Page 1
HP VS19T SERVICE MANUAL 19” LCD Monitor VS19T THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS RELIABILITY FOR...
HP VS19T 2.LCD Monitor Description The LCD Monitor will contain main board, power board, key board and an audio board which house the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage.
HP VS19T 3.3 Adjust the Picture Control Icons Control Icons Brightness Clock Phase Contrast Power Saver Auto Adjustment Mode Display Image Control Power-On Status Display Color Sleep Timer Custom Color Basic Menu Language Advanced Menu Management Power On Recall OSD Control...
HP VS19T 4. Input/Output Specification 4.1 Input Signal Connector Mnemonic Signal Mnemonic Signal Red Video +5 V +5 V (from PC) Green Video Sync Ground Blue Video None PC Connect detection DDC Data Ground (DDC Return) Horizontal Sync Red GND...
HP VS19T 1) MCU initialize. 2) Is the EEprom blank? 3) Program the EEprom by default values. 4) Get the PWM value of brightness from EEprom. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUTO and SELECT keys pressed? 8) Enter factory mode.
HP VS19T Crystal 24MHz LCD Interface (Y601) (CN503) Scalar IC TSU56AK MTV-512MV (Include ADC, OSD) (U601) (U401) H sync V sync Key Board EEPROM Control AT24C16 (CN602) (U602) Crystal D-Sub 14.318MHz Connector (X401) (CN301) DDC_CLK, DDC_DAT EEPROM M24C02 (U301) 6.3.2 Inverter / Power Board Block Diagram...
Page 16
HP VS19T AC input Bridge Rectifier EMI filter Transformer Dc to Dc Rectifier diodes and Filter StartCircuit: CN902 R909/R910/R931 Feedback Over Circuit Voltage Control IC Protect ON/OFF Transformer MOSFET Resonance Lamp Over ON/OFF Feedback Voltage Control Circuit Control IC...
HP VS19T 9. Maintainability 9.1Equipments and Tools Requirement 1. Multi-meter. 2. Oscilloscope. 3. Pattern Generator. 4. DDC Tool with an IBM Compatible Computer. 5. Alignment Tool. 6. LCD Color Analyzer. 7. Service Manual. 8. User Manual.
HP VS19T 9.2 Trouble Shooting 9.2.1 Main Board 1、No power No power Press power key and look if the picture is normal Please reinsert and make sure the AC of 100-240 is normal Reinsert or check the power section Measure CN201 PIN5/6=12V?
Page 31
HP VS19T No picture (LED is orange) No picture Y601 oscillate waveforms are Key is under control? normal Replace Y601 X401 oscillate waveforms are normal Replace U601 Replace X401 Replace U401 Check if the sync signal from computer is output and video cable...
Page 32
HP VS19T Panel Power Circuit Measure Q204 base is high level? Y601 oscillate waveforms are normal Check Q204 and Q203 are broken Replace Y601 or CN503 solder? Replace U601 Check Correspondent component. Replace U401 Replace PANEL...
HP VS19T 9.2.2 Power Board No Power No power Check AC line volt 110V or 220V Check AC line Check the voltage of C904(+) Check F901, bridge rectified circuit Check start voltage for the pin3 of IC901 Check R912, R916, R918, IC901...
Page 34
HP VS19T No Backlight Check CN903 Pin1/3 =12V Check adapter Check ON/OFF signal Check Interface board Check IC701 PIN6=5V+0.25V Check Q713,Q712, Q702, ZD701 circuit Check IC701 PIN1=5V Check Q707, Q706 circuit Check IC701 PIN 2 triangular wave is normal Check C720, C719, IC201 circuit...
HP VS19T 9.2.3 Keypad Board OSD is unstable or not working Is Keypad board connecting normally Connect Keypad Board Replace Button Switch Is Button Switch normally Replace Keypad Board Is Keypad board normally Check main board...
C. 6500K color: Don’t adjustment,Custom requires. 3. Into factory mode of HP VS19T A. Turn on power, press the down(-) button, pull out the power cord, and then plug the power cord. Then the factory OSD will be at the left top of the panel.
Page 37
HP VS19T B. Adjust sRGB color-temperature 1. Switch the chroma-7120 to sRGB channel. 2. The chroma 7120 will show x = 313 ±20, y = 329 ±20, Y >200 cd/m 3. Switch the chroma 7120 l to RGB MODE ( with press “MODE” button to change ) 4.
(Center). The exact brightness values are confirmed by the checking-regulations of different customers and different models. Ⅱ. Steps of white-balance adjustment for LCD:(Take 19” HP LCD for example) 1. Required instruments: Chroma7120、Chroma2325(BGA265A) 。 2. First connect the instruments together and turn on the LCD power, then warm up for 30 minutes under full white screen mode.
Page 39
HP VS19T d) Test white-balance again after Auto Level. Adjustment with hand is necessary if it is beyond the specs just the same. e) Select 7x00 item to adjust cool color-temperature and select 6x00 to adjust warm color- temperature. It can reach to the best effect through adjusting R/G/B value if it inclines to green or blue.
Page 40
HP VS19T 3.Input the serial number of the product (For instance: AOC LM729 is 13 bits), then press ENTER to start writing 4.Check the indication of DDC-writing program at the end. When you see the picture as the schematic picture above, “Data compare...
Page 41
HP VS19T Instruction:DDC-writing needs 4 files: Barcode.txt (Supply Barcode length and flow number) *.EXE (DDC-writing program) WR.bat (Group order file for cycling utilization of *EXE, and dual-click this file when perform DDC-writing) 4、w.dat The content with 128 bits of DDC...
HP VS19T 13. BOM List T980KS4DKHHPAP Location Part NO. For TPV Description Quantity Unit CBPC980KS4HPAP CONVERSION BOARD KEPC980KD4P KEY BOARD PWPC1942SEH2P POWER BOARD 15G8126 7 MAIN FRAME 23G3178690 6A LOGO 33G4788 PC L STAND-CAP 34G1469APC B BEZEL 44G3918 1 EPS(L)
Page 50
HP VS19T R729 61L0603000 RST SM 0603 JUMP MAX 0R R731 61L0603823 CHIPR 82KOHM +-5% 1/16W R732 61L0603823 CHIPR 82KOHM +-5% 1/16W RP601 61L 125103 8 CHIP AR 8P4R 10KOHM +-5 RP602 61L 125103 8 CHIP AR 8P4R 10KOHM +-5...
Page 51
HP VS19T ZD105 93G 39S 34 T UDZS5.6B ZD106 93G 39S 34 T UDZS5.6B ZD107 93G 39S 34 T UDZS5.6B PWPC1942SEH2P PW1942SEH2SMTP POWER BOARD FOR SMT 11G6049 2 TIE MOUNT(S) 40G 45762420A ID LABEL 1.02 705G 980 57 07 Q901 ASS'Y...
Page 52
HP VS19T L905 73G 253 91 L CHOKE BY LI TA L906 73G 253 91 L CHOKE BY LI TA L909 71G 55 29 FERRITE BEAD NR901 61G 58050 WT NTC 5 OHM 5A PT701 80GL19T 8 DN OZ9RR_TRANS PT702...
Page 57
34G1460 PC B STAND PILLAR 34G1461 PC B BASE Q1G 130 8120 SCREW Q1G 140 8128 SCREW M037 S37G5133 19" HP LCD HINGE ASS'Y 2F0605200 4F0612052 00 METAL WASHER 4F061210M 00 METAL WASHERS12.0*6.03* 4F061210T 00 METAL WASHERS12.0*8.00* 4F061210T 01 METAL WASHERS12.0*4.72*...