Page 1 ® Satellite L40/L45 Series User’s Guide If you need assistance: ❖ Toshiba’s Support Web site pcsupport.toshiba.com ❖ Toshiba Global Support Centre Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see “If Something Goes Wrong”...
Page 2 TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (“TOSHIBA”), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. YOU AGREE THAT TOSHIBA,...
Page 3 Only Peripherals complying with the FCC Class B limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's ®...
Page 4: Industry Canada Requirement
Contact either: ❖ Toshiba’s Support Web site at pcsupport.toshiba.com. ❖ Or call the Toshiba Global Support Centre: Within the United States at (800) 457-7777 Outside the United States at (949) 859-4273 Industry Canada Requirement This Class B digital apparatus complies with Canadian ICES-003.
Page 5: Telephone Company Procedures
If trouble is experienced with this equipment, for repair or limited warranty information, please contact Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba, or the Toshiba Support Centre within the United States at (800) 457-7777 or Outside the United States at (949) 859-4273.
Page 6 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. Instructions for IC CS-03 Certified Equipment NOTICE: The Industry Canada label identifies certified equipment.
Page 7: Wireless Interoperability
Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❖ The IEEE 802.11 Standard on Wireless LANs (Revision A/B/G), as defined and approved by the Institute of Electrical and Electronics Engineers.
Page 8: Regulatory Information
The radiated output power of the TOSHIBA Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the TOSHIBA Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimized. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Page 9 NOTE The above Caution information applies to products that operate with an 802.11a device. EU Declaration of Conformity TOSHIBA declares that this product conforms to the following Standards: Supplementary *The product complies with the Information: requirements of the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive...
Page 10 VCCI Class B Information Modem Warning Notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Page 11: Device Authorization
2. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions. 3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations. 2. Indication The indication shown below appears on this equipment.
Page 12: Radio Approvals For Wireless Devices
The Name of the radio equipment: refer to the equipment label provided on the computer JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS EQUIPMENT Approval Number: D01-1128JP TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018, 03GZDA0017 The following restrictions apply: ❖ Do not disassemble or modify the device. ❖...
Page 13 Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries België/ For private usage outside buildings across public grounds over less than Belgique: 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m.
Page 14 802.11a (5 GHz) Australia Austria Belgium Canada Denmark Finland France Germany Greece Ireland Italy Liechtenstein Luxembourg Netherlands New Zealand Norway Portugal Sweden Switzerland Turbo Mode (5 GHz) Canada Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries European Community 5150-5250 MHz 5250-5350 MHz...
Page 15 ❖ This device must not be operated in ad-hoc mode using channels in the 5 GHz bands in the European Community. Ad-hoc mode provides a direct communication between two client devices without a Wireless LAN Access Point. ❖ This device must be used with Access Points that have employed and activated a radar detection feature required for European Community operation in the 5 GHz bands.
Page 16 802.11a (5 GHz) Australia Austria Belgium Canada Denmark Finland France Germany Greece Ireland Italy Liechtenstein Luxembourg Netherlands New Zealand Norway Portugal Sweden Switzerland Turbo Mode (5 GHz) Canada ® Approved Countries/Regions for use for the Intel PRO/ Wireless LAN 2100 3B Mini PCI Adapter This equipment is approved to the radio standard by the countries/regions in the following table.
Page 17: Wireless Lan Card
Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Page 18: Bluetooth Wireless Technology Interoperability
Always use Bluetooth cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA computer product support on Web site http://www.toshiba-europe.com/computers/tnt/ bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for...
Page 19 Approved Countries/Regions for use (Bluetooth wireless technology) ® Bluetooth Card from Toshiba equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Argentina...
Page 20: Bluetooth Wireless Technology And Your Health
The radiated output power of the Bluetooth Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.
Page 21 2. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions. 3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations.
Page 22 This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-15-1048 Direct Dial: 03-3457-4850...
Page 23 (Sample shown below. Location of the label and manufacturing information may vary.) Copyright This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
Page 24 EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING. TOSHIBA ASSUMES NO LIABILITY FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR OMISSIONS CONTAINED HEREIN OR FOR DISCREPANCIES BETWEEN THE PRODUCT AND THE MANUAL.
Page 25 Card is a trademark of Fuji Photo Film, Co., Ltd. Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Toshiba is under license. Other trademarks and trade names are those of their respective owners.
Page 26: Table Of Contents
Keeping yourself comfortable ......38 Precautions............38 Important information on your computer’s cooling fan...............39 Setting up your computer ........40 Setting up your software........40 Registering your computer with Toshiba ....41 Adding optional external devices......41 Connecting to a power source ........42 Charging the main battery........44...
Page 27 Contents Using the computer for the first time ......45 Opening the display panel .........45 Your computer’s features and specifications ..46 Turning on the power ........46 Adding memory (optional) ........47 Installing a memory module ......48 Removing a memory module......53 Checking total memory ........55 Hard Drive Recovery Utilities ........56 Creating Recovery CDs/DVDs ......57 Hard Disk Drive Recovery options ....58...
Page 28 Removing a disc with the computer on.....96 Removing a disc with the computer off ....97 Caring for CD or DVD discs ......97 Toshiba’s online resources ........97 Chapter 3: Mobile Computing........... 98 Toshiba’s energy-saver design........98 Running the computer on battery power ....98...
Page 29 Contents Battery Notice ...........99 Power management ........100 Using additional batteries .......100 Charging batteries..........100 Charging the main battery.......101 Charging the RTC battery........101 Monitoring main battery power......102 Determining remaining battery power.....104 What to do when the main battery runs low ...104 Setting battery notifications ......105 Conserving battery power ......105 Power Plans............106 Using a hot key to set the Power Plan.....107...
Page 30 Inserting an ExpressCard™ ......128 Removing an ExpressCard™ ......129 Using the Bridge Media Adapter Slot ....130 Inserting memory media.........130 Removing memory media.......131 Chapter 5: Utilities..............132 TOSHIBA Assist ............133 Connect............134 Optimize............135 TOSHIBA Application Installer.......136 Mouse Utility ............137 CD/DVD Drive Acoustic Silencer ......138 TOSHIBA Accessibility ..........139...
Page 31 Data and system configuration backup in the ® Windows operating system.....170 If you need further assistance.......174 Before you contact Toshiba ......174 Contacting Toshiba .........175 Other Toshiba Internet Web sites......175 Toshiba’s worldwide offices........176 Appendix A: Hot Keys.............. 178 Hot Keys ...............178 Hot key functions ..........179...
