hit counter script
Sharp LC-40LE810E Service Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. TV
  5. LC-40LE810E
  6. Service manual

Sharp LC-40LE810E Service Manual

Lcd colour television
Hide thumbs Also See for LC-40LE810E:
Table of Contents

Advertisement

Quick Links

See also: Operating Manual
TopPage
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its orig-
inal condition and only parts identical to those specified should be used.
SAFETY PRECAUTION
CAUTION ............................................... . ............i
End of life disposal ................................. . .......... iii
MAJOR SERVICE PARTS ..................... . ..........iv
CHAPTER 1. SPECIFICATIONS
[1]
SPECIFICATIONS ................................. . ....... 1-1
[1]
OPERATION MANUAL .......................... . ....... 2-1
[1]
DIMENSIONS (LC-40LE810E) .............. . ....... 3-1
[2]
DIMENSIONS (LC-46LE810E) .............. . ....... 3-2
[1]
(LC-40LE810E) ..................................... . ....... 4-1
[2]
(LC-46LE810E) ...................................... . ....... 4-6
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.

SERVICE MANUAL

LCD COLOUR TELEVISION
LC-40LE810E
LC-46LE810E
MODELS
CONTENTS
[1]
ADJUSTMENT PROCEDURE ......................5-1
[1]
TROUBLESHOOTING TABLE ......................6-1
[2]
error .............................................................6-13
[1]
MAJOR IC INFORMATIONS .........................7-1
[1]
(LC-40LE810E)..............................................8-1
[2]
(LC-46LE810E)..............................................8-2
[3]
SYSTEM BLOCK DIAGRAM .........................8-3
LC-40/46LE810E (1st Edition)
No. S30E940LE810E
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.

Advertisement

Table of Contents
loading

Related Manuals for Sharp LC-40LE810E

Summary of Contents for Sharp LC-40LE810E

  • Page 1: Table Of Contents

    OPERATION MANUAL ........2-1 (LC-40LE810E)..........8-1 OVERALL WIRING DIAGRAM CHAPTER 3. DIMENSIONS (LC-46LE810E)..........8-2 DIMENSIONS (LC-40LE810E) ...... 3-1 SYSTEM BLOCK DIAGRAM ......8-3 DIMENSIONS (LC-46LE810E) ...... 3-2 Parts Guide CHAPTER 4. REMOVING OF MAJOR PARTS REMOVING OF MAJOR PARTS (LC-40LE810E) ........

  • Page 2: Important Service Safety Pre

    LC-40/46LE810E (1st Edition) LC-40LE810E SAFETY PRECAUTION Service Manual IMPORTANT SERVICE SAFETY PRECAUTION Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow: WARNING • Use an AC voltmeter having with 5000 ohm per volt, or higher, sen- sitivity or measure the AC voltage drop across the resistor.

  • Page 3: Precautions For Using Lead-Free Solder

    LC-40/46LE810E (1st Edition) Precautions for using lead-free solder Employing lead-free solder • “PWBs” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder. Example: F a/a Indicates lead-free solder of tin, silver and copper.

  • Page 4: End Of Life Disposal

    LC-40/46LE810E (1st Edition) End of life disposal End of life disposal...

  • Page 5: Outline

    Therefore, please exchange of a TOUCH SENSOR Unit in the case of front cabinet exchange. OTHER UNIT Ref No. Parts Code Description R1LK400D3LWF2Y 40” LCD Panel Module Unit (LC-40LE810E) R1LK460D3LWA2Y 46” LCD Panel Module Unit (LC-46LE810E) IC FOR EXCLUSIVE USE OF THE SERVICE Ref No. Parts Code Description Q’ty...

  • Page 6: Specifications

    • As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

  • Page 7: Chapter 2. Operation Manual

    LC-40/46LE810E (1st Edition) CHAPTER 2. LC-40LE810E OPERATION MANUAL Service Manual [1] OPERATION MANUAL TV (front view) VOL -/+ (Volume buttons) (Programme [channel] buttons) INPUT (Input source button) MANU (Menu button) POWER (Power button) OPC sensor Remote control sensor Illumination LED...

