BLOCK DIAGRAM ..........36 (A02-3881-13)(2CH): K LEVEL DIAGRAM ..........38 (A02-3882-03)(8CH): K2 KSC-31 / KNB-29N / KBH-10 ......39 SPECIFICATIONS ......BACK COVER Knob (PTT) (K29-9308-03) Photo is TK-2200 (K2 type). Does not come with antenna. Antenna is available as an option.
TK-2200 GENERAL INTRODUCTION PERSONAL SAFETY SCOPE OF THIS MANUAL The following precautions are recommended for personal This manual is intended for use by experienced technicians safety: familiar with similar types of commercial grade communications DO NOT transmit until all RF connectors are verified secure ●...
98, ME, Windows 2000 or XP on an IBM-PC or compatible the volume. machine. The data can be input to or read from TK-2200 and edited on the screen. The programmed or edited data can be printed PTT (Push to out.
TK-2200 REALIGNMENT • The Master Unit and Slave Unit must be of the same model 5. Clone Mode type and destination in order for Clone to operate. 5-1. Outline • Clone mode cannot be accessed if “Super Lock” is "Clone Mode" copies the transceiver data to another activated.
TK-2200 DISASSEMBLY FOR REPAIR ■ Removing the battery release lever from the case ■ Removing the case assembly from the chassis. assembly. 1. Remove the volume knob and channel knob (The stopper is contained in the channel knob only the 1.
Page 6
TK-2200 DISASSEMBLY FOR REPAIR ■ Assembling the battery release lever 2. Mounting the chassis to the case assembly. 1. Place the lever onto the stopper 1. Confirm that the waterproof packing attached to the 2. Place the thick spring onto the lever.
Page 7
TK-2200 DISASSEMBLY FOR REPAIR 3. Attaching the antenna receptacle to the 5. Connecting the speaker wires to the TX-RX chassis. unit Screw the antenna receptacle to the chassis in the order Note: To connect the speaker wires, you must solder it to the shown in the drawing so that the antenna receptacle comes location of the TX-RX unit as illustrated below.
TK-2200 CIRCUIT DESCRIPTION 3) IF Amplifier Circuit 1. Frequency Configuration The first IF signal is passed through a four-pole monolithic The receiver utilizes double conversion. The first IF is 38.85 crystal filter (XF201) to remove the adjacent channel signal. MHz and the second IF is 450 kHz. The first local oscillator The filtered first IF signal is amplified by the first IF amplifier signal is supplied from the PLL circuit.
Page 9
TK-2200 CIRCUIT DESCRIPTION 6) Squelch 2) VCO Part of the AF signal from the IC enters the FM IC (IC201) The operating frequency is generated by Q4 in transmit again, and the noise component is amplified and rectified mode and Q3 in receive mode. The oscillator frequency is...
TK-2200 CIRCUIT DESCRIPTION IC301 The QT,DQT data of the QTVCO Line is output from pin 24 of the CPU. The signal passes through a low pass CR filter, mixes with the audio signal, and goes to the VCO modulation AQUA input.
Page 11
TK-2200 CIRCUIT DESCRIPTION 7. Control System Keys and channel selector circuit. XOUT The signal from the keys and channel selector are directly IC405 input to the microprocessor, as shown in fig. 11. Q407 Q408 Channel selector Hi: OFF BSHIFT LOW: ON Fig.
TK-2200 TERMINAL FUNCTION / SEMICONDUCTOR DATA TERMINAL FUNCTION ■ CN401 Name Function Name Function B (Battery Voltage) Encoder pulse input Switched B Audio input Encoder pulse input Audio output Encoder pulse input Encoder pulse input Encoder pulse input SEMICONDUCTOR DATA Microprocessor : 30622MAA-B91GP (TX-RX UNIT : IC405) ■...
TK-2200 COMPONENTS DESCRIPTION TX-RX UNIT (X57-6880-XX) Ref. No. Use/Function Operation/Condition Ref. No. Use/Function Operation/Condition PLL system Diode Ripple Filter VCO 1/2 Divider Variable Frequency control / TX VCO IC101 Comparator (APC) Capcitance Diode IC201 FM IF system Variable Frequency control / RX VCO...
TK-2200 PARTS LIST CAPACITORS CC 45 TH 1H Capacitor value Color* CC45 010 = 1pF 0 = 22pF 1 = Type ... ceramic, electrolytic, etc. 100 = 10pF 4 = Voltage rating Multiplier 2 = Shape ... round, square, ect.
Page 15
E: Europe Les articles non mentionnes dans le Parts No. ne sont pas fournis. Y: AAFES (Europe) X: Australia M: Other Areas Teile ohne Parts No. werden nicht geliefert. TK-2200 (Y50-5910-XX) TX-RX UNIT (X57-6880-XX) Ref. No. Address Parts No. Description Destination Ref.