Page 32 Contents Disabling or enabling the TouchPad ....183 Keyboard hot key functions ......183 Appendix B: Power Cord/Cable Connectors......184 Glossary..................185 Index..................199...
Page 33: Introduction
Introduction Welcome to the world of powerful, portable, multimedia computing. With your Toshiba notebook computer, your work and entertainment can accompany you wherever you go. NOTE This notebook is compatible with European Union Directive 2002/95/EC, Restriction of the use of certain Hazardous Substances in electrical and electronic equipment (RoHS), which restricts use of lead, cadmium, mercury, hexavalent chromium, PBB, and PBDE.
Page 34: This Guide
Toshiba’ s Web site at pcsupport.toshiba.com. While Toshiba has made every effort at the time of publication to ensure the accuracy of the information provided herein, product specifications, configurations, prices, system/component/options availability are all subject to change without notice.
Page 35: Safety Icons
Introduction Safety icons Safety icons This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Page 36: Other Documentation
To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com. If you have a problem or need to contact Toshiba, see “If Something Goes Wrong” on page...
Page 37: Chapter 1: Getting Started
Chapter 1 Getting Started This chapter provides tips for working comfortably, summarizes how to connect components, and explains what to do the first time you use your notebook computer. Selecting a place to work Your computer is portable and designed to be used in a variety of circumstances and locations.
Page 38: Keeping Yourself Comfortable
Extreme heat, cold, or humidity. ❖ Liquids and corrosive chemicals. Keeping yourself comfortable The Toshiba Instruction Manual for Safety and Comfort, that shipped with your computer, contains helpful information for setting up your work environment and tips for working comfortably throughout the day.
Page 39: Important Information On Your Computer's Cooling Fan
Getting Started Selecting a place to work ❖ Never turn off the computer if a drive light indicates a drive is active. Turning off the computer while it is reading from or writing to a disk/disc or flash media may damage the disk/disc or flash media, the drive, or both.
Page 40: Setting Up Your Computer
Getting Started Setting up your computer Setting up your computer TECHNICAL NOTE: You must complete all setup steps up to and including “Setting up your software” on page 40 before adding external or internal components to your computer. These components include, but are not limited to, a mouse, keyboard, printer, memory, and PC Cards.
Page 41: Registering Your Computer With Toshiba
If you decide not to register at that time, you can either double-click the Toshiba Registration icon on your desktop or go to the Toshiba Web site at www.register.toshiba.com at a later time. Failure to complete Product Registration will not diminish Customer rights under the Toshiba limited Warranty.
Page 42: Connecting To A Power Source
TOSHIBA Battery Charger (that may have been provided with your computer), or use AC adaptors and battery chargers specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the computer possibly resulting in serious injury.
Page 43 Getting Started Connecting to a power source To connect AC power to the computer: Connect the power cord/cable to the AC adaptor. (Sample Illustration) Connecting the power cord/cable to the AC adaptor Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
Page 44: Charging The Main Battery
Getting Started Charging the main battery Never attempt to connect or disconnect a power plug with wet hands. Failure to follow this instruction could result in an electric shock, possibly resulting in serious injury. The computer’s main battery light gives you an indication of the main battery’s current charge: ❖...
Page 45: Using The Computer For The First Time
Getting Started Using the computer for the first time Using the computer for the first time The computer is now ready for you to turn it on and begin using it. Opening the display panel Facing the front of the computer, locate the center of the display panel.
Page 46: Your Computer's Features And Specifications
Getting Started Using the computer for the first time Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precision technology.
Page 47: Adding Memory (Optional)
You may want to increase the computer’s memory if you use complex software or process large amounts of data. NOTE Before adding external devices or memory, Toshiba recommends setting up your software. See “Setting up your software” on page...
Page 48: Installing A Memory Module
Getting Started Adding memory (optional) Installing a memory module Memory modules can be installed in the memory module slots on the base of the computer. You will need a small Phillips screwdriver for this procedure. If the computer has been running recently, the memory module may be hot.
Page 49 Getting Started Adding memory (optional) If the computer is on, begin at step 1; otherwise, skip to step 3. Click Start, and then click the arrow next to the lock button in the lower-right corner of the Start menu. The Shut Down menu appears. Arrow Start Shut Down Menu...
Page 50 Getting Started Adding memory (optional) Using a small Phillips screwdriver, loosen the captive screws that secure the memory module slot cover. Front of computer (Sample Illustration) Removing the memory module slot cover Remove the memory module slot cover. Place the screws and the cover in a safe place so that you can retrieve them later.
Page 51 Getting Started Adding memory (optional) NOTE If your system has the memory modules stacked on top of one another, you must remove the top module first before removing/installing the bottom module. NOTE For this model Slot A is the bottom slot. Slot B is the top slot.If only one memory module is to be installed, it must be installed in slot A.
Page 52 Getting Started Adding memory (optional) Once the module’s connector is fully inserted into the socket, press downward on the top edge of the module to seat the module into the latches at the sides of the socket. These latches should “snap” into place securely with the corresponding cutouts in the side of the module.
Page 53: Removing A Memory Module
Getting Started Adding memory (optional) Re-insert the main battery. For more information on inserting the main battery, see “Inserting a charged battery” on page 110. Turn the computer right side up. Reconnect the cables. Restart the computer. TECHNICAL NOTE: You must have at least one memory module installed for the computer to work.
Page 54 Getting Started Adding memory (optional) NOTE The following screen may appear when you turn on the power: Memory modules ® If “Start Windows Normally” is highlighted, then press Enter If one of the Safe Mode options is highlighted, it is best to press to go into Safe Mode, then shut down and restart the system, at Enter ®...
Page 55: Checking Total Memory
Getting Started Adding memory (optional) Gently lift the memory module to a 30-degree angle and slide it out of the slot. Slot A Slot B (Sample Illustration) Removing the memory module Replace the memory module slot cover and secure it using the screws.
Page 56: Hard Drive Recovery Utilities
Getting Started Hard Drive Recovery Utilities If the computer does not recognize the memory configuration, turn off the computer and remove the memory module slot cover (complete steps “Installing a memory module” on page 48), and then check that the module is inserted completely into the socket and lined up squarely with the socket latches.
Page 57: Creating Recovery Cds/Dvds
The system will prompt you to insert the appropriate number of blank CDs or DVDs to copy the Hard Drive Recovery Utilities. If your optical disc drive is not writable, contact Toshiba Customer Support to obtain the Recovery media for your system.
Page 58: Hard Disk Drive Recovery Options
