Advertisement
Quick Links
Change Card Settings
This chapter explains how to change transmission settings on cards in a Cisco ONS 15600.
Before You Begin
As necessary, complete the
Before performing the following procedures, investigate all alarms and clear any trouble conditions.
Refer to the Cisco ONS 15600 Troubleshooting Guide as necessary.
This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).
1.
2.
3.
4.
5.
6.
7.
February 2008
"NTP-E57 Document Existing Provisioning" procedure on page
NTP-E157 Provision a Multirate PPM, page
pluggable port module (PPM), for the ASAP card. If a multirate PPM was preprovisioned, this
procedure is unnecessary.
NTP-E151 Provision an Optical Line Rate, page
optical line rate on a multirate PPM for the ASAP card. Single-rate PPMs do not need to be
provisioned.
NTP-E150 Change the Optical Line Rate, page
optical line rates for multirate PPMs on the ASAP card.
NTP-E149 Delete Pluggable Port Modules, page
delete PPMs for the ASAP card.
NTP-E66 Modify Line and Status Thresholds for Optical Ports, page
this procedure to change line (drop) and threshold settings for all OC-N cards.
NTP-E105 Change an Optical Port to SDH, page
change an optical port from SONET to SDH.
NTP-E125 Change Card Service State, page
card service state.
C H A P T E R
11-2—Complete this procedure to provision a multirate
11-3—Complete this procedure to provision the
11-4—As needed, complete this procedure to edit
11-5—As needed, complete this procedure to
11-6—As needed, complete
11-12—As needed, complete this procedure to
11-13—As needed, complete this procedure to change
Cisco ONS 15600 Procedure Guide, R5.0
11
7-2.
11-1
Advertisement
Related Manuals for Cisco NTP-E157
Summary of Contents for Cisco NTP-E157
-
Page 1: Before You Begin
C H A P T E R Change Card Settings This chapter explains how to change transmission settings on cards in a Cisco ONS 15600. Before You Begin As necessary, complete the “NTP-E57 Document Existing Provisioning” procedure on page 7-2. - Page 2 17-50 as necessary. Verify that no unexplained conditions appear on the network. If unexplained conditions appear, resolve them before continuing. Refer to the Cisco ONS 15600 SONET Troubleshooting Guide. Complete the “DLP-E76 Export CTC Data” task on page 16-98 to export alarm and condition information.
- Page 3 17-50 as necessary. Verify that no unexplained conditions appear on the network. If unexplained conditions appear, resolve them before continuing. Refer to the Cisco ONS 15600 SONET Troubleshooting Guide. Complete the “DLP-E76 Export CTC Data” task on page 16-98 to export alarm and condition information.
- Page 4 17-50 as necessary. Verify that no unexplained conditions appear on the network. If unexplained conditions appear, resolve them before continuing. Refer to the Cisco ONS 15600 SONET Troubleshooting Guide. Complete the “DLP-E76 Export CTC Data” task on page 16-98 to export alarm and condition information.
- Page 5 17-50 as necessary. Verify that no unexplained conditions appear on the network. If unexplained conditions appear, resolve them before continuing. Refer to the Cisco ONS 15600 SONET Troubleshooting Guide. Complete the “DLP-E76 Export CTC Data” task on page 16-98 to export alarm and condition information.
- Page 6 (in service or out of service), and performance monitoring thresholds for OC-48, OC-192 cards, and OC-N ports on ASAP cards. Tools/Equipment None Prerequisite Procedures NTP-E157 Provision a Multirate PPM, page 11-2 Required/As Needed As needed Onsite/Remote Onsite or remote...
- Page 7 Type Defines the port as SONET or SDH. SONET (default) • Enable Sync Msg and Send Do Not Use • must be disabled before the port can be set to SDH. Cisco ONS 15600 Procedure Guide, R5.0 11-7 February 2008...
- Page 8 Enable Sync Enables synchronization status messages Yes (checked, default) • Messages (S1 byte), which allow the node to choose No (unchecked) • the best timing source Click Apply. Step 6 Cisco ONS 15600 Procedure Guide, R5.0 11-8 February 2008...
- Page 9 Click Line, Section, Path, or Physical to provision the line, section, path, and physical options in Table 11-3 for each OC-N port. Change the selection to Near End/Far End, 15 Min/1Day as necessary. Click Refresh to view or modify the thresholds for each selection. Cisco ONS 15600 Procedure Guide, R5.0 11-9 February 2008...
- Page 10 500/5000 (Near End); 0/0 (Far End) • Path • 3/7 (OC-48/OC-192 Near and Far End) SEFS Severely errored framing seconds Numeric. Defaults (15 min/1 day): Section 500/5000 (Near End); 0/0 (Far End) • Cisco ONS 15600 Procedure Guide, R5.0 11-10 February 2008...
- Page 11 Click Physical to provision the physical options in Table 11-4 for each OC-N port. Change the selection to 15 Min or 1 Day as necessary. Click Refresh to view or modify the thresholds for each selection. Cisco ONS 15600 Procedure Guide, R5.0 11-11 February 2008...
- Page 12 Double-click the OC-N card where you want to provision a port for SDH. Step 2 Step 3 Click the Provisioning > Line tabs. Step 4 In the Type field, specify the port and choose SDH. Step 5 Click Apply. Cisco ONS 15600 Procedure Guide, R5.0 11-12 February 2008...
- Page 13 Admin State chosen. For more information about the enhanced state model and card state transitions, refer to the “Administrative and Service States” appendix of the Cisco ONS 15600 Reference Manual. Table 11-5...
- Page 14 Chapter 11 Change Card Settings NTP-E125 Change Card Service State Table 11-5 Cisco ONS 15600 Card State Transitions (continued) Admin State Original Service State Next Service State OOS,MT OOS-AU,AINS & UEQ OOS-AUMA,MT & UEQ (Out-of-Service and Autonomous,Auto (Out-of-Service and Autonomous...