PRODUCT MODEL NUMBERS
KDRS807S
KDSS907S
KDRS807X
KDSS907X
GAS SUPPLY REQUIREMENTS
Provide a gas supply line of
" (1.9 cm) rigid pipe
to the range location. A smaller size pipe on longer
runs may result in insufficient gas supply. Pipe-joint
compounds that resist the action of LP gas must be
used. Do not use TEFLON
®†
tape. With LP gas,
piping or tubing size can be
" (1.3 cm) minimum.
Usually, LP gas suppliers determine the size and
materials used in the system. If local codes permit,
a new CSA design-certified, 4 ft - 5 ft (122 -
152.4 cm) long,
" (1.3 cm) or
flexible metal appliance connector may be used for
connecting range to the gas supply line. A
(1.3 cm) male pipe thread is needed for connection
to the female pipe threads of the inlet to the
appliance pressure regulator. The supply line must
be equipped with a manual shutoff valve. This valve
should be located in the same room but external to
the range. It should be in a location that allows ease
of opening and closing.
ELECTRICAL REQUIREMENTS
When a 4-wire or 3-wire, single phase 120/240 volt,
60 Hz, AC only electrical supply is available, a 50-
amp maximum circuit protection is required. When
a 4-wire or 3-wire single phase 120/208 volt 60 Hz,
AC only electrical supply is available, a 40-amp
maximum circuit protection is required, fused on
both sides of the line. A separate circuit is
recommended. A time-delay fuse or circuit breaker
is recommended.
†®TEFLON is a registered trademark of E.I. Du Pont
Nemours and Company.
SLIDE-IN COUNTERTOP PREPARATION
30"
(76.2 cm)
30 ¾"
(78.1 cm)
INSTALLATION CLEARANCES
F
e r
e
s
a t
n
d
n i
g
R
a
n
13" (33 cm) upper
cabinet depth
30" (76.2 cm) min.
opening width
18" (45.7 cm)
upper cabinet
30" (76.2 cm)
to countertop
min. opening
width
8"
5" (12.7 cm) min.
(20.3 cm)
clearance from
both sides of the
8"
range to the side
(20.3 cm)
wall or other
combustible
7" (17.8 cm)
material.
This shaded area
recommended for
installation of
1 "
rigid gas pipe.
(3.8 cm)
4 "
(11.4 cm)
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
®
30" Freestanding and Slide-In Dual Fuel Range
PRODUCT DIMENSIONS
5 "
(14.6 cm)
" (1.9 cm) I.D.,
"
*Range can be raised approximately
1" (2.5 cm) by adjusting the leveling legs.
**When installed in a 24" (61 cm) base cabinet
with 25" (63.5 cm) countertop; front of oven
door protrudes 1" (2.5 cm) beyond 24"
(61 cm) base cabinet.
The cooktop sides of the slide-in range fit over the
cutout edge of your countertop.
"
If you have a square finish (flat) countertop and the
(1.0 cm)
opening width is 30" (76.2 cm), no countertop
preparation is required.
Formed front-edged countertops must have molded
edge shaved flat
opening.
g
e
s
For minimum
clearance to top
of the cooktop,
see NOTE.
18" (45.7 cm)
upper cabinet
to countertop
Cabinet door
This shaded area
5" (12.7 cm) min.
or hinge
recommended
clearance from
should not
for installation
both sides of the
extend into
of outlet or
range to the side
the cutout.
junction box.
4 "
(11.4 cm)
This shaded area
recommended for
installation of
rigid gas pipe.
Available
area for
gas and
electric
installation.
Freestanding Range
30"
(76.2 cm)
Model/serial number
27¼"
plate (located on the
(69.2 cm) max.
right-hand side
from handle to
oven door trim)
standoff at
back of range**
" (1.0 cm) from each front corner of
l S
d i
- e
n I
R
a
n
g
e
13" (33 cm) max.
upper cabinet depth
30" (76.2 cm) min.
opening width
" (1.9 cm)
radius both corners
30" (76.2 cm)
min. opening
width
6"
(15.2 cm)
6"
wall or other
(15.2 cm)
combustible
7" (17.8 cm)
material.
1 "
(3.8 cm)
4 "
(11.4 cm)
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Slide-in Range
30
"
(77.6 cm)
36" (91.4 cm)
cooktop trim
height with
23" (58.4 cm)
leveling legs
countertop
screwed all
notch to rear
the way in*
of countertop
41 "
(106 cm)
overall height
with leveling
legs screwed
all the way in*
27¼" (69.2 cm) max.
(27¹¹⁄ " [70.3 cm]
on model KDSS907XSP)
from handle to standoff
at back of range**
*Range can be raised approximately
1" (2.5 cm) by adjusting the leveling legs.
**When installed in a 24" (61.0 cm) base cabinet
with 25" (63.5 cm) countertop; front of oven
door protrudes 1 " (4.4 cm) (2
models KDRS807XSP and KDSS907XSP)
beyond 24" (61.0 cm) base cabinet.
Tile countertops may need trim cut back
from each front corner and/or rounded edge flattened.
If countertop opening width is greater than
30" (76.2 cm), adjust the
Countertop must be level. Place level on countertop, first
side to side; then front to back. If countertop is not level,
range will not be level. Range must be level for
satisfactory baking conditions.
s
NOTE: 24" (61 cm) minimum when
bottom of wood or metal cabinet is
covered by not less than
For minimum
clearance to top
(0.64 cm) flame retardant millboard
of the cooktop,
see NOTE.
covered with not less than No. 28
MSG sheet steel, 0.015" (0.4 mm)
stainless steel, 0.024" (0.6 mm)
22
" (58.3 cm)
opening depth
aluminum or 0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance
between the top of the cooking
Cabinet door
This shaded area
platform and the bottom of an
or hinge
recommended
for installation
should not
uncovered wood or metal cabinet.
extend into
of outlet or
the cutout.
junction box.
If installing a range hood or
4 "
microwave hood combination above
(11.4 cm)
the range, follow the range hood or
microwave hood combination
Available
installation instructions for
area for
gas and
dimensional clearances above the
electric
installation.
cooktop surface.
35 " (90.5 cm)
height to underside
of cooktop edge
with leveling legs
screwed all
the way in*
Model/serial
number plate
(located on the
right-hand side
oven door trim)
30"
(76.2 cm)
" [5.5 cm] on
" (1.0 cm)
" (1.0 cm) dimension.
"
Ref. W10246120C
1/28/11