Advertisement
Available languages
Available languages
Quick Links
1130615103
INSTALLATION MANUAL
To Qualified Installer in
Installation Work and Service
Wireless receiver kit
(for 4-Way cassette type)
Model: RBC-AXU33UP-UL
Observe the safety precautions described in the Operation Manual of the Wireless
receiver kit, Installation Manual and Operation Manual of the 4-way cassette type air
conditioner (indoor unit), or the Installation Manual supplied with the ceiling panel.
ACCESSORIES
Part Name
Wireless receiver
Remote controller
Remote controller holder
Battery
HOW TO INSTALL THE WIRELESS RECEIVER
Install the Wireless receiver in correct orientation, since the Wireless receiver can be
installed at only one corner as shown in (Fig. 1).
Electrical control box
Indoor unit
refrigerant pipe side
Indoor unit
drain pipe side
1.
Remove the air inlet grille.
2.
Remove the adjust corner cap at the corner
where the Wireless receiver is to be installed.
(Fig. 2)
• Pull the adjust corner cap in the direction
of (1) and slide it in the direction of (2) to
remove it.
• Remove strap from the pin and detach the
adjust corner cap from the ceiling panel.
3.
The insulation pad is packed in the two rectangular holes for ceiling panel wires.
Remove the insulation pad, and pass the wires from the Wireless receiver through
the rectangular holes. (Fig. 3)
4.
Make sure that the black sponge wrapped around the wiring is about 0.8"(20 mm)
out of the rectangular hole on the indoor unit side, and fix it with the Cord clamp
by Screw.
(Fig. 3)
Pass the Wireless receiver lead
wire through the Cord clamp
and fix it with Screw
Remove the insulation pad
from the rectangular hole on
the indoor unit side.
(Fig. 3)
Part Name
Q'ty
Operation Manual
1
Installation Manual
(this manual)
Flat head wood screw
1
Cord clamp
1
Screw
2
"Positioning for installing
a Wireless receiver" is
indicated for guidance
(Fig. 1)
Adjust corner cap
(2)
Ceiling panel
Cord clamp
Screw
Pass the Wireless receiver lead wire
through the hole in the ceiling panel
Pull out the black sponge wrapped
around the wiring about 0.8"(20 mm)
from the rectangular hole.
• Thank you for purchasing Wireless receiver kit for air conditioners.
• Read this manual carefully for correct installation of the Wireless receiver kit before
starting work.
• After the installation is completed, execute a test run to check for normal operation
and explain how to use and maintain the Wireless receiver kit to the customer
according to the Operation Manual.
Ask the customer to keep this manual with the Operation Manual.
CAUTION
• If the black sponge is not properly positioned, water leakage, dew condensation, and
dew condensation on the wiring may occur, so be sure to do so.
5.
Attach the Wireless receiver to the panel. At this time, be careful not to pinch the
Q'ty
wiring. (Fig. 4) If there is a part where the claws of the Wireless receiver part are not
fitted, it may cause water leakage, so push claws A (2 places) and claws B (3 places)
1
firmly and firmly to make sure that the Wireless receiver part does not float. please
confirm.
1
Square hole
2
1
1
Claw A
Insert the claw A (2 places) of the Wireless
receiver into the square holes of the panel
in the direction of the arrow.
CAUTION
• Press the three claws B of the adjust corner cap firmly as far as they will go, and then
check that the adjust corner cap is closely attached.
• Failure to do so may result in water leakage.
HOW TO WIRING THE WIRELESS RECEIVER
1.
Remove the mounting screw A on the electric control box cover and loosen the
screw B. Slide the cover to remove the hook (the electric control box cover remains
(1)
hooked on the hinge).
Hook
(Fig. 2)
2.
Connect the wiring from the Wireless receiver to the connector 9P (CN214: white) on
the P.C.Board of the indoor unit.
Use the cord clamp inside the electrical parts box to process the excess wiring, and
then attach the electric control box cover and air inlet grille.
Cord Clamp
‒ 1 ‒
Claw A
There are claws B here,
so push it in firmly.
Push in the claw B (3 places) on the back side
of the Wireless receiver so that they fit.
(Fig. 4)
Electric control
box cover
Hinge
Screw A
Screw B
Clamping claw
Plug into CN214
EN
Advertisement
Related Manuals for Toshiba Carrier RBC-AXU33UP-UL
Summary of Contents for Toshiba Carrier RBC-AXU33UP-UL
- Page 1 1130615103 INSTALLATION MANUAL • Thank you for purchasing Wireless receiver kit for air conditioners. • Read this manual carefully for correct installation of the Wireless receiver kit before To Qualified Installer in starting work. Installation Work and Service • After the installation is completed, execute a test run to check for normal operation and explain how to use and maintain the Wireless receiver kit to the customer Wireless receiver kit according to the Operation Manual.
- Page 2 SELF-DIAGNOSIS FUNCTION AND MEASURES NOTE • If you do not connect the connector, the Wireless receiver will not operate, so be sure • The following table shows a few examples. For details of indoor unit errors, refer to to connect it securely. the Installation Manual of the indoor unit.
- Page 3 MANUEL D’INSTALLATION • Merci d’avoir acheté ce kit récepteur sans fil pour climatiseurs. • Pour garantir une installation correcte du récepteur sans fil, veuillez lire attentivement À l’installateur qualifié des travaux le présent manuel avant toute intervention. d’installation et d’entretien •...
- Page 4 FONCTIONS ET MESURES D’AUTODIAGNOSTIC REMARQUE • Si vous ne raccordez pas le connecteur, le récepteur sans fil ne fonctionnera pas, • Le tableau suivant montre quelques exemples. Pour en savoir plus sur les erreurs de veillez donc à le raccorder correctement. l’unité...
- Page 5 MANUAL DE INSTALACIÓN • Gracias por comprar el kit inalámbrico receptor para los aires acondicionados. • Lea atentamente este manual para la correcta instalación del receptor inalámbrico Al Instalador cualificado del trabajo antes de ponerlo en funcionamiento. de instalación y servicio •...
- Page 6 MEDIDAS Y FUNCIÓN DE AUTODIAGNÓSTICO NOTA • Si no conecta el conector, la unidad receptora inalámbrica no funcionará, así que • La siguiente tabla muestra algunos ejemplos. Para obtener detalles sobre los errores asegúrese de conectarlo firmemente. de la unidad interior, consulte el Manual de Instalación de la unidad interior. •...