Page 1
1. Precautions 2. Product specifi cations 3. Disassembly and Reassembly 4. Troubleshooting 5. Exploded View & Part List 6. Wiring Diagram LA32A330J1X / LA40A330J1X Refer to the service manual in the GSPN (see the rear cover) for the more information.
..................4-6. HOW TO UPGRADE 4-22 5. Exploded View & Part List ..................5-1 5-1. LA32A330J1X Exploded View ..................5-1 5-2. LA40A330J1X Exploded View ..................5-3 5-3. LA32A330J1X Parts List ....................5-5 5-4. LA40A330J1X Parts List ....................5-30 6. Wiring Diagram ......................6-1 6-1.
Page 5
3. Disassembly and Reassemble 3. Disassembly and Reassemble This section of the service manual describes the disassembly and reassembly procedures for the LA32A330J1X LCD TV. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 3-1. Disassembly Cautions: 1.
Page 6
3. Disassembly and Reassemble Description Picture Description Screws 3. Remove Screw from the stand BRKT and lift up the stand BRKT. 4. Disonnect cable from the boards. 5. Remove the screws of Scaler board’s shield case and boards.
Page 7
3. Disassembly and Reassemble Description Picture Description Screws 6. Remove screws and Lift up the Lod pa...
Page 8
3. Disassembly and Reassemble Description Picture Description Screws 7. Remove the screws of Stand BKLT. Lift up the Stand BKLT. 8. Remove the Bracket of Boards * Caution: Don’t force yourself on wall mount bracket during disassembly. It may be deformationed.
Page 9
3. Disassembly and Reassemble Description Picture Description Screws 9. Remove the screws on Panel. Reassembly procedures are in the reverse order of disassembly procedures. ※...
1. Precautions 1. Precautions 1-1. Safety Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1-1. Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
1. Precautions 1-2. Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1. Precautions 1-4. Installation Precautions For safety reasons, more than two people are required for carrying the product. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperature may cause fire.
2. Product specifications 2. Product specifications 2-1. Feature & Specifications Model LA32A330J1X Feature RF, 3-HDMI, 2-Component, 2-AV, 1-S-Video,1- D-SUB,1-Headphone,1-Audio output � Brightness : 450cd/m � Contrast Ratio : 10000:1 � Response time : 8ms � Dynamic contrast, Super-PVA � PIP(in HDMI 1, 2, Component 1, PC Mode and Sub picture is available only in TV analog mode) �...
Page 68
2. Product specifications Model LA40A330J1X Feature RF, 3-HDMI, 2-Component, 2-AV, 1-S-Video,1- D-SUB,1-Headphone,1-Audio output � Brightness : 450cd/m � Contrast Ratio : 8000:1 or 2000:1 � Response time : 8ms � Dynamic contrast, Super-PVA � PIP(in HDMI 1, 2, Component 1, PC Mode and Sub picture is available only in TV analog mode) �...
Page 69
2. Product specifications CHANNEL FREQUENCY TABLE OUTPUT FREQUENCY : ANALOG fv:45.75MHz, fs:41.25MHz DIGITAL Fc:44MHz TUNING STEP SIZE : FIRST PLL 250KHz SECOND PLL 62.5KHz OSD CH NO CH NO CH NO CH NO Air-DTV Air-NTSC BAND Cable STD BAND Cable HRC Cable IRC 72.
Page 70
2. Product specifications OSD CH NO CH NO CH NO CH NO Air-DTV Air-NTSC BAND Cable STD BAND Cable HRC Cable IRC 499.25 ULTRA 498.00 499.25 505.25 ULTRA 504.00 505.25 511.25 ULTRA 510.00 511.25 517.25 ULTRA 516.00 517.25 523.25 ULTRA 522.00 523.25 529.25...
2. Product specifications 2-3. Spec Comparison to the Old Models Coral Model Jasmin (LA40S86B) (LN32A330J1X / LN40A330J1X) Design Display Type LCD TV LCD TV Built-in Tuner Resolution 1366 x 768 1366 x 768 LCD Panel TFT LCD Panel 50Hz TFT LCD Panel 50Hz Screen Size 40”...
Page 72
Remote Control & Batteries BN59-00686A (AAA x 2) Power Cord 3903-00145 Cover-Bottom BN63-03665B Owner’s Instructions BN68-01538A Samsung Electronics Service center Cleaning Cloth BN63-01798A Warranty Card / Registration Card / Safety Guide Manual 6801-001011 (Not available in all locations) Stand Screw x 4...
4. Troubleshooting 4. Troubleshooting 4-1. Troubleshooting Check the various cable connections first. • Check to see if there is a burnt or damaged cable. • Check to see if there is a disconnected or loose cable connection. • Check to see if the cables are connected according to the connection diagram. Check the power input to the Main Board.
Page 74
4. Troubleshooting 4-1-1. No Power The LEDs on the front panel do not work when connecting the power cord. The SMPS relay does not work when connecting the power cord. Symptom The units appears to be dead. The IP relay or the LEDs on the front panel does not work when connecting the power cord if the cables are improperly connected or the Main Board or SMPS is not functioning.
