hit counter script
Acer Altos BrainSphere P10 F7 SFF User Manual
  1. Manuals
  2. Brands
  3. Acer Manuals
  4. Desktop
  5. Altos BrainSphere P10 F7 SFF
  6. User manual
Acer Altos BrainSphere P10 F7 SFF User Manual

Acer Altos BrainSphere P10 F7 SFF User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Altos
BrainSphere P10 F7 SFF
User Guide

Advertisement

Table of Contents
loading

Related Manuals for Acer Altos BrainSphere P10 F7 SFF

Summary of Contents for Acer Altos BrainSphere P10 F7 SFF

  • Page 1 Altos BrainSphere P10 F7 SFF User Guide...

  • Page 2: System Setup

    System setup System notes Thank you for purchasing your Altos Workstation. This user guide is intended as a reference for experienced Workstation technicians and helps detail many of the features available in Altos Workstations. For more detailed information about any particular component or software solution, you may consult the technical specifications or the user manual for that application.
  • Page 3 System component identification Altos BrainSphere P10 F7 SFF Front configuration: 12L SFF Chassis 編號 說明 USB 3.2 Gen 1 埠 x 2 USB 2.0 埠 x 2 音源輸入/輸出孔 USB 3.2 Gen1 埠(Type C) 電源按鈕/指示燈 Green ON: 系統開機 Off: 系統關機 DVD CD-ROM (選配)
  • Page 4 Specification introduction  ® Processor type Intel Core™ i9/i7/i5/i3 series Processors, TDP Up to 65W Number of processors On-board Devices Chipset Intel ® H570 Chipset SATA 4 SATA3 (6 Gb/s) ports SATA RAID Intel onboard software RAID 0, 1, 5, 10 (only supports Windows OS) ®...
  • Page 5 Motherboard Layout...
  • Page 7 I/O Panel...
  • Page 8 Installing the CPU...
  • Page 10 Installing Memory Modules (DIMM)
  • Page 11 Installing Memory Modules (DIMM)
  • Page 12 Expansion Slots (PCI Express Slots)
  • Page 13 Jumpers Setup...
  • Page 14 Onboard Headers and Connectors...
  • Page 20 M.2_SSD Module Installation Guide...
  • Page 22 M.2 WiFi/BT Module and Intel® CNVi (Integrated WiFi/BT) Installation Guide...

  • Page 23: Setting Up The System

    Setting up the system Pre-installation requirements Selecting a site Before unpacking and installing the system, select a suitable site for the system for maximum efficiency. Consider the following factors when choosing a site for the system:  Near a grounded power outlet. ...

  • Page 24: Turning On The System

    Turning on the system After making sure that you have properly set up the system, applied power and connected all the necessary peripherals, you can now power on the system. Follow the procedure below. 。 Press the power button The system starts up and displays a welcome message on the monitor. After that, a series of power-on self-test (POST) messages appears.
  • Page 25 Note: If you have gone through the preceding actions and the system still fails to boot, ask your dealer or a qualified technician for assistance.

  • Page 26: Turning Off The System

    Turning off the system There are two ways to turn off the Workstation—via software or via hardware. The software procedure below applies to a system running on a Windows OS. For other shutdown procedures, refer to the related user documentation. To turn off the system via software: Press <Ctrl>...

  • Page 27: System Troubleshooting

    System troubleshooting Resetting the system Before going through in-depth troubleshooting, attempt first to reset the system using one of the methods below. Perform Purpose To do this Soft boot To clear the system memory and Press <Ctrl> + <Alt> + <Del> reload the operating system.

  • Page 28: Initial System Startup Problems

    Initial system startup problems Problems that occur at initial system startup are usually caused by an incorrect installation or configuration. Hardware failure is a less possible cause. If the problem you are experiencing is with a specific application. Initial troubleshooting checklist ...

  • Page 29: Hardware Diagnostic Testing

    Hardware diagnostic testing This section provides a detailed approach to identifying a hardware problem and its cause. Checking the boot-up status Caution: Before disconnecting any peripheral cables from the Workstation, turn off the system and any peripheral devices. Failure to do so can cause permanent damage to the system and/or the peripheral device.

  • Page 30: Specific Problems And Corrective Actions

    Specific problems and corrective actions Listed below are specific problems that may arise during the use of your Workstation and their possible solutions Confirming loading of the operating system Once the system boots up, the operating system prompt appears on the screen. The prompt varies according to the operating system.
  • Page 31 Optical drive tray cannot be ejected Insert the tip of a paperclip into the small hole on the optical drive. Slowly pull the tray out from the drive until the tray is fully extended. Optical drive cannot read a disc Do the following: ...
  • Page 32  Verify that the software is properly configured for the system.  Refer to the software installation and operation documentation for instructions on setting up and using the software. Try a different version of the software to see if the problem is with the copy you are using.
  • Page 33 display monitor or the video controller may be defective. Contact your local Altos representative or authorized dealer for technical assistance.

  • Page 34: Information For Your Safety And Comfort

    Notices Information for your safety and comfort Safety instructions Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. Turning the product off before cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
  • Page 35  Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind onto or into the product. ...
  • Page 36  Use the product only with the supplied power supply cord set. If you need to replace the power cord set, make sure that the new power cord meets the following requirements: detachable type, UL listed/CSA certified, VDE approved or its equivalent, 4.6 meters (15 feet) maximum length.
  • Page 37 Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle.

  • Page 38: Regulations And Safety Notices

    Regulations and safety notices Laser compliance statement The CD or DVD drive used with this computer is a laser product. The CD or DVD drive's classification label (shown below) is located on the drive. CLASS 1 LASER PRODUCT CAUTION: INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM.
  • Page 39 List of applicable countries This device must be used in strict accordance with the regulations and constraints in the country of use. For further information, please contact local office in the country of use. Please see http://ec.europa.eu/enterprise/rtte/implem.htm or the latest country list. Note: The following sections are applicable only to Class A systems FCC notice Class B...
  • Page 40 Caution Changes or modifications not expressly approved by the manufacture could void the user’s authority, which is granted by the Federal Communications Commission, to operate this computer. Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Table of Contents