Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instruction
protection
manual
1. SAFETY
WARNING! Ensure Health and Safety, local authority and general work shop practice regulations are adhered to when using tools.
‰
DO NOT use tool if damaged.
8
Maintain tool in good and clean condition for best and safest performance.
9
Wear approved eye protection. A full range of personal safety equipment is available from your Sealey stockist.
9
Wear suitable clothing to avoid snagging. DO NOT wear jewellery and tie back long hair.
9
DO NOT attempt to start engine or move vehicle, whilst tools are fitted and work is in progress.
8
Ensure any disconnected fuel pipes are plugged to avoid spillage.
9
Account for all tools and parts being used, DO NOT leave them in or near the engine. Return all parts to the case and store this in a safe,
9
dry, childproof location.
IMPORTANT: These instructions are provided as a guide only. Always refer to the vehicle manufacturer's service instructions, or a
proprietary manual, to establish the current procedure and data.
WARNING! The warnings referred to in this guide cannot cover all possible conditions and situations that may occur. It must be
‰
understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.
2. INTRODUCTION
A comprehensive set suitable for removing stubborn glow plugs. Ideal for removing plugs that have been unscrewed, but seized, due to
residue build-up or where the filament has been distorted. Quick and effective method, saving time and money. Supplied in storage case.
3. SPECIFICATION
Model no ..................................................................... VS313
External clamping collets ....................... 2.7, 3.6, 5(x2), 6mm
4. OPERATION
fig.1
Note: Ensure the glow plug has been fully unscrewed from the cylinder head, if not damage to the threads in the cylinder head may
occur.
4.1.
Take the correct sized glow plug collet (fig.1.4) and insert it through the appropriately sized sleeve (fig.1.1). Ensure the flange on the
sleeve is the same side as the thread on the collet.
Note: The glow plug may not take an external collect but has the internal recess to accept the internal collet (fig.1.2).
4.2.
Screw the collet into the tool (fig.1.3, screw back the pressure screw (fig.3) to allow the collet to be screwed fully home.
4.3.
Insert the collet over the end of the glow plug or inside the glow plug (dependant on the type of collet needed).
4.4.
Screw down the pressure screw so the collet tightens securely to the glow plug.
© Jack Sealey Limited
GLOW PLUG PULLER SET
VS313
MODEL NO:
fig.2
Original Language Version
VS313 Issue:3 ( H,F) 11/09/20
Advertisement
Related Manuals for Sealey VS313
Summary of Contents for Sealey VS313
- Page 1 VS313 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...