Page 75
Does the digital data appear at the Check a IC6001. output of LVDS (R6048~6045_FBE)? Change a main PCB ass’y Check a LVDS cable? Replace a lcd panel? Please, Call to Samsung Co. LTD. Caution Make sure to disconnect the power before working on the IP board.
Page 77
4. Troubleshooting 4-1-3. No Video (HDMI - Digital Signal) Symptom Audio is normal but no picture is displayed on the screen. Check the HDMI source Major Check the M-star checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Power Indicator is off.
Page 78
4. Troubleshooting WAVEFORMS Digital Output Data Signal of HDMI(Data)
Page 79
[4] Does the signal appear at C5068 Change a main PCB ass’y. of IC5001? Check the LVDS cable? Replace the LCD panel? Please, Call to Samsung Co. LTD. Caution Make sure to disconnect the power before working on the IP board.
Page 81
Does the signal appear at C5064 Check a connection harness. or C5061 of IC5001? Check a LVDS cable ? Replcelcd panel? Please, Call to Samsung Co. LTD. Caution Make sure to disconnect the power before working on the IP board.
Page 82
4. Troubleshooting WAVEFORMS CVBS Output Signal 4-10...
Page 83
Does the Y/C signal appear at Check a connection harness. C5062or C5063 of IC5001? Check a LVDS cable ? Replcelcd panel? Please, Call to Samsung Co. LTD. Caution Make sure to disconnect the power before working on the IP board. 4-11...
Page 84
4. Troubleshooting WAVEFORMS Digital Output Data Analog Signal(Y,C) 4-12...
Page 85
4. Troubleshooting 4-1-7. No Sound Symptom Audio is normal but no picture is displayed on the screen. Check the RF Source Major Check the M-star checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Connect a sound cable.
Page 86
4. Troubleshooting WAVEFORMS The Signal are Inputed to IC1201 The Signal are Inputed to IC1202 4-14...
Page 87
4. Troubleshooting 4-2. Alignments and Adjustments 4-2-1. General Alignment Instuction Usually, a color LCD-TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync. Use the specified test equipment or its equivalent. Correct impedance matching is essential.
Page 88
4. Troubleshooting 4-3. Factory Mode Adjustments 4-3-1 Entering Factory Mode To enter ‘Service Mode’ Press the remote -control keys in this sequence : - If you do not have Factory remote - control INFO MENU MUTE Power on - If you have Factory remote - control PICTURE ON DISPLAY FACTORY...
Page 89
Inch Option /42/46/50/52/57 40 ( LA40A330J1X ) Dimm Type INT/INT_NEG/EXT_POS/EXT_NEG/EXT/ INT ( LA32A330J1X ) EXT ( LA40A330J1X ) 19AM_TN/22AU_TN/22CM_TN/26AM_AG/ 26AU_AG/26CM_NG/32AU_AG/32AU_NG/ 32D C ( LA32A330J1X ) Panel Type 32CM_NG/32CM_AG/37AU_AG/37CP_AG/ 40A C ( LA40A330J1X ) 40AU_AG/40AM_AG Coral/Jade/Tanzanite/Pyrope/Amber Model Option JADE Pyrope_3D/Carnelian/Carnelian_3D Anynet + ON <->...
Page 90
4. Troubleshooting Item Range Option Control WM Calib ON/OFF EDID Protect ON/OFF Edid Type Coral/P450-50HP/P450-42HP L12_1366_768 EDIE Write Failure/Success L12_1366_768 Succes WB Data Reset ON <-> OFF EEPROM Reset Logic Download ON <-> OFF PDP Filter 42” 3D PDP Group P34A_R3d Spread Spectrum ON/OFF...
Page 91
4. Troubleshooting 4-4. White Balance - Calibration 4-4-1 White Balance -Calibration 1. Calibration AV Calibration Comp Calibration PC Calibration HDMI Calibration 4-4-2 Service Adjustment - You must perform Calibration in the Lattice Pattern before adjusting the White Balance. Color Calibration ...
Page 92
4. Troubleshooting Method of Color Calibration (AV) 1) Apply the NTSC Lattice (N0. 3) pattern signal to the AV IN 1 port 2) Press the Source key to switch to “AV1” mode 3) Enter Service mode 4) Select the “Calibration” menu 5) Select the “AV Calibration”...
Page 93
4. Troubleshooting 4-4-3 White Balance - Adjustment (low light) (hight light) Sub Bright Sub Contrast 3. W/B R offset R gain G offset G gain B offset B gain (W/B adjustment Condition refer next page) 4-5. White Ratio (Balance) Adjustment You can adjust the white ratio in factory mode (1:Calibration, 3:White-Balance).
Page 96
4. Troubleshooting 4-6-3 After S/W Upgrade How to Access Service Mode Entering Factory Mode <Power OFF> → <INFO> → <MENU> → <MUTE> → <Power ON> Factory Data Option Table(Service) WB Adjust Information Advanced Menu If you want to enter here, press “0000”. How to Initialize.
6. Wiring Diagram 6-3. Connector Functions Connector Functions Supply main power from SMPS to Main Board. * defective symptom : abnormal Picture CN1001 <-> CNM802 Supply dimming power from SMPS to Main Board. * defective symptom : abnormal Picture CN2101 <-> SPEAKER Connection Main Board and Speaker.