Page 16
TK-2200 PARTS LIST TX-RX UNIT (X57-6880-XX) Ref. No. Address Parts No. Description Destination Ref. No. Address Parts No. Description Destination parts parts CK73GB1A105K CHIP C 1.0UF C141 CC73GCH1H120J CHIP C 12PF CC73HCH1H101J CHIP C 100PF C142 CC73GCH1H300J CHIP C 30PF...
Page 17
TK-2200 PARTS LIST TX-RX UNIT (X57-6880-XX) Ref. No. Address Parts No. Description Destination Ref. No. Address Parts No. Description Destination parts parts C255 CC73GCH1H4R5B CHIP C 4.5PF C405 CC73GCH1H101J CHIP C 100PF C256 CK73HB1H102K CHIP C 1000PF K C407 CK73HB1H102K...
Page 18
TK-2200 PARTS LIST TX-RX UNIT (X57-6880-XX) Ref. No. Address Parts No. Description Destination Ref. No. Address Parts No. Description Destination parts parts L115 L34-4563-05 AIR-CORE COIL RK73HB1J472J CHIP R 4.7K J 1/16W L116 L34-4576-05 AIR-CORE COIL RK73HB1J101J CHIP R J 1/16W...
Page 19
TK-2200 PARTS LIST TX-RX UNIT (X57-6880-XX) Ref. No. Address Parts No. Description Destination Ref. No. Address Parts No. Description Destination parts parts R238 RK73GB1J104J CHIP R 100K J 1/16W R408-412 RK73HB1J473J CHIP R J 1/16W R239 RK73GB1J470J CHIP R J 1/16W...
Page 20
TK-2200 PARTS LIST TX-RX UNIT (X57-6880-XX) Ref. No. Address Parts No. Description Destination Ref. No. Address Parts No. Description Destination parts parts ∗ Q103 RD00HVS1 ∗ Q104 RT1N141U TRANSISTOR Q105 2SK879(Y) Q106 RD02MUS1 ∗ Q106 RD02MUS1-T22 ∗ Q107 RT1N141U TRANSISTOR...
TK-2200 EXPLODED VIEW 12(K) MIC301 TX-RX Unit CF201 A :N14-0819-04 B :N14-0820-04 C :N30-2604-46 D :N30-2606-46 E :N83-2005-46 Parts with the exploded numbers larger than 700 are not supplied.
2. Repair Jig (Chassis) power supply and the battery jig, especially while the Use jig (part No.: A10-4086-03) for repairing the TK-2200. transceiver transmits. Place the TX-RX unit on the jig and fit it with screws.
Page 24
TK-2200 ADJUSTMENT PTT (Push to Channel selector Antenna Talk) switch (optional) LED indicator Power switch/ Lock key Volume control Speaker/ microphone jacks Scan key Adjustment points Frequency (MHz) TX-RX unit (X57-688) Channel No. RX Frequency TX Frequency Component side view 162.050...
Page 25
TK-2200 ADJUSTMENT Common Section Measurement Adjustment Specifications/ Item Condition Remark Test equipment Terminal Parts Method 1.Setting 1) BATT terminal votage:7.5V 2) SSG standard modulation [Wide] MOD:1kHz,DEV:3kHz [Narrow] MOD:1kHz,DEV:1.5kHz 2.VCO lock 1) CH:High Power meter 2.3V ±0.1V voltage 2) CH:Low Check 0.6V or more...
Page 26
TK-2200 ADJUSTMENT Measurement Adjustment Specifications/ Item Condition Remark Test equipment Terminal Parts Method 7.DQT TEST CH: Center Power meter Programming Make the Balance Adjust Deviation meter Software:KPG-88D demodulation [Wide] High Oscilloscope wave into (3 points) square waves LPF:3kHz AF VTVM...
Page 27
TK-2200 ADJUSTMENT Receiver Section Measurement Adjustment Specifications/ Item Condition Remark Test equipment Terminal Parts Method 1.BPF Wave (1)Center frequency Spectrum Programming Adjust the REF -6.7 dBm 10dB/ A_Write Norm B_Blank Norm CENTER Adjust Spectrum analyzer setting analyzer Software: waveform as 162.0 MHz...
Page 37
TK-2200 SCHEMATIC DIAGRAM ● Note : The components marked with a dot ( ) are parts of layer1. TX-RX UNIT (X57-6880-XX) -10:K -11:K2 ANT SW D103 L119 L117 L118 HVC131 D104 C151 L113 L114 L115 C144 C154 C156 C159 CN13...
Page 38
TK-2200 SCHEMATIC DIAGRAM ● Note : The components marked with a dot ( ) are parts of layer1. TX-RX UNIT (X57-6880-XX) -10:K -11:K2 TX DRIVE AMP ANT SW D103 L117 L118 L119 4.74V R:7.53V TX FINAL AMP T:7.41V PLL_CLK T:3.42V T:4.89V...