hit counter script
Makita BHS630 Instruction Manual
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Power Tool
  5. BHS630
  6. Instruction manual
Makita BHS630 Instruction Manual

Makita BHS630 Instruction Manual

Hide thumbs Also See for BHS630:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Technical Information, Instruction Manual
INSTRUCTION MANUAL
Cordless Circular Saw
BHS630
012092
IMPORTANT: Read Before Using.
1

Advertisement

Table of Contents
loading

Related Manuals for Makita BHS630

Summary of Contents for Makita BHS630

  • Page 1 INSTRUCTION MANUAL Cordless Circular Saw BHS630 012092 IMPORTANT: Read Before Using.

  • Page 2: Specifications

    ENGLISH (Original instructions) SPECIFICATIONS Model BHS630 Blade diameter 165 mm at 90° 66 mm Max. Cutting depth at 45° 46 mm No load speed (min 3,100 Overall length 346 mm Net weight 3.5 kg Rated voltage D.C. 18V • Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
  • Page 3 If operating a power tool in a damp location is 20. Store idle power tools out of the reach of unavoidable, use a ground fault circuit children and do not allow persons unfamiliar interrupter (GFCI) protected supply. Use of an with the power tool or these instructions to GFCI reduces the risk of electric shock.

  • Page 4: Safety Warnings

    GEB061-3 uncontrolled saw to lift up and out of the workpiece toward the operator; CORDLESS CIRCULAR SAW − when the blade is pinched or bound tightly by SAFETY WARNINGS the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back DANGER: Keep hands away from cutting toward the operator;...
  • Page 5 12. Lower guard may be retracted manually only for special cuts such as "plunge cuts" and "compound cuts." Raise lower guard by retracting handle and as soon as blade enters the material, the lower guard must be released. For all other sawing, the lower guard should operate automatically.
  • Page 6 25. Keep blade sharp and clean. Gum and wood pitch hardened on blades slows saw and Fig. 1 increases potential for kickback. Keep blade clean by first removing it from tool, then cleaning it with gum and pitch remover, hot water or kerosene. Never use gasoline.

  • Page 7: Functional Description

    Be careful not to drop or strike battery. FUNCTIONAL DESCRIPTION Do not use a damaged battery. SAVE THESE INSTRUCTIONS. CAUTION: Always be sure that the tool is switched off and the Tips for maintaining maximum battery life • battery cartridge is removed before adjusting or Charge battery cartridge...

  • Page 8: Bevel Cutting

    NEVER use the tool if it runs when you simply pull the switch trigger without pressing the lock-off lever. Return tool a MAKITA service center for proper repairs BEFORE further usage.
  • Page 9 CAUTION: 2. Thumb screw Be sure the blade is installed with teeth pointing up • at the front of the tool. Use only the Makita wrench to install or remove the • blade. 1. Shaft lock 2. Hex wrench 012113 3.

  • Page 10: Operation

    Rip fence (Guide rule) 012149 When you wish to perform clean cutting operation, 1. Clamp lever connect a Makita vacuum cleaner to your tool. Install the 2. Rip fence (Guide rule) dust nozzle on the tool using the screw. Then connect a hose of the vacuum cleaner to the dust nozzle as shown in the figure.

  • Page 11: Optional Accessories

    But if it is off, you can adjust it as If you need any assistance for more details regarding the following procedure. these accessories, ask your local Makita Service Center. Make sure all levers and screws are tightened. Slightly Saw blades •...
  • Page 12 Makita Corporation www.makita.com 885071A6...

Table of Contents