Getting Started Hard Drive Recovery Utilities Select the items you want to copy by clicking the check box next to the item’s Name—recovery files, applications (original bundled drivers and applications), or both the recovery files and applications. Click Create. Insert the first blank CD or DVD into your writable optical drive when prompted.
Page 59 (zero) key on your keyboard while powering on the computer. When the computer powers on, the Toshiba Recovery Wizard screen displays. (Sample Image) Toshiba Recovery Wizard screen Select one of the options, and then click Next. The options are: ❖...
Page 60 Getting Started Hard Drive Recovery Utilities On the Toshiba Recovery Wizard screen, select Recovery of Factory Default Software, and then click Next. The Recovery of Factory Default Software screen appears. (Sample Image) Recovery of Factory Default Software screen Select Recover to out-of-box-state, and then click Next.
Page 61 The Recovery Wizard allows you to delete all data and partitions from the hard disk. To delete the data and partitions from your hard disk: On the Toshiba Recovery Wizard screen, select Erase the hard disk, and then click Next. The next screen lists the two methods you can choose: ❖...
Page 62 To recover only your C: drive: On the Toshiba Recovery Wizard Screen, select Recovery of Factory Default Software, and then click Next. Select Recover without changing the hard drive partitions.
Page 63: Hard Disk Drive Recovery Using The Recovery Media
When the initial screen displays, press The boot menu appears. Using the arrow keys, select the CD/DVD option and press Enter . The system will boot up to the Toshiba Recovery Wizard screen. Please refer to “Hard Disk Drive Recovery options” on page 58, to explain the available recovery options.
Page 64: Installing Drivers And Applications
Installing drivers and applications (Available on certain models) The TOSHIBA Application Installer (available on certain models) allows you to reinstall the drivers and applications that were originally bundled with your computer. To reinstall drivers and applications: Double-click the TOSHIBA Application Installer icon on the ®...
Page 65: Scrolling With The Touchpad
Getting Started Using external display devices NOTE Because the TouchPad is much smaller than the display screen, moving your cursor across the screen often means having to move your finger several times across the TouchPad in the preferred direction. Once you have positioned your cursor, you can click it into place by either double-tapping the TouchPad or clicking the control buttons.
Page 66: Directing The Display Output When You Turn On The Computer
Getting Started Using external display devices Connecting an external monitor or projector You can easily attach an external monitor or projector to your computer if you need a larger screen. To do this: Connect the monitor’s video cable to the RGB (monitor) port on the side of the computer.
Page 67: Adjusting The Quality Of The External Display
Getting Started Using an external keyboard Release the key. Adjusting the quality of the external display To obtain the best picture quality from your television (or other video display device), you may need to adjust the video settings. See the video device documentation for additional configuration steps.
Page 68: Setting Up A Printer
Getting Started Connecting a printer If your printer supports Plug and Play, your computer may automatically recognize the printer; the printer is then ready for use. Refer to your printer documentation for further instructions. TECHNICAL NOTE: To determine if your printer supports Plug and Play, check its documentation.
Page 69: Connecting An Optional External Diskette Drive
Getting Started Connecting an optional external diskette drive Connecting an optional external diskette drive Some operations, such as creating a password service diskette, require a diskette drive designed for use with 3.5-inch diskettes. (Sample Illustration) Optional external USB diskette drive To connect an optional external USB diskette drive, connect the cable to one of the computer’s USB ports.
Page 70: Options For Turning Off The Computer
Getting Started Turning off the computer Options for turning off the computer Depending on the operating system installed, you have more than one option available for turning off the computer: Shut Down, Hibernate, and Sleep. Each option has its advantages. ❖...
Page 71 Getting Started Turning off the computer For information on how to use and configure Hibernation mode see “Using and configuring Hibernation mode” on page Sleep mode The Sleep command places the computer into a power-saving mode. Sleep saves the current state of the computer to memory so that, when you restart the computer, you can continue working from where you left off.
Page 72: Using The Shut Down Command
Getting Started Turning off the computer Using the Shut Down command The Shut down command completely shuts down the computer without saving your work or the current state of the computer. This command closes all open programs, shuts down the operating system, and then turns off your computer.
Page 73 Getting Started Turning off the computer Click Change advanced power settings. The Advanced settings tab of the Power Options window appears. (Sample Image) Advanced settings tab of Power Options screen Click Power buttons and lid to display the actions that you can configure.
Page 74: Using And Configuring Hibernation Mode
Getting Started Turning off the computer Once the computer is configured, you can turn it off by either pressing the power button or closing the display panel, depending on the options set. Restarting your computer To start the computer up again, press the power button until the on/off light glows green.
Page 75 Getting Started Turning off the computer Click Start, Control Panel, System and Maintenance, and then Power Options. The Power Options window appears. Click Change plan settings under the power plan to be customized. The Edit Plan Settings window appears. Click Change advanced power settings. The Advanced settings tab of the Power Options window appears.
Page 76: Using And Configuring Sleep Mode
Getting Started Turning off the computer ❖ Power button action Set this option to Hibernate if you want the computer to go into Hibernation mode when you press the power button. ❖ Start menu power button Set this option to Hibernate if you want the computer to go into Hibernation mode when you click the power button in the Start menu.
Page 77 Getting Started Turning off the computer Click Sleep. The computer saves the status of all open programs and files to the memory, turns off the display, and enters into a low-power mode. The on/off light blinks amber indicating the computer is in Sleep mode.
Page 78 Getting Started Turning off the computer Click Change advanced power settings. The Advanced settings tab of the Power Options window appears. (Sample Image) Advanced settings tab of Power Options screen Click Power buttons and lid to display the actions that you can configure.
Page 79: Closing The Display Panel
Getting Started Customizing your computer’s settings Once the computer is configured, you can place it into Sleep mode by either pressing the power button or closing the display panel, depending on the Sleep options set. Starting again from Sleep mode To start up the computer from Sleep mode, press the power button until the on/off light glows green.
Page 80: Moving The Computer
You may want to secure your computer to a heavy object such as your desk. The easiest way to do this is to purchase an optional computer lock cable. For more information on purchasing a cable lock, visit accessories.toshiba.com. (Sample Illustration) Computer lock cable To secure the computer: Wrap the cable through or around some part of a heavy object.
Page 81: Chapter 2: Learning The Basics
