Advertisement
Quick Links
ORDER NO. KMS0508115CE
F5
Streaming Box
BB-S700PDA / BB-S700PDE
(for U.S.A. and Europe)
2005 Panasonic Communications Co., Ltd. All rights reserved.
Unauthorized copying and distribution is a violation of law.
IMPORTANT INFORMATION ABOUT LEAD FREE (PbF), SOLDERING
If lead free solder was used in the manufacture of this product the printed circuit boards will be marked
PbF.
Standard leaded, (Pb), solder can be used as usual on boards without the PbF mark.
1. FOR SERVICE TECHNICIANS
ICs and LSIs are vulnerable to static electricity.
When repairing, the following precautions will help prevent recurring malfunctions.
1. Cover the plastic parts boxes with aluminum foil.
1
Advertisement
Related Manuals for Panasonic BB-S700PDA
Summary of Contents for Panasonic BB-S700PDA
- Page 1 Streaming Box BB-S700PDA / BB-S700PDE (for U.S.A. and Europe) 2005 Panasonic Communications Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. IMPORTANT INFORMATION ABOUT LEAD FREE (PbF), SOLDERING If lead free solder was used in the manufacture of this product the printed circuit boards will be marked PbF.
- Page 2 2. Ground the soldering irons. 3. Use a conductive mat on the worktable. 4. Do not touch IC or LSI pins with bare fingers. 2. CAUTION 2.1. BATTERY CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
- Page 3 4.1. CABLE CONNECTOR PANEL 4.2. PLASMA DISPLAY CONNECTION 4.3. REMOTE CONTROL The remote control of this product uses the remote control receiver of the plasma display. Use within the range of approximately 7 m (275.59 inches) from the remote control receiver of the plasma display.
- Page 4 (see page 4) 5.1.1. Before inserting this product Panasonic "6-Series" plasma displays have slots for installing this product. These are located on the rear panel as shown below.
- Page 5 This product can only be inserted into slot 1 and slot 2 of a plasma display. 1. Turn off the power of the plasma display and any connected equipment. 2. Unplug the AC cord from the mains socket and unplug the connector cable from the plasma display.
- Page 6 * This aforementioned installation method is for a plasma display with three slots (see page 6). For a plasma display with two slots, remove the terminal board inserted into the slots 1 and 2, and install this product. Important - Securely close the fitting that covers the slot. - Take care not to scratch any of the metal parts on the back cover or display sheet when removing or inserting the terminal board in the plasma display.
- Page 7 Important - Use category 5 cable (approx. 100m max.) for the LAN cable. Using an incorrect cable may result in a fault or bad connection. - Use a cable with an stereo mini plug connector for the audio output cable. Using an incorrect cable may cause a fault or bad connection. - You cannot use both the audio output terminal and the audio output on the plasma display at the same time.
- Page 8 6. DISASSEMBLY INSTRUCTIONS Caution: 6.1. HOW TO REMOVE TOP COVER AND BOTTOM COVER...
- Page 9 1. Remove four Screws (A). 2. Remove Top Cover and Bottom Cover from Main Board. 6.2. HOW TO REMOVE HDD (1->2)
- Page 10 1. Remove four Screws (B). 2. Pull connector for HDD. 3. Remove four Screws (C). Note: 1. When putting Screws (C), attach two Screws *(C) of right figure previously in order to decide position. 2. Put in Cable between Main Board and HDD as shows in Figure 1.
- Page 11 1. Remove three Screws (D). 2. Remove Angle from Main Board. 6.4. HOW TO REMOVE FAN 1. Remove five Screws (E). 2. Remove two Screws (F). 3. Pull FAN from Top Cover. Note: When putting a screw, attach correctly in the order of right figure.
- Page 12 *1 Refer to HOW TO REMOVE TOP COVER AND BOTTOM COVER *2 Refer to the Service Manual of Plasma Display. 7.2. CONFIRMING THE REMOTE AND HDD OPERATION...
- Page 14 7.3. BATTERY CHECK...
- Page 15 8. BLOCK DIAGRAM 9. CIRCUIT DESCRIPTION 9.1. HARDWARE FUNCTION OUTLINE - OS: Monta Vista Linux 3.0 (Kernel 2.4.xx) - CPU: PowerPC 405GPr/266MHz - MPEG Decoder: SIGMA DESIGNS EM8476 (Without Macrovision) - Memory: SD-RAM 128MB Flash ROM 512KB for Booting Flash ROM 16MB (upgradable to 32MB)
- Page 16 SRAM 512KB - Video Memory: - LAN: 10BASE-T/100BASE-TX - Storage: HD=20GB approx. (2.5 inches, U-DMA support) - Peripheral: Ir (Infrared remote) - IDE: ATA100/66 Master - Serial: for the internal control (for plasma display control) - Digital Image Output: LVDS - Sound Output: Internal/External (switchable) - DIP Switch:...
- Page 17 The SDRAM is controlled by DRAM controller built in the CPU. Bus width is 32 bits 64M bytes x 2 banks 4 pieces of NT5SV16M16AT-75B or the equivalent should be used. - Flash ROM for Booting Bus width is 16 bits. The MBM29LV400TC or the equivalent should be used.
- Page 18 The MAC is connected to outside PHY (DP83847) through MII bus. - EEPROM The function of the function board (BB-S700PD series board) is described in the EEPROM. It is installed on BB-S700PD series board, and read/write function is controlled by plasma display. The capacity is 16 K bytes.
- Page 19 RS5C372A is used. - DC-DC converter The switching regulator converts the input voltage of 14V into the required voltages of 5 V and 3.3 V. LM2676 is used as the regulator. - Power supply connector for the cooling fan and fan rotation monitoring function The CPU is able to detect the defection of the fan by monitoring its rotation.
- Page 20 - Infrared Remote Interface Infrared Remote Interface receives the signal from the infrared remote. The signal received at the infrared photo acceptance unit is converted to RS-232C (the signal level is TTL) in the sub-processor and led to the CPU through the PLD serial receiver circuit. - Serial Receiver Circuit This serial receiver circuit inside PLD receives the serial data from PIC.
- Page 21 Receiver Control (the interruption during transferring) When the receiver buffer receives the data on the condition that SIF_RES of system register 0 is set to "1", the interruption into CPU occurs. The interruption is released by reading the serial receiver register. Remote Controlling - HDD Interface Interface for the HDD connection...
- Page 22 Stereo sound outputs from MPEG decoder chip. Slot type-Stereo mini jack. When the stereo mini jack is connected, the internal speaker is turned OFF. - Digital Image Output Digital image is output to plasma display. The digital RGB from EM8476 is output after being converted through LVDS transmitter.
- Page 23 A / BBS700PDA / BBS700PDE...
- Page 24 Remote Control Panasonic plasma display (TH-37PWD6, TH-42PWD6, TH-42PHD6 and TH-50PHD6) RS232 serial for plasma display communication DC IN 14V Regular electric supply part Regulator E2PROM (Continuous Feed Block) Remote-Controlled signal DC-DC Regulator +3.3V +2.5V +1.8V DCDC_ON PIC16F630 (sub MPU) Battery backup...