  • Page 8: Remote Control Unit

    LC-40/46LE810E (1st Edition) Remote control unit (Standby/On) Exit the “Menu” screen. (Display information) Press to access conventional Press to display the station analogue TV mode. information (channel number, signal, etc.) in the upper right corner of the screen. Press to access digital TV mode. P.
  • Page 9 LC-40/46LE810E (1st Edition) Attaching the stand unit • Before performing work, spread cushioning over the surface on which you will be laying the TV. This will prevent it from being damaged. CAUTION Attach the stand in the correct direction. • Be sure to follow the instructions.

  • Page 10: Chapter 3. Dimensions

    LC-40/46LE810E (1st Edition) CHAPTER 3. LC-40LE810E DIMENSIONS Service Manual [1] DIMENSIONS (LC-40LE810E) Unit: mm 992.0 992,0 887.8 887,8 450.0 450,0 300.0 39.5 124.0 300,0 124,0 39,5 275.0 275,0 3 – 1...

  • Page 11: Dimensions (Lc-46Le810E)

    LC-40/46LE810E (1st Edition) [2] DIMENSIONS (LC-46LE810E) Unit: mm 1125.0 1125,0 1020.8 1020,8 540.0 540,0 400.0 39.5 157.1 400,0 157,1 39,5 340.0 340,0 3 – 2...

  • Page 12: Chapter 4. Removing Of Major Parts Removing Of Major Parts (Lc-40Le810E)

    CHAPTER 4. LC-40LE810E REMOVING OF MAJOR PARTS Service Manual [1] REMOVING OF MAJOR PARTS (LC-40LE810E) 1. Removing of Stand Unit and Rear Cabinet Ass’y. 1. Remove the 1 lock screw and detach the Support Cover 2. Remove the 4 lock screw and detach the Stand Unit 3.

  • Page 13: Main Unit

    LC-40/46LE810E (1st Edition) 2. Removing of Speaker-L/R. 1. Remove the 1 lock screw and detach the Stand Cover 2. Disconnect SP wire. 3. Detach the Speaker-L , Speaker-R 4. Detach the Insulation Sheet (AC) MAIN Unit [SP] Insulation Sheet (AC) [SP] Speaker-R 3 Speaker-L...
  • Page 14 LC-40/46LE810E (1st Edition) 3. Removing of 40” LCD Panel Module Unit, TOUCH SENSOR Unit, ICON Unit, R/C, LED Unit, Front Cabinet Ass’y. 1. Disconnect RA, SB wire. 2. Detach the TOUCH SENSOR Unit . (RK) 3. Detach the ICON Unit .
  • Page 15 LC-40/46LE810E (1st Edition) 4. Removing of Connectors 1. Disconnect the following connectors from the MAIN Unit. (LB, PD, LW) 2. Disconnect the following connectors from the POWER Unit. (L1, L2, LB, PD, PL, AS) 3. Disconnect the following connectors from the LCD CONTROL Unit. (LW, PL) POWER Unit MAIN Unit [LW]...
  • Page 16 LC-40/46LE810E (1st Edition) 5. Removing of MAIN Unit, POWER Unit, Woofer, Stand Angle. 1. Remove the 7 lock screws and detach the MAIN Unit 2. Remove the 2 lock screws and detach the Terminal Angle (Bottom) 3. Remove the 2 lock screws and detach the Terminal Angle (Side) 4.

  • Page 17: Removing Of Major Parts (Lc-46Le810E)

    LC-40/46LE810E (1st Edition) [2] REMOVING OF MAJOR PARTS (LC-46LE810E) 1. Removing of Stand Unit and Rear Cabinet Ass’y. 1. Remove the 1 lock screw and detach the Support Cover 2. Remove the 4 lock screws and detach the Stand Unit 3.
  • Page 18 LC-40/46LE810E (1st Edition) 2. Removing of Speaker-L/R. 1. Remove the 3 lock screws and detach the Stand Cover 2. Disconnect SP wire. 3. Detach the Speaker-L , Speaker-R 4. Detach the Insulation Sheet (AC) MAIN Unit [SP] Insulation Sheet (AC) [SP] Speaker-R 3 Speaker-L...
  • Page 19 LC-40/46LE810E (1st Edition) 3. Removing of 46” LCD Panel Module Unit, TOUCH SENSOR Unit, ICON Unit, R/C, LED Unit, Front Cabinet Ass’y. 1. Remove the 1 lock screw and detach the LCD Angle (Bottom-R) 2. Remove the 5 lock screws , 5 lock screws , 4 Hooks and detach the 46”...
  • Page 20 LC-40/46LE810E (1st Edition) 4. Removing of Connectors 1. Disconnect the following connectors from the MAIN Unit. (SB, LB, PD, LW) 2. Disconnect the following connectors from the POWER Unit. (L1, L2, LB, PD, PL, AS) 3. Disconnect the following connectors from the LCD CONTROL Unit. (LW, PL) POWER Unit MAIN Unit [LW]...
  • Page 21 LC-40/46LE810E (1st Edition) 5. Removing of MAIN Unit, POWER Unit, Sub Woofer, Stand Angle. 1. Remove the 7 lock screws and detach the MAIN Unit 2. Remove the 2 lock screws and detach the Terminal Angle (Bottom) 3. Remove the 2 lock screws and detach the Terminal Angle (Side) 4.