Chapter 2 Learning the Basics This chapter gives some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work stays in the computer’s temporary memory until you save it to the disk. If the network you are using goes down and you must restart your computer to reconnect, or your battery runs out of charge while you are working, you will lose all work since you last saved.
Page 82 Learning the Basics Computing tips ❖ Back up your files to disks (or other removable media) on a regular basis. Label the backup copies clearly and store them in a safe place. It is easy to put off backing up because it takes time. However, if your hard disk suddenly fails, you will lose all the data on it unless you have a separate backup copy.
Page 83: Using The Keyboard
Learning the Basics Using the keyboard Using the keyboard Your computer’s keyboard contains character keys, control keys, ® function keys, and special Windows keys. (Sample Illustration) Keyboard Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖...
Page 84: Ctrl, Fn, And Alt Keys
Learning the Basics Using the keyboard Ctrl, Fn, and Alt keys (Sample Illustration) Ctrl, Fn, and Alt keys Ctrl , and keys do different things depending on the program you are using. For more information, see your program documentation. Function keys The function keys (not to be confused with the key) are the 12 keys at the top of the keyboard.
Page 85: Overlay Keys
Learning the Basics Using the keyboard Overlay keys The keys with gray numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would using the 10-key keypad on a desktop computer’s keyboard.
Page 86: Starting A Program
Learning the Basics Starting a program Starting a program The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. To find ® the file, use the Start menu or Windows Explorer.
Page 87: Starting A Program From Windows
Learning the Basics Starting a program ® Starting a program from Windows Explorer If a program is not listed in the All Programs menu, you can start it ® ® from Windows Explorer. Windows Explorer gives you a view of your computer’s contents as a hierarchy or “tree.”...
Page 88: Starting A Program Using The Start Search Field
Learning the Basics Saving your work Starting a program using the Start Search field This example uses the Start menu’s Start Search field to start WordPad: Click Start to display the Start menu. The Start Search field appears at the bottom of the Start menu. Start Search field...
Page 89 Learning the Basics Saving your work Saving files ® In your Windows -based application, click File, and then Save. Click Browse folders. If you are working with a document that already has a file name, this is all you need to do. If you created a new document, your program displays a Save As dialog box.
Page 90: Printing Your Work
Learning the Basics Printing your work Using a file extension Most programs assign an extension to the file name that identifies the file as being created in the program with a particular format. For ® example, Microsoft Word saves files with a .doc extension. Any ®...
Page 91: Backing Up Your Work
Learning the Basics Backing up your work Specify the print parameters. For example, the range of pages and number of copies to print. Click Print. Backing up your work Back up all the files you create in case something happens to your computer.
Page 92: Optical Drive Components
Learning the Basics Using the optical drive TECHNICAL NOTE: Your optical drive is set to play region 1 (North America) DVD-ROMs. If you play a DVD disc from another region, the drive will automatically change to play in the format of the other region.
Page 93: Inserting An Optical Disc
Learning the Basics Using the optical drive Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. Inserting an optical disc To insert an optical disc into the drive: Make sure the computer is turned on.
Page 94: Playing An Audio Cd
If you insert the disc incorrectly, it may jam the drive. If this happens, contact Toshiba support for assistance. Push the disc tray in by pressing gently on the center of the tray until it clicks into place.
Page 95: Playing Optical Media
Learning the Basics Using the optical drive ® NOTE When using Windows Media Player, your system may not be able to activate Sleep or Hibernation modes. To prevent this from ® occurring, close Windows Media Player before you select Sleep or Hibernation mode.
Page 96: Creating A Cd/Dvd
Due to manufacturing and quality variations in third party optical media (e.g., CD or DVD) or optical media players/recorders, in certain cases, your Toshiba optical drive may not record on certain optical media that bear the applicable logo, or play back optical media recorded by other computers or optical media recorders.
Page 97: Removing A Disc With The Computer Off
Toshiba’s online resources Toshiba maintains a number of online sites to which you can connect. These sites provide information about Toshiba products, give help with technical questions and keep you up to date with future upgrades.
Page 98: Chapter 3: Mobile Computing
Mobile Computing This chapter covers all aspects of using your computer while traveling. Toshiba’s energy-saver design Your computer enters a low-power suspension mode when it is not being used, thereby conserving energy and saving money in the process. It has a number of other features that enhance its energy efficiency.
Page 99: Battery Notice
This is normal for all batteries. To purchase a new battery pack, see the accessories information that shipped with your computer or visit the Toshiba Web site at accessories.toshiba.com. Use only batteries designed to work with your Toshiba notebook computer.
Page 100: Power Management
Never leave batteries in the battery charger for more than a week at a time. Doing so may reduce the potential charge of the battery. Always use the battery charger specified by Toshiba. You can order a Toshiba battery charger from Toshiba’s Web site at accessories.toshiba.com.
Page 101: Charging The Main Battery
Mobile Computing Charging batteries Charging the main battery To charge the main battery while it is in your computer, plug the computer into a live electrical outlet. The battery charges whether the computer is on or off. TECHNICAL NOTE: The recharging of the battery cannot occur when your computer is using all of the power provided by the AC adaptor to run applications, features, and devices.
Page 102: Monitoring Main Battery Power
Mobile Computing Monitoring main battery power NOTE The above error message may vary by computer model. The RTC battery does not charge while the computer is turned off even when the AC adaptor is charging the computer. The RTC battery charges when the computer is powered on.
Page 103 Mobile Computing Monitoring main battery power NOTE Battery life and charge time may vary, depending upon power management settings, applications and features used. ❖ Flashes amber when the main battery charge is low and it is time to recharge the main battery or plug in the AC adaptor. HINT: Be careful not to confuse the battery light ( ), with the on/off light (...
Page 104: Determining Remaining Battery Power
Mobile Computing Monitoring main battery power Determining remaining battery power Wait at least 16 seconds after turning on the computer before trying NOTE to monitor the remaining battery power. The computer needs this time to check the battery’s remaining capacity and perform its calculations.
Page 105: Setting Battery Notifications
Mobile Computing Monitoring main battery power Setting battery notifications You can set two notifications. Each notification can be set to alert you when a specified percentage of remaining battery power has been reached. You can also set the computer to enter Sleep mode or Hibernation mode or to completely power down when the notification goes off.
Page 106: Power Plans
Mobile Computing Monitoring main battery power ❖ How much you use the hard disk, optical drive, diskette drives, or other optional devices ❖ Where you are working, since operating time decreases at low temperatures There are various ways in which you can conserve power and extend the operating time of your battery: ❖...
Page 107: Using A Hot Key To Set The Power Plan
