hit counter script
HP Kayak XA-s 02xx Manual
HP Kayak XA-s 02xx Manual

HP Kayak XA-s 02xx Manual

Hp kayak xa-s series 02xx, installing accessories for desktop models
Hide thumbs Also See for Kayak XA-s 02xx:

Advertisement

HP Kayak XA-s 02xx PC Workstation -
Installing Accessories In Your
HP Desktop PC Workstation
Explains in detail how to install accessories, such as extra memory,
accessory boards, and additional disk drives.

Advertisement

Table of Contents
loading

Summary of Contents for HP Kayak XA-s 02xx

  • Page 1 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Explains in detail how to install accessories, such as extra memory, accessory boards, and additional disk drives.
  • Page 2: Supported Hp Accessories

    HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Supported HP Accessories Supported HP Accessories Internal Mass Storage Devices Front Access Drives, for example: - 5.25-inch CD-ROM drive (half height) - 3.5-inch 1.44 MB floppy disk drive...
  • Page 3: Removing And Replacing The Cover

    HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Removing and Replacing the Cover Removing and Replacing the Cover WARNING For your safety, never remove the PC Workstation’s cover without first removing the power cord from the power outlet, and any connection to a telecommunications network.
  • Page 4: Replacing The Cover

    HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Removing and Replacing the Cover Replacing the Cover 1 Ensure that you have installed all your accessories and that all internal cables are properly connected and safely routed.
  • Page 5: Moving The Power Supply

    HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Moving the Power Supply Moving the Power Supply You can move the power supply unit out of the computer to improve access to the system board and the cables at the rear of the disk drives.
  • Page 6 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Moving the Power Supply Replacing the Power 1 Check that all internal cables are safely routed. Supply after Installing 2 Rotate the power supply into the computer. Tilt the back of the Accessories power supply unit until it engages with the computer’s case.
  • Page 7: Installing Memory

    HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Memory Installing Memory Main Memory Modules If you need more main memory to run your application software, you can install up to 768 MB of memory in three 100 MHz DIMM slots.
  • Page 8 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Memory The location of the memory module slots is shown below. 5 Slide the memory module into the slot at 90° to the system board (with the cutouts furthest away from the processor).
  • Page 9 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Memory 7 Repeat this procedure for each additional memory module you want to install. 8 Install any other accessories if necessary, then replace all units and reconnect all cables and power cords.
  • Page 10: Installing Mass Storage Devices

    HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices Installing Mass Storage Devices The computer has two internal shelves (for hard disk drives) and two front-access drive shelves (for front-access drives).
  • Page 11 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices Which Data Your PC Workstation has the following cables and connectors which can be used for mass storage devices: Connectors to Use A floppy disk drive cable with a single connector (connected to the •...
  • Page 12 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices Installing a Hard This PC Workstation has integrated Dual Ultra ATA-33 IDE controllers and, on selected models, an Ultra SCSI interface board.
  • Page 13: Installing A Hard Disk Drive In An Internal Shelf

    HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices Installing a Hard Disk Drive in an Internal Shelf NOTE The internal shelves can house one hard disk drive that is up to 1.6-inches in height, and one hard disk drive up to 1-inch in height.
  • Page 14 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices 7 If you want to install the new hard drive in the shelf of the existing drive, remove the four retaining screws from the top of the hard drive’s unit and remove the drive.
  • Page 15 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices 9 For a drive in the upper shelf, tighten the four retaining screws on top of the hard drive’s unit. For a drive in the lower shelf, use the four spare screws from the top (center) of the hard drive unit, to secure the hard disk drive on either side.
  • Page 16 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices 11 Lower the hard drive unit back into the PC Workstation’s case and tighten the four (outer) retaining screws. 12 Install any other accessories before completing the installation.
  • Page 17 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices Completing the Installation of a Hard Disk Drive When a SCSI Hard 1 Switch on the computer. Disk Drive Is Installed...
  • Page 18: Installing A Drive In A Front-Access Shelf

    HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices Installing a Drive in a Front-Access Shelf These instructions explain how to install a drive (such as a floppy disk drive, CD-ROM drive, CD-RW drive, or tape drive) in one of the front- access drive shelves.
  • Page 19 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices 4 Press the retaining buttons on each side of the HP UltraFlow airflow guide and remove it from the PC Workstation’s case.
  • Page 20 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices 8 Connect the data and power cables to the rear of the device. (The connectors are shaped to go in one way only.)
  • Page 21: Installing Accessory Boards

    HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Accessory Boards Installing Accessory Boards CAUTION Static electricity can damage electronic components. Turn OFF all equipment. Don’t let your clothes touch the accessory. To equalize the static electricity, rest the accessory bag on top of the computer while you are removing the accessory from the bag.
  • Page 22 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Accessory Boards 5 Hold the board by its “top” edge. Slide it into the board guide of the chosen slot. Do not bend the board.
  • Page 23 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Accessory Boards Completing the If you have installed an ISA accessory board that uses an interrupt, you must run the Setup program and reserve the IRQ for the accessory Installation of an ISA board.
  • Page 24: Installing A Processor

    HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing a Processor Installing a Processor Some operating systems support a second processor for enhanced performance. Contact your authorized reseller for up-to-date information. NOTE The Setup program provides an option to disable the second processor.
  • Page 25 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing a Processor 6 The system board has two processor sockets and a VRM slot for each processor (refer to the illustrations below). a If you are changing the existing processor, remove it from the socket by squeezing the tabs at the top of the processor and gently pulling the processor away from the system board.
  • Page 26 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing a Processor NOTE If you want to install a faster processor, remove the one supplied with the computer. If two processors are to be installed, ensure that they are both the same speed (frequency).
  • Page 27 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing a Processor Completing the 1 Verify that the system board bus speed switches are correctly configured for the processor, as shown below. Installation of a...
  • Page 28 HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing a Processor 2 Install any other accessories before completing the installation of the processor. 3 Replace the cover (refer to page 4). 4 Turn on the computer and check that the new processor is recognized by the power-on system-test.

This manual is also suitable for:

Kayak xa-s 02 series

Table of Contents