  • Page 22: Chapter 5. Adjustment

    LC-40/46LE810E (1st Edition) CHAPTER 5. LC-40LE810E ADJUSTMENT Service Manual [1] ADJUSTMENT PROCEDURE 1. Adjustment method after PWB and/or IC replacement due to repair The unit is set to the optimum at the time of shipment from the factory. If any value should become improper or any adjustment is necessary due to the part replacement, make an adjustment according to the following pro- cedure.
  • Page 23 LC-40/46LE810E (1st Edition) 2. Method of shuts down for Power supply Please execute the following procedures to shut down Power supply from the state of normal operation. 1) Keep touching the power supply key on the set for 5 seconds from the state of watching. * The screen disappears when power supply key is touched, but Keep pushing the power supply key.
  • Page 24 LC-40/46LE810E (1st Edition) 5. Description of display (1) Present page / number of total pages (4) Inducing display (3) Present colour system (2) Input that has been selected now (5) Inch setting and Model name display 1/21 INPUT1 AUTO EURO xxxxx MAIN Version 1.00 (E 2009/**/** )
  • Page 25 LC-40/46LE810E (1st Edition) 6. Adjustment process mode menu The character string in brackets [ ] will appear as a page title in the adjustment process menu header. Page Line Item Description Remarks (adjustment detail, etc.) 1/21 MAIN Version 1xxx (xxxxx) Main software version BOOT Version xxxxxxx...
  • Page 26 LC-40/46LE810E (1st Edition) Page Line Item Description Remarks (adjustment detail, etc.) 5/21 HDMI CEC TEST Enter HDMI CEC test INSPECT USB TERM Enter Reading inspection of USB memory terminal HDMI EDID WRITE Enter HDMI EDID WRITING MONIDATA READ [TEMP/OPC] MONITOR Temperature/OPC Acquisition tool. CAUSE RESET Enter Reset of standby cause...
  • Page 27 LC-40/46LE810E (1st Edition) Page Line Item Description Remarks (adjustment detail, etc.) 14/21 FRV-N Firmware Version xxxxx FRC-N Boot Script Version xxxxx FRC-N Device Version xxxxx TCON FPGA1 Serial Flash Version xxxxx TCON FPGA2 Serial Flash Version xxxxx TCON FPGA1 Config Rom Version xxxxx TCON FPGA2 Config Rom Version xxxxx...

  • Page 28: Special Features

    LC-40/46LE810E (1st Edition) Page Line Item Description Remarks (adjustment detail, etc.) 21/21 EEP SAVE Writing setting values to EEPROM. EEP RECOVER Reading setting values from EEPROM. MONITOR ERROR CAUSE RESET Reset of monitor error cause MODEL NAME LE705 MODEL NAME PANEL SIZE Panel size setting.

  • Page 29: Lamp Error Detection

    LC-40/46LE810E (1st Edition) 8. Lamp Error detection 1. Function This LCD colour TV set incorporates a Lamp error detection feature that automatically turns off the power for safety under abnormal lamp or lamp circuit conditions. If by any chance anything is wrong with the lamp or lamp circuit or if the lamp error detection feature is activated for some rea- son, the following will result.

