the letter F are standard-equipped with a super flange.
-
Page 10: Operation
Mount inner flange , abrasive wheel/Multi-disc and NEVER use tool with wood cutting blades and • Ezynut onto the spindle so that Makita Logo on Ezynut other sawblades. Such blades when used on a faces outside. grinder frequently kick and cause loss of control leading to personal injury. - Page 11 ALWAYS use guard with wire wheel brushes, • Grinding and sanding operation assuring diameter of wheel fits inside guard. Wheel can shatter during use and guard helps to reduce chances of personal injury. 1. Wire wheel brush 15° 010648 ALWAYS hold the tool firmly with one hand on rear handle and the other on the side handle.
-
Page 12: Maintenance
2. Inhalation vent accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. 010653... - Page 13 Side grip Wheel guard for Depressed center grinding wheel/Multi-disc / Wire wheel brush Inner flange / Super flange*1*2 Depressed center grinding wheel/Multi-disc Lock nut / Ezynut*1*2 Wheel guard for Abrasive cut off wheel / Diamond wheel *3 Inner flange 78 (Australia and New Zealand only)*4 Abrasive cut off wheel / Diamond wheel Outer flange 78 (Australia and New Zealand only)*4 Rubber pad...
- Page 14 NOTE: Some items in the list may be included in the tool • package as standard accessories. They may differ from country to country.
- Page 16 Makita Jan-Baptist Vinkstraat 2, 3070, Belgium Makita Corporation Anjo, Aichi, Japan www.makita.com 884937E223...