Page 30
256MB A DATA MDOAD5F3G31Y0D1E02 DDR400 N/A ADD8608A8A-5B 512MB A DATA MDOAD5F3H41Y0D1E02 DDR400 N/A ADD8608A8A-5B 256MB A DATA MDOHY6F3G31Y0N1E0Z DDR400 Hynix HY5DU56822CT-D43 512MB A DATA MDOHY6F3H41Y0N1E0Z DDR400 Hynix HY5DU56822CT-D43 256MB A DATA MDOSS6F3G31Y0K1E0Z DDR400 SAMSUNG K4H560838E-TCCC 512MB A DATA MDOSS6F3H41Y0N1E0Z DDR400 SAMSUNG K4H560838E-TCCC 256MB Aeneon...
Page 50
• • A:\>afudos /oOLDBIOS1.ROM A:\>afudos /oOLDBIOS1.ROM AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading flash ..done A:\>...
Page 51
A:\>afudos /iP5GPLXS.ROM A:\>afudos /iP5GPLXS.ROM AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading file ..done Erasing flash ..done Writing flash ..0x0008CC00 (9%) A:\>afudos /iP5GPLXS.ROM AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc.
Page 52
Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Floppy found! Reading file “P5GPLXS.ROM”. Completed. Start flashing...
Page 53
Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Floppy not found! Checking for CD-ROM... CD-ROM found. Reading file “P5GPLXS.ROM”. Completed. Start flashing...
Page 58
System Time [11:51:19] Use [ENTER], [TAB] System Date [Thu 01/19/2006] or [SHIFT-TAB] to Legacy Diskette A [1.44M, 3.5 in] select a field. Primary IDE Master : [ST320413A] Use [+] or [-] to Primary IDE Slave : [Not Detected] configure system time. Third IDE Master : [Not Detected] Third IDE Slave...
Page 59
Language [English] Use [+] or [-] to Primary IDE Master :[ST320413A] configure system time. Primary IDE Slave :[ASUS CD-S340] Secondary IDE Master :[Not Detected] Secondary IDE Slave :[Not Detected] Third IDE Master :[Not Detected] Fourth IDE Master...
Page 60
System Time [11:51:19] Use [ENTER], [TAB] System Date [Thu 01/19/2006] or [SHIFT-TAB] to Legacy Diskette A [1.44M, 3.5 in] select a field. Primary IDE Master : [ST320413A] Use [+] or [-] to Primary IDE Slave : [Not Detected] configure system time. Third IDE Master : [Not Detected] Third IDE Slave...
Page 61
Primary IDE Master Device : Hard Disk Vendor : ST320413A Size : 20.0GB LBA Mode : Supported Block Mode : 16 Sectors PIO Mode : Supported Async DMA : MultiWord DMA-2 Ultra DMA : Ultra DMA-5 SMART Monitoring: Supported Type [Auto] LBA/Large Mode [Auto]...
Page 62
IDE Configuration Onboard IDE Operate Mode [Enhanced Mode] Enhanced Mode Support On [S-ATA] IDE Detect Time Out (Sec) [35] 2-16...
Page 67
USB Configuration Module Version - 2.24.0-10.4 USB Devices Enabled: None USB Function [Enabled] Legacy USB Support [Auto] USB 2.0 Controller [Enabled] USB 2.0 Controller Mode [HiSpeed] 2-21...
Page 68
Configure Advanced CPU settings Sets the ratio between CPU Core Clock and the Manufacturer: Intel FSB Frequency. Brand String: Genuine Intel(R) CPU 3.20GHz NOTE: If an invalid Frequency : 3200 MHz ratio is set in CMOS FSB Speed : 800 MHz then actual and Cache L1 : 16 KB...
Page 69
® ® • • Advanced Chipset Settings Configure DRAM Timing by SPD [Enabled] Hyper-Path 2 [Auto] Graphic Adapter Priority [PCI Express/PCI] PEG Buffer Length [Auto] Link Latency [Auto] PEG Link Mode [Auto] PEG Root Control [Auto] Slot Power [Auto] 2-23...
Page 71
Configure Win627EHF Super IO Chipset Enable or Disable High Definition Audio HD Audio Controller [Enabled] Controller Onboard LAN [Enabled] LAN Option ROM [Disabled] Serial Port1 Address [3F8/IRQ4] Parallel Port Address [378] Parallel Port Mode [ECP] ECP Mode DMA Channel [DMA3] Parallel Port IRQ [IRQ7] 2-25...
Page 72
Advanced PCI/PnP Settings WARNING: Setting wrong values in below sections may cause system to malfunction. Plug And Play O/S [No] PCI Latency Timer [64] Allocate IRQ to PCI VGA [Yes] Palette Snooping [Disabled] IRQ-3 assigned to [PCI Device] IRQ-4 assigned to [PCI Device] IRQ-5 assigned to [PCI Device]...
Page 73
Configure CPU. Suspend Mode [Auto] Repost Vedio on S3 Resume [No] ACPI 2.0 Support [No] ACPI APIC Support [Enabled] APM Configuration Hardware Monitor 2-27...
Page 74
APM Configuration Enabled or disable APM. Power button Mode [On/Off] Restore on AC Power Loss [Power Off] Resume On RTC Alarm [Disabled] Resume On By External Modems [Disabled] Resume On By PCI/PCIEX Devices [Disabled] Power On By PS/2 Keyboard [Disabled] Keyboard Wakeup Password : Not Installed Power On By PS/2 Mouse [Disabled]...
Page 76
Hardware Monitor CPU Temperature [51ºC/122.5ºF] MB Temperature [41ºC/105.5ºF] CPU Fan Speed [3813 RPM] CPU Q-Fan Control [Disabled] Chassis Fan Speed [N/A] VCORE Voltage [ 1.320V] 3.3V Voltage [ 3.345V] 5V Voltage [ 5.094V] Select Screen 12V Voltage [11.880V] Select Item Change Option General Help Save and Exit...
Page 77
APM Configuration Boot Device Priority Boot Settings Configuration Security Select Screen Select Item Enter Go to Sub-screen General Help Save and Exit Exit 2-31...
Page 78
Boot Device Priority 1st Boot Device [1st FLOPPY DRIVE] 2nd Boot Device [PM-ST330620A] 3rd Boot Device [PS-ASUS CD-S360] Hard Disk Drives 1st Drive [XXXXXXXXX] 2nd Drive [XXXXXXXXX] Boot Settings Configuration Allows BIOS to skip certain tests while Quick Boot [Enabled] booting.
Page 80
Security Settings <Enter> to change password. Supervisor Password : Not Installed <Enter> again to User Password : Not Installed disabled password. Change Supervisor Password 2-34...
Page 81
Security Settings Supervisor Password : Not Installed User Password : Not Installed Change Supervisor Password User Access Level [Full Access] Change User Password Clear User Password Password Check [Setup] 2-35...
Page 82
Exit Options Exit system setup after saving the Exit & Save Changes changes. Exit & Discard Changes Discard Changes F10 key can be used for this operation. Load Setup Defaults Select Screen Select Item Enter Go to Sub-screen General Help Save and Exit Exit 2-36...