  • Page 30: Public Mode

    LC-40/46LE810E (1st Edition) 9. Public Mode 1. Starting the Public Mode • There are two following ways to display the PUBLIC Mode setting screen. 1) Method of needing password a) Turn off the power, refer to “3. Method of shuts down for Power supply” b) While holding down the “INPUT”...
  • Page 31 LC-40/46LE810E (1st Edition) 4. Basic operation in the Public Mode Change or execution of the set value. Vol (+/-) or Cursor ( / ) Movement to the selected item. CH ( ) or Cursor ( / ) Decision (ok) Execution (Used by the items “Execution” and “RESET”.) Public Mode setting screen.
  • Page 32 LC-40/46LE810E (1st Edition) 2) Instantaneous current shutdown setting in turning off the power [SHUT DOWN MODE] Option “NORMAL” or “QUICK” Default NORMAL Function • This function decides whether scanning digital tuner is enabled or disabled when the power is standby. NORMAL : Scanning digital tuner is enabled when the power is standby.
  • Page 33 LC-40/46LE810E (1st Edition) 7) Main Unit Operation [PANEL BUTTON] Option “RESPOND” or “NORESPOND” (loop enabled) Default “RESPOND” Function • RESPOND : The main unit’s keys are enabled. • NO RESPOND : The main unit’s keys are disabled excluding the POWER key (RECEPTION/STANDBY key).
  • Page 34 LC-40/46LE810E (1st Edition) 10)OSD display [ON SCREEN DISPLAY] Option “YES”, “NO” or “LIMITED” (loop enabled) “LIMITED” is looped only in case of need (destination). Default “YES” Function • : OSD is displayed • : the following OSD is not displayed. Registration, setting, adjustment menu, channel call, volume bar, and input select •...
  • Page 35 LC-40/46LE810E (1st Edition) 13)Speaker ON/OFF selection [LOUD SPEAKER] Option “ON” or “OFF” (loop enabled) Default Function : The sound from the speakers is output. : The sound from the speakers is not output even if the headphones are not used. Remarks •...
  • Page 36 LC-40/46LE810E (1st Edition) 10.2. PAL signal adjustment Adjustment point Adjustment conditions Adjustment procedure Setting [Signal] • Feed the PAL full field colour bar signal (75% colour saturation) to EXT1 SCART IN. Full field colour bar composite [VIDEO input signal] signal [Terminal] EXT1 SCART IN 100% white...
  • Page 37 LC-40/46LE810E (1st Edition) 10.5. ADC adjustment (Component 15K) Adjustment point Adjustment conditions Adjustment procedure Setting [Signal] • Feed the COMPONENT 15K 100% full field colour bar signal (100% COMP15K, 50Hz colour saturation) to EXT3 COMPONENT IN. 100% Full field colour bar Signal [Terminal] EXT3 COMPONENT IN 100% white...

  • Page 38: White Balance Adjustment

    LC-40/46LE810E (1st Edition) 11. White Balance Adjustment For white balance adjustment, adjust the offset values on pages 11/21. [Condition of the unit for inspection] : Modulated light (+16), Colour temperature (High) AV MODE: DYNAMIC Active Backlight: OFF OPC: OFF Asing Time: Min,60 minute [Input signal condition] : HDMI 1080i 15IRE (LO), 78IRE (HI) [Adjustment reference device]...

  • Page 39: Initialization To Factory Settings

    LC-40/46LE810E (1st Edition) 13. Initialization to factory settings CAUTION: When the factory settings have been made, all user setting data, including the channel settings, are initialized. (The adjustments done in the adjustment process mode are not initialized.) Keep this in mind when initializing these settings. Adjustment point Adjustment conditions Adjustment procedure...
  • Page 40 LC-40/46LE810E (1st Edition) 6. The caution for update showes up. • The picture will temporary go dark until the software update display apeeares • Wait several minutes and don't unplug the AC cord Select OK when if there is no problem. 7.