Mobile Computing Monitoring main battery power Select an appropriate plan for your work environment or create your own custom plan. Click Create a Power Plan to set up a new plan. To edit a plan or to edit advanced settings, continue to the following NOTE steps.
Page 108: Changing The Main Battery
Mobile Computing Changing the main battery While continuing to press , press until you select the desired Power Plan. The Power Plan options are: Balanced, and High Performance. Release the key. You are now in the selected mode. Changing the main battery When your main battery has run out of power, you have two options: plug in the AC adaptor or install a charged main battery.
Page 109 Mobile Computing Changing the main battery Slide the battery release lock to the unlocked position. (Sample Illustration) Unlocking the battery release lock Slide the battery release latch to release the battery. Pull the discharged battery out of the computer. (Sample Illustration) Removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately.
Page 110: Inserting A Charged Battery
Mobile Computing Changing the main battery Inserting a charged battery To insert a battery: Wipe the terminals of the charged battery with a clean cloth to ensure a good connection. Insert the charged battery into the slot until the latch clicks. The battery pack has been designed so that you cannot install it with reverse polarity.
Page 111: Taking Care Of Your Battery
If a battery is leaking or damaged, replace it immediately. Use protective gloves when handling a damaged battery. ❖ To replace the main battery, use an identical battery that you can purchase through the Toshiba Web site at accessories.toshiba.com. ❖ A reverse polarity condition should be avoided with all batteries.
Page 112: Maintaining Your Battery
Mobile Computing Taking care of your battery Maintaining your battery Fully discharging your battery pack will allow better accuracy of the battery meter. To fully discharge your battery pack: ❖ Periodically, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges.
Page 113: Disposing Of Used Batteries
If you cannot find the information you need elsewhere, call Toshiba at: (800) 457-7777. Toshiba is dedicated to preserving the environment by sponsoring Call2Recycle™, a program of the Rechargeable Battery Recycling...
Page 114: Traveling Tips
❖ Always travel with the computer in a carrying case. Toshiba offers a choice of carrying cases for the computer. They all provide plenty of extra space for manuals, power cords, and compact discs.
Page 115: Chapter 4: Exploring Your Computer's Features
Chapter 4 Exploring Your Computer’s Features In this chapter, you will explore some of the special features of your notebook computer. Exploring the desktop The desktop is the launching pad for everything you can do in the ® Windows operating system. You use its features to start programs, find documents, set up system components, and perform most other computing tasks.
Page 116: Finding Your Way Around The Desktop
Exploring Your Computer’s Features Exploring the desktop Finding your way around the desktop Your computer’s desktop includes several standard features: icons, Start button, Taskbar, Notification Area, and background pattern. Icons Start button Taskbar Notification Area ® (Sample Image) Windows operating system desktop Icons An icon represents a folder, file, or program that can be quickly activated by double-clicking the icon.
Page 117 Exploring Your Computer’s Features Exploring the desktop Your desktop may contain other icons depending on your ® configuration. See Windows online Help for more specific information on each icon and how to use it. Start button You use the Start button to: ❖...
Page 118: Setting Up For Communications
Exploring Your Computer’s Features Setting up for communications Setting up for communications To connect to the Internet, use an online service, or communicate across the telephone lines with another computer, you need: ❖ A browser or communications program ❖ An Internet Service Provider (ISP) or online service if you plan to use the Internet ❖...
Page 119: Connecting A Modem To A Telephone Line
Send a fax directly from your computer For more detailed information regarding your computer’s modem, visit Toshiba’s Web site at accessories.toshiba.com. Before you can communicate using the modem, you need to connect it to a telephone line. Your computer’s built-in modem port provides an RJ-11 jack, allowing you to connect the modem to a standard voice-grade telephone line.
Page 120: Connecting Your Computer To A Network
Exploring Your Computer’s Features Setting up for communications Connect the other end to the RJ-11 wall jack. (Sample Illustration) Connecting to a wall jack NOTE Connect the built-in modem only to ordinary analog phone lines. Never connect the built-in modem to a digital line (ISDN). Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX).
Page 121 Exploring Your Computer’s Features Setting up for communications Setting up the connection To set up an office connection, consult your network administrator for network settings and additional considerations. To set up a dial-up connection, use the Connect to the Internet Wizard: Click Start, Control Panel, Network and Internet, and then Connect to the Internet.
Page 122: An Overview Of Using The Internet
Exploring Your Computer’s Features An overview of using the Internet Using Wireless LAN connectivity (Available on certain models) NOTE Wireless connectivity and some features may require you to purchase additional software, external hardware or services. Availability of public wireless LAN access points may be limited. Your system may come with an optional wireless LAN module.
Page 123: The World Wide Web
Exploring Your Computer’s Features An overview of using the Internet The World Wide Web The World Wide Web (or “Web”) is a subset of the Internet—a collection of interlinked documents (located on computers connected to the Internet) that work together using a specific Internet protocol called Hypertext Transfer Protocol (HTTP).
Page 124: Surfing The Internet
Exploring Your Computer’s Features An overview of using the Internet Surfing the Internet Once connected to the Internet, the Web browser displays a home page, for example, your ISP’s home page on the Internet or your company’s Web site home page. To visit a desired Web site, type in the Web address.
Page 125: Uploading To, And Downloading Files From, The Internet
Exploring Your Computer’s Features Exploring audio features Uploading to, and downloading files from, the Internet Transferring files from one computer to another is termed uploading (transferring data from your computer to a site on the Web), or downloading (transferring data from a site on the Web to your computer).
Page 126: Using External Speakers Or Headphones
Exploring Your Computer’s Features Using PC Cards Using external speakers or headphones Your computer is equipped with a full stereo sound system with internal speakers. Instead of using the internal speakers, you can connect headphones or a pair of external stereo speakers. Before putting on headphones to listen, turn the volume down.
Page 127: Inserting A Pc Card
Exploring Your Computer’s Features Using PC Cards Inserting a PC Card Before you insert a PC Card, refer to the documentation that comes with the card to see if you need to do anything before you insert it. To insert a PC Card: Locate the PC Card slot on the side of the computer.
Page 128: Setting Up A Pc Card For Your Computer
Exploring Your Computer’s Features Using an ExpressCard™ Press the PC Card eject button once to pop it out slightly, and push it in to remove the PC Card. The PC Card ejects slightly from the slot. Grasp the edges of the PC Card and slide it out of the slot. (Sample Illustration) Removing a PC Card Setting up a PC Card for your computer Some PC Cards are ready to use as soon as you install them.
Page 129: Removing An Expresscard
Exploring Your Computer’s Features Using an ExpressCard™ Insert the ExpressCard. (Sample Illustration) Inserting an ExpressCard When the card is almost all the way into the slot, push firmly but gently to ensure a firm connection with the computer. Do not force the card into position. ™...
Page 130: Using The Bridge Media Adapter Slot
PDAs, digital cameras, digital video camcorders, etc. The Bridge Media Adapter slot may also support other types of media. For a complete list of supported media, visit Toshiba’s Web site at accessories.toshiba.com. NOTE Do not use the Copy Disk function for this type of media.
Page 131: Removing Memory Media
Exploring Your Computer’s Features Using the Bridge Media Adapter Slot Removing memory media Prepare the media for removal by clicking the Safely Remove Hardware icon in the Notification Area and then selecting the card or device you want to remove. If the system is unable to prepare the media for safe removal, a message will tell you to try again later.
Page 132: Chapter 5: Utilities
Together, these allow you to ascertain certain system details, set additional options, or change default options. These utilities are described in this chapter. ❖ TOSHIBA Assist ❖ TOSHIBA Application Installer ❖ Mouse Utility ❖ CD/DVD Drive Acoustic Silencer ❖ TOSHIBA Accessibility ❖...
Page 133: Toshiba Assist
Utilities TOSHIBA Assist TOSHIBA Assist The TOSHIBA Assist provides quick access to computer functions and allows you to customize a range of computer settings. To access TOSHIBA Assist, do one of the following: ❖ Double-click the TOSHIBA Assist shortcut icon on the desktop.
Page 134: Connect
Utilities TOSHIBA Assist Connect The features available in this category are: ❖ ® ConfigFree Connectivity Doctor (Sample Image) TOSHIBA Assist window – Connect tab...
Page 135: Optimize
Utilities TOSHIBA Assist Optimize The features available in this category are: ❖ Mouse Utility ❖ CD/DVD Drive Acoustic Silencer (Sample Image) TOSHIBA Assist window – Optimize tab...
Page 136: Toshiba Application Installer
Utilities TOSHIBA Application Installer TOSHIBA Application Installer (Available on certain models) The TOSHIBA Application Installer allows you to reinstall the drivers and applications that were originally bundled with your computer. To reinstall drivers and applications: Double-click the TOSHIBA Application Installer icon on the ®...
Page 137: Mouse Utility
To access the Mouse utility: Click Start, Control Panel, and then Mouse under Hardware and Sound, or click the Mouse icon in the Optimize tab of TOSHIBA Assist. The Mouse Properties screen appears. (Sample Image) Mouse Properties screen The settings you can change are divided into these categories: ❖...
Page 138: Cd/Dvd Drive Acoustic Silencer
To access the utility: Double-click the icon in the Notification Area, or click the CD/DVD Drive Acoustic Silencer icon in the Optimize tab of TOSHIBA Assist. The CD/DVD Drive Acoustic Silencer screen appears. Click Silence Mode to make the drive run more slowly and quietly for listening to music or audio files on a CD.
Page 139: Toshiba Accessibility
Utilities TOSHIBA Accessibility TOSHIBA Accessibility The TOSHIBA Accessibility utility allows you to use the key to create a hot key combination with one of the function keys without pressing the two keys simultaneously as is usually required. Using Accessibility lets you make the...
Page 140: Configfree
Double-click the ConfigFree icon in the Notification Area. ❖ Press the TOSHIBA Assist button (if applicable to your system) to open the TOSHIBA Assist, and then click the ConfigFree icon. ❖ Click the ConfigFree icon in the Notification Area, and...
Page 141: Configfree® Utilities
Utilities ConfigFree® NOTE If your computer is not connected to a network, the ConfigFree icon in the Notification Area is displayed with an “X.” ® ConfigFree Utilities Connectivity Doctor The Connectivity Doctor lets you analyze your network connections and fix network connection problems. Using Connectivity Doctor, you can view detailed network information by simply moving the mouse pointer.
Page 142 Utilities ConfigFree® Profile Settings The Profile Settings utility lets you save network settings in “profiles.” ConfigFree profiles are useful for easily switching network settings and devices.You can switch network settings simply by selecting the profile with the desired settings. If you visit a client company occasionally, for example, you can set up a profile to match that environment and connect to the network.
Page 143 Utilities ConfigFree® Click Open Settings. The ConfigFree Profile Settings window appears. (Sample Image) ConfigFree Profile Settings window Click Add to start the Create Profile Wizard.
Page 144: Chapter 6: If Something Goes Wrong
This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter.
Page 145: Problems When You Turn On The Computer
If Something Goes Wrong Problems when you turn on the computer Click the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list. Select the program you want to close, then click End Task. Closing the failed program should allow you to continue working.
Page 146 If Something Goes Wrong Problems when you turn on the computer The computer starts but when you press a key nothing happens. Verify that the active program accepts text input. Try clicking your mouse on an area where you can type text and try typing again. Your computer may be in Sleep mode and have a software or resource conflict.
Page 147: The Windows Operating System Is Not Working
If Something Goes Wrong ® The Windows operating system is not working If you are running on battery power, it is recommended that you do not leave the computer in Sleep mode for long periods of time. To charge the battery, leave the computer plugged into a live wall outlet for several hours.
Page 148: Internet Problems
If Something Goes Wrong ® The Windows operating system is not working ® Press when your computer starts and before Windows starts loading. ® The Windows Advanced Boot Options menu displays these options: ❖ Safe Mode ❖ Safe Mode with Networking ❖...
Page 149: The Windows Operating System Can Help You
Click one of the options listed in the window and then follow the on-screen instructions. You can connect to Support Online by clicking Microsoft Customer Support or by going to Toshiba support at pcsupport.toshiba.com. Resolving a hardware conflict If you receive an error message telling you there is a device driver ®...
Page 150: A Plan Of Action
If Something Goes Wrong Resolving a hardware conflict A plan of action The smooth operation of the system depends on the interaction of all devices, programs, and features. If the system or one of its attached devices is not working, resolving the problem can be time- consuming and frustrating.
Page 151: Memory Problems
If Something Goes Wrong Resolving a hardware conflict Checking device properties Device Manager provides a way to view the properties of a device. Properties include the name of the manufacturer, the type of device, the drivers installed, and the system resources assigned to the device.
Page 152: Power And The Batteries
If Something Goes Wrong Resolving a hardware conflict Reinstall the memory module, following the instructions in “Installing a memory module” on page 48, and making sure the module is seated properly. Check for the error again. If the error recurs, remove the memory module entirely and check for the error again.
Page 153: Keyboard Problems
After a period of time, the battery will lose its ability to perform at maximum capacity and will need to be replaced. This is normal for all batteries. To purchase a new battery pack, see your accessories information that shipped with your computer, or visit the Toshiba Web site at accessories.toshiba.com.
Page 154: Display Problems
If Something Goes Wrong Resolving a hardware conflict Nothing happens when you press the keys on the external keyboard. You may have plugged the external keyboard in while the computer was turned on. Using the computer’s TouchPad: Click Start, and then click the arrow next to the Lock button in the lower-right part of the Start menu.
Page 155 If Something Goes Wrong Resolving a hardware conflict The screen does not look right. You can change the display settings by clicking a blank area of the desktop with the secondary control button, then clicking Personalize. This opens the Personalization window. Click Windows Color and Appearance to choose the colors for the screen.
Page 156: Disk Drive Problems
If Something Goes Wrong Resolving a hardware conflict Small bright dots appear on your TFT display when you turn on your computer. Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precision technology.
Page 157 If Something Goes Wrong Resolving a hardware conflict You can choose one or both options: ❖ Automatically fix file system errors ❖ Scan for and attempt recovery of bad sectors Click Start. Error-checking tests and repairs the disk. Your hard disk seems very slow. If you have been using your computer for a long time, your files may have become fragmented.
Page 158: Optical Drive Problems
For more information regarding supported optical media formats, refer to the complete detail specifications for your computer at pcsupport.toshiba.com. If the problem is with a data CD or DVD, refer to the software’s documentation and check that the hardware configuration meets the...
Page 159: Sound System Problems
If Something Goes Wrong Resolving a hardware conflict The disc will not come out of the drive when you click the eject button on the screen. Press the button on the optical drive itself. For additional information see “You press the disc eject button, but the drive tray does not slide out.”...
Page 160 If Something Goes Wrong Resolving a hardware conflict PC Card checklist ❖ Make sure the card is inserted properly into the slot. ❖ Make sure all cables are securely connected. ❖ Occasionally a defective PC Card slips through quality control. If another computer with a PC Card slot is available, try the card in that machine.
Page 161: Expresscard™ Problems
If Something Goes Wrong Resolving a hardware conflict Select the item you wish to remove and click OK. Remove the device when told it is safe to do so. Never swap modules when the computer is in Hibernation or Sleep mode.
Page 162 If Something Goes Wrong Resolving a hardware conflict ExpressCard™ checklist ❖ Make sure the card is inserted properly into the slot. ❖ Make sure all cables are securely connected. ❖ Occasionally a defective ExpressCard slips through quality ™ control. If another computer with a ExpressCard slot is available, try the card in that machine.
Page 163: Printer Problems
If Something Goes Wrong Resolving a hardware conflict Select the item you wish to remove and click OK. Remove the device when told it is safe to do so. Never swap modules when the computer is in Hibernation or Sleep mode.
Page 164: Modem Problems
Make sure the line has a dial tone. Connect a telephone handset to the line to check this. The other system may be busy or off line. Try making a test transmission to someone else. For more information regarding your system’s V.92 modem, visit the Toshiba Web site at pcsupport.toshiba.com.
Page 165: Wireless Networking Problems
To determine if your computer has an internal Wi-Fi adapter, check ® the device list in Device Manager (part of the Windows Control Panel, Hardware and Sound). Some Toshiba models may have a ® Wi-Fi antenna switch even though they do not have an internal ®...
Page 166 If Something Goes Wrong Resolving a hardware conflict Verify that the DHCP Enabled setting is set to Yes. Click Close. ❖ Use IPCONFIG to verify that the computer has a useful IP address—one other than the private address of ® 169.254.xxx.xxx assigned by Windows Click Start to open the Start menu.
Page 167 If Something Goes Wrong Resolving a hardware conflict ® Special considerations for the Windows operating system Wired Equivalent Privacy (WEP) encryption is not enabled on the wireless access point. ® When you install a wireless access point device, the Windows operating system checks whether WEP encryption is enabled on the ®...
Page 168: Dvd Operating Problems
“Checking device properties” on page 151 for instructions on using Device Manager to view the optical drive properties. Check the Toshiba Web site for new information on optical drives and their operation. A blank screen appears while watching a DVD-ROM movie or title.
Page 169: Develop Good Computing Habits
If Something Goes Wrong Develop good computing habits Develop good computing habits Save your work frequently. You can never predict when your computer will lock, forcing you to close a program and lose unsaved changes. Many software programs build in an automatic backup, but you should not rely solely on this feature.
Page 170: Data And System Configuration Backup In The Windows
If Something Goes Wrong Develop good computing habits Read the user’s guides. It is very difficult to provide a fail-safe set of steps you can follow every time you experience a problem with the computer. Your ability to solve problems will improve as you learn about how the computer and its software work together.
Page 171 If Something Goes Wrong Develop good computing habits In the input field, enter a name that is descriptive enough to be easily understood in the future, such as “Before installing Brand X Accounting app.” Then click Create. ® The Windows operating system creates the Restore Point, automatically stamps it with the current date and time, and displays a message that the restore point was successfully...
Page 172 DVDs, or hard drives. An external hard drive is recommended in case the internal hard drive fails. No additional software is required. Most of the CD and DVD drives built into recent Toshiba portable computer models can write to (or ‘burn’) as well as read from CDs.
Page 173 If Something Goes Wrong Develop good computing habits General tips for installing hardware and software Here are a few tips to help ensure safe and easy installation of new hardware (printers, pointing devices, external hard drives, DVD ® writers, scanners, etc.) and software (applications like Microsoft ®...
Page 174: If You Need Further Assistance
For the complete detailed specifications for your computer, visit pcsupport.toshiba.com. Go to the Tech Support Center, select your particular model from the list and go to the Detailed Specifications for that model. For the number of a Toshiba dealer near you in the United States, call: (800) 457-7777.
Page 175: Contacting Toshiba
Toshiba’s Technical Support Web site For technical support, or to stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com Toshiba voice contact Before calling Toshiba, make sure you have: ❖...
Page 176: Toshiba's Worldwide Offices
20041, Agrate Brianza Japan Milano, Italy Latin America and Caribbean Mexico Toshiba America Information Toshiba de México S.A. de C.V. Systems Sierra Candela No.111, 6to. Piso 9740 Irvine Blvd. Col. Lomas de Chapultepec. Irvine, California 92618 CP 11000 Mexico, DF.
Page 177 Toshiba’s worldwide offices United States The Rest of Europe Toshiba America Information Toshiba Europe (I.E.) GmbH Systems, Inc. Hammfelddamm 8 9740 Irvine Boulevard D-4-1460 Neuss Irvine, California 92618 Germany United States For more information on additional Toshiba worldwide locations, please visit: www.toshiba.co.jp/index.htm.
Page 178: Appendix A: Hot Keys
Appendix A Hot Keys Hot keys provide a quick way to modify selected system functions and to launch applications. Hot Keys The hot keys are used to modify the following system functions: ❖ Mute ❖ Password security ❖ Power Plan ❖...
Page 179: Hot Key Functions
Hot Keys Hot key functions Hot key functions This section lists available hot key functions. NOTE Hot keys are keys that, when pressed in combination with the key, turn system functions on and off. Hot keys have a legend on the key indicating the option or feature the key controls.
Page 180: Power Plan
Hot Keys Hot key functions Power plan This hot key displays the power plans and cycles through the power plans. The properties of each power plan, and the power plans that are displayed by this function, are set in the Power Options window.
Page 181: Hibernation Mode
Hot Keys Hot key functions Hibernation mode This hot key places the computer into Hibernation mode. If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernation mode” on page Display modes This hot key cycles through the power-on display options.
Page 182: Display Brightness
Hot Keys Hot key functions Display brightness This hot key decreases or increases the screen brightness. This hot key decreases the screen brightness. This hot key increases the screen brightness. Pressing either hot key displays the following options: (Sample Image) Display brightness Move the slider or press the appropriate hot key repeatedly to decrease or increase the display brightness.
Page 183: Disabling Or Enabling The Touchpad
Hot Keys Hot key functions Disabling or enabling the TouchPad This hot key enables/disables the TouchPad. For more information on using the TouchPad, see “Disabling or enabling the TouchPad™” on page Pressing the hot key displays the following options: (Sample Image) Disable or Enable TouchPad options ❖...
Page 184: Appendix B: Power Cord/Cable Connectors
Appendix B Power Cord/Cable Connectors Your notebook computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cord/cable connectors for various parts of the world. USA and Canada United Kingdom UL approved CSA approved BS approved...
Page 185: Glossary
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide. alternating current BIOS basic input/output system bits per second compact disc CD-ROM compact disc read-only memory CD-RW compact disc rewrite memory CMOS...
Page 186 Glossary disk operating system dots per inch DSTN dual supertwist nematic digital versatile (or video) disc DVD-ROM digital versatile (or video) disc read-only memory enhanced capabilities port EPROM erasable programmable read-only memory file allocation table Federal Communications Commission gigabyte hard disk drive HTML Hypertext Markup Language IEEE...
Page 187 Glossary SDRAM synchronous dynamic random access memory SRAM static random access memory SVGA super video graphics adapter thin film transistor universal serial bus uniform resource locator wide area network World Wide Web Terms The following terms may appear in this user’s guide. active-matrix display —...
Page 188 Glossary baud rate — The speed at which a communication device, such as a printer or modem, transmits information. Baud rate is the number of signal changes per second (not necessarily the same as bits per second). See also bits per second. BIOS (basic input/output system) —...
Page 189 Glossary central processing unit (CPU) — The chip that functions as the “brain” of the computer. It takes information from outside sources, such as memory or keyboard input, processes the information, and sends the results to another device that uses the information. character —...
Page 190 Glossary device — A component attached to the computer. Devices may be external (outside the computer’s case) or internal (inside the computer’s case). Printers, disk drives, and modems are examples of devices. device driver — A program (called a “driver”) that permits a computer to communicate with a device.
Page 191 Glossary double-density diskette — A 3.5-inch diskette that can hold up to 720 KB of information (half the capacity of a high-density diskette). See also diskette, high-density diskette. download — (1) In communications, to receive a file from another computer through a modem or network. (2) To send font data from the computer to a printer.
Page 192 — The physical components of a computer system. Compare software. Hibernation — A feature of many Toshiba notebook computers that saves to the hard disk the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned off.
Page 193 Glossary hot key — (1) A feature in which certain keys in combination with the key can set system options or control system parameters, such as the battery save mode. (2) A key or combination of keys that activates a memory resident program. hot swapping —...
Page 194 Glossary local area network — See LAN. logical drive — A section of a disk that is recognized by the operating system as a separate disk drive. A system’s logical drives may differ from its physical drives. For example, a single hard disk drive may be partitioned into two or more logical drives.
Page 195 Glossary non-system disk — A disk for storing programs and data that cannot be used to start the computer. Compare system disk. online — Available through the computer. Online may refer to information being read from your own computer’s hard disk, such as online documentation or online Help, or to information coming from another company on a company network or the Internet.
Page 196 Glossary port — A socket on the computer where you plug in a cable for connection to a network or a peripheral device. processor — See central processing unit (CPU). program — A set of instructions that can be executed by a computer. The general classes of programs (also called software) are operating system, application, and utility.
Page 197 Glossary select — To highlight or otherwise specify text, data, or graphics with the intent to perform some operation on it. serial — Processes that occur one at a time. In communications, it means the transmission of one bit at a time sequentially over a single channel.
Page 198 Glossary Web — See World Wide Web. ® Wi-Fi — A registered trademark term of the Wi-Fi Alliance that stands for Wireless Fidelity, and is another term for the communication protocol to permit an Ethernet connection using wireless communication components. World Wide Web (www) —...
Page 199: Index
Index power plan 180 power plan hot key 107 AC adaptor 42 real-time clock (RTC) 99 AC power removing 108 connecting adaptor 43 Bridge Media Adapter accessories inserting memory media 130 memory 47 removing memory media 131 adding memory 47 button Alt keys 84 power 47...
Page 200 Index cleaning 79 external monitor not working 155 moving 80 screen is blank 154 non-system disk or disk error display device message 147 external 65 not accessing disk drives 146 display output settings 66 running on battery power 98 display, external setting up 40 adjusting 67 warning resume failure message...
Page 201 Index not working 155 recycle bin 116 mouse 67 safety 35 external diskette drive installation connecting 69 memory module 48 external display, adjusting 67 installing memory modules 47 mouse 67 FAT (File Allocation Table) 156 Internet file extensions 90 bookmarked site not found 149 file, backing up 82 connecting to 123 files...
Page 202 Index memory troubleshooting 158 adding 47 other documentation 36 problem solving 151 overlay keys 85 removing expansion slot cover 50 memory module PC Card inserting 51 checklist 160 installation 48 computer stops working 160 removing 55 configuring 128 microphone 125 errors 161 modem hot swapping fails 160...
Page 203 PC Card Startup options 147 inserted 160 URL address not found 148 computer will not power up 145 warning resume failure 146 contacting Toshiba 174 Windows® operating system not corrupted/damaged data files 157 working 147 Device Manager 150 program, starting 86...
Page 204 Taskbar 117 wireless networking 122 telephone line Wizards connecting to modem 119 Dial-Up Networking Wizard 120 television World Wide Web 123 adjusting display 67 www 123 Toshiba registering computer 41 worldwide offices 176 TOSHIBA Assist 133 Toshiba online resources 97...

This manual is also suitable for:

Satellite l45 series Satellite l40 Satellite l40 series

Toshiba L45-S7423 - Satellite - Pentium Dual Core 1.46 GHz User Manual

Chapter 1: Getting Started

Chapter 2: Learning the Basics

Chapter 3: Mobile Computing

Chapter 4: Exploring Your Computer's Features

Chapter 5: Utilities

Chapter 6: If Something Goes Wrong

Appendix A: Hot Keys

Appendix B: Power Cord/Cable Connectors

Quick Links

Related Manuals for Toshiba L45-S7423 - Satellite - Pentium Dual Core 1.46 GHz

Summary of Contents for Toshiba L45-S7423 - Satellite - Pentium Dual Core 1.46 GHz

This manual is also suitable for:

Table of Contents