  • Page 41: Chapter 6. Troubleshooting Table Troubleshooting Table

    LC-40/46LE810E (1st Edition) CHAPTER 6. LC-40LE810E TROUBLESHOOTING TABLE Service Manual [1] TROUBLESHOOTING TABLE No power (Central Icon LED failure to light up) or No startup (Central Icon LED is flashing) Is the AC cord connector tightly connected to the set? Reconnect the AC cord tightly and turn on the power again.
  • Page 42 LC-40/46LE810E (1st Edition) The sound is not emitted from the Speaker & Woofer though the picture has come out. No sound output in all modes? Is the signal output from pins (F30/AOLRCK), (F28/AOBCK) Check IC3302 and its peripheral circuits. (G28/AOSDATA0) of IC3302 (Digital AV decode & Main CPU)? Is the signal sent to pins (7), (8), (9) of IC2701 (DSP)? Check the line between IC3302 and IC2701.
  • Page 43 LC-40/46LE810E (1st Edition) No sound (during the reception of TV (ANALOG) broadcasting) Does not the sound go out though the picture has come out when UHF/VHF is received? Is a SIF signal output from pin (13) of TUNER (TU1101)? Check the tuner and its peripheral circuits. Replace as required.
  • Page 44 LC-40/46LE810E (1st Edition) No sound from external input devices (1) Does not the sound of the audio signal input to EXT1 go out? Is there a audio input signal to pins (19/AUDIO_IN_L) and (21/ Check the setting of an external input device that connects with AUDIO_IN_R) of EXT1 (SC505)? EXT1.
  • Page 45 LC-40/46LE810E (1st Edition) No sound from external input devices (4) Does not the sound of the audio signal input to HDMI1/2/3/4 go out? Please Refer to “[External input HDMI-1/2/3/4] No picture on the display (10)”. No sound from external output device (1) No audio signal output to EXT1 terminal.
  • Page 46 LC-40/46LE810E (1st Edition) No sound from external output device (3) No sound from DIGITAL AUDIO OUTPUT terminal. Is the audio signal output to pins (1) of sound output terminal Check D520 and peripheral circuits. (D520)? Is SPDIF_MUTE signal SPDIF_MUTE [H29/IC3302] or Check the peripheral circuits of IC3302 and SPDIF_MUTE.
  • Page 47 LC-40/46LE810E (1st Edition) No picture on the display (1) The picture doesn't appear in all modes. Is the LVDS signal output from IC3302 (DIGITAL_AV_DECODER_&_MAIN_CPU_&_VIDEO PROCESSER) respectively? LVDS0_D0N/P (D14/C14), LVDS0_D1N/P (D15/C15), LVDS0_D2N/P (D16/C16), LVDS0_CLKN/P_83MHz (D17/C17), LVDS0_D3N/P (D18/C18), LVDS0_D4N/P (D19/C19), LVDS1_D0N/P (B14/A14), LVDS1_D1N/P (B15/A15), LVDS1_D2N/P (B16/A16), LVDS1_CLKN/P_83MHz (B17/A17), LVDS1_D3N/P (B18/A18), LVDS1_D4N/P (B19/A19) Check IC3302 and its peripheral control circuits.
  • Page 48 LC-40/46LE810E (1st Edition) [External input EXT1] No picture on the display (4) Does not the picture of the CVBS signal input to EXT1 go out? Is CVBS signal sent to pin (14) of EXT1 (SC505)? Check the setting of an external input device that connects with EXT1.
  • Page 49 LC-40/46LE810E (1st Edition) [External input EXT2] No picture on the display (7) Does not the picture of the CVBS signal input to EXT2 go out? Is a CVBS signal input to pin (3) of EXT8 (J505)? Check the setting of an external input device that connects with EXT2.
  • Page 50 LC-40/46LE810E (1st Edition) [External input HDMI-1/2/3/4] No picture on the display (10) Does not the picture/sound of the HDMI signal input to HDMI-1/2/3/4 go out? Is the Hot plug detection function output from pin (19) of the Check the line between SC1503 and pin (45) of IC1504 (HDMI- HDMI-1 (SC1503) normal? SW).
  • Page 51 LC-40/46LE810E (1st Edition) <During external connection> No picture on the monitor No picture appears on EXT1connected monitor during the ATV/DTV reception. Is CVBS signal output into pin (2) of EXT1 (SC505)? Check the setting of an external input device that connects with EXT1.
  • Page 52 LC-40/46LE810E (1st Edition) No light (Back Light doesn't light) Is the AC cord connector tightly connected to the set? Reconnect the AC cord tightly and turn on the power again. Are the wire harnesses and other cables properly connected in Reconnect the wire harnesses and other cables properly in the the set? set.

  • Page 53: Led Flashing Specification At The Time Of The Error

    LC-40/46LE810E (1st Edition) [2] LED flashing specification at the time of the error Display method • Refer to Table 1. • LED that can be used is only one of the central icons. This expresses the error situation by combining blinking at low speed and blinking at high speed. •...
  • Page 54 LC-40/46LE810E (1st Edition) Table 1. Concrete flashing pattern Expression for a rough content Expression for Details Item low-speed high-speed low-speed high-speed Cause blinking blinking blinking blinking Lamp system failure Flashes once — Flashes once Flashes once Lamp error Power PWB failure Flashes twice —...
  • Page 55 LC-40/46LE810E (1st Edition) LED flashing timing chart at the time of the error 100ms 400ms 1.6sec 1) Low-speed blinking Error type Expression of Central Icon LED Note: Pins are monitor microprocessor pins (IC2002). Lamp failure H: ON Refer to “Lamp failure details”. low-speed blinking LOW/High blinking by pressing the [MENU] key on the remote Flashes once...
  • Page 56 LC-40/46LE810E (1st Edition) 4) Communication failure details (Low-speed blinking: Flashes 3 times + High-speed blinking) Error type Expression of Central Icon LED Note: Basically, debug print logs are analyzed or communication logs are analyzed by a bus monitor. Initial communication H: ON Initial communication from the main CPU is not received.

  • Page 57: Chapter 7. Major Ic Informations

    LC-40/46LE810E (1st Edition) CHAPTER 7. LC-40LE810E MAJOR IC INFORMATIONS Service Manual [1] MAJOR IC INFORMATIONS REF NO Name Part Code Description [MAIN UNIT] IC8401 RH-iXC147WJQZQ Flash This IC is 512MB NAND flash memory. This IC stores the software data that processes the system of TV such as the graphic processing, the LCD controls, and backlights etc.
  • Page 58 LC-40/46LE810E (1st Edition) — M E M O — 7 – 2...

  • Page 59: Chapter 8. Overall Wiring/Block Diagram Overall Wiring Diagram (Lc-40Le810E)

    LC-40/46LE810E (1st Edition) LC-40LE810E CHAPTER 8. OVERALL WIRING/BLOCK DIAGRAM Service Manual [1] OVERALL WIRING DIAGRAM (LC-40LE810E) OVERALL WIRING DIAGRAM (LC-40LE810E) LED UNIT [L1] Woofer [L2] [SB] QCNW-K553WJQZ POWER Unit P2702 [LB] [LB] P9602 J3301 QCNW-K552WJQZ [PD] J9501 [PD] P9601 QCNW-K548WJQZ...

  • Page 60: Overall Wiring Diagram (Lc-46Le810E)

    LC-40/46LE810E (1st Edition) [2] OVERALL WIRING DIAGRAM (LC-46LE810E) OVERALL WIRING DIAGRAM (LC-46LE810E) LED UNIT QCNW-K570WJQZ Woofer [L1] [L2] POWER Unit [SB] P2702 [LB] [LB] P9602 J3301 QCNW-K978WJQZ [PD] J9501 P9601 QCNW-K976WJQZ [AS] [PD] MAIN Unit Audio out J504 AV-IN [SP] J505 P2701 20 19...

  • Page 61: System Block Diagram

    LC-40/46LE810E (1st Edition) [3] SYSTEM BLOCK DIAGRAM SYSTEM BLOCK DIAGRAM CVBS MAIN CVBS/LR EXT2 CVBS_L/R CVBS [LW] CVBS/LR P2601 (41p ) S-Video EXT1 (SCART1) TUNER CVBS OUT IC504 TUNER_OUT TUNER OUT LR_OUT TUNER OUT L/R MM1506XN Mute FS/FB From CPU or UCON FAST_SW SLOW SW TU_CVBS_OUT_MUTE...
  • Page 62 LC-40/46LE810E (1st Edition) — M E M O — 8 – 4...

  • Page 63: Parts Guide

    PACKING PARTS ASSEMBLIES (NOT REPLACEMENT ITEM) (LC-40LE810E) LCD PANEL MODULE PACKING PARTS (NOT REPLACEMENT ITEM) CABINET PARTS (LC-40LE810E) (LC-46LE810E) CABINET PARTS (LC-46LE810E) SERVICE JIGS (USE FOR SERVICING) SUPPLIED ACCESSORIES Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
  • Page 64 LCD CONTROL Unit (LC-40LE810E) RUNTK4512TPZC LCD CONTROL Unit (LC-46LE810E) RUNTK4437TPZE LED PWB Unit, x4 (LC-40LE810E) RUNTK4462TPZZ LED PWB Unit, x4 (LC-46LE810E) RUNTK4461TPZZ [2] LCD PANEL MODULE R1LK400D3LWF2Y 40" LCD Panel Module Unit (LC-40LE810E) R1LK460D3LWA2Y 46" LCD Panel Module Unit (LC-46LE810E)
  • Page 65 LC-40/46LE810E (1st Edition) [3] CABINET PARTS (LC-40LE810E) ICON Unit TOUCH SENSOR R/C, Unit LED Unit MAIN POWER Unit Unit 40" LCD Panel Module Unit X3-3 2-10 X1-2 X3-1 X3-2 X1-1...
  • Page 66 LC-40/46LE810E (1st Edition) PRICE PART PARTS CODE DESCRIPTION RANK MARK DELIVERY [3] CABINET PARTS (LC-40LE810E) Front Cabinet Ass'y CCABAC527WJ11 R/C Decoration Cover HDECQB442WJ1A Rear Cabinet Ass'y CCABBB698WJ12 Rear Cabinet GCABBB698WJSA Terminal Label (Side) HiNDPD726WJSA Terminal Label (Bottom) HiNDPD711WJSA Himeron PSPAHC152WJ1Z...
  • Page 67 LC-40/46LE810E (1st Edition) [4] CABINET PARTS (LC-46LE810E) ICON Unit POWER Unit TOUCH SENSOR R/C, Unit LED Unit MAIN Unit 46 46 46" LCD Panel Module Unit 2-10 X3-3 X3-1 X3-2 X1-1 X1-1...
  • Page 68 LC-40/46LE810E (1st Edition) PRICE PART PARTS CODE DESCRIPTION RANK MARK DELIVERY [4] CABINET PARTS (LC-46LE810E) Front Cabinet Ass'y CCABAC528WJ11 R/C Decoration Cover HDECQB442WJ1A Rear Cabinet Ass'y CCABBB699WE12 Rear Cabinet GCABBB699WJSA Terminal Label (Side) HiNDPD726WJSA Terminal Label (Bottom) HiNDPD711WJSA Himeron PSPAHC152WJ1Z Spacer PSPAZC461WJZZ Insulation Sheet...
  • Page 69 X3-1 X3-2 X3-3 PRICE PART PARTS CODE DESCRIPTION RANK MARK DELIVERY [5] SUPPLIED ACCESSORIES Stand Support Ass'y (LC-40LE810E) CANGKC707WJ01 Stand Support Ass'y (LC-46LE810E) CANGKC708WJ01 X1-1 Support Plate A (LC-40LE810E) CANGKC707WJ03 X1-1 Support Plate A (LC-46LE810E) CANGKC708WJ03 X1-1-1 Support Plate (LC-40LE810E)
  • Page 70 X2-6 Screw, x5 (LC-46LE810E) LX-BZA368WJF7 X2-7 Hinge (LC-40LE810E) MHNG-A237WJZZ X2-7 Hinge (LC-46LE810E) MHNG-A238WJZZ X2-8 Leg Cushion (18x5), x4 (LC-40LE810E) PSPAZC326WJZZ X2-8 Leg Cushion (18x5), x6 (LC-46LE810E) PSPAZC326WJZZ X2-9 PSPAZC333WJZZ Leg Cushion (10x25x2), x4 (LC-40LE810E) X2-9 Leg Cushion (10x25x2), x6 (LC-46LE810E)
  • Page 71 LC-40/46LE810E (1st Edition) [6] PACKING PARTS (NOT REPLACEMENT ITEM) (LC-40LE810E)
  • Page 72 LC-40/46LE810E (1st Edition) PRICE PART PARTS CODE DESCRIPTION RANK MARK DELIVERY [6] PACKING PARTS (NOT REPLACEMENT ITEM) (LC-40LE810E) Packing Case SPAKCF674WJZZ Wrapping Paper SPAKPB475WJZZ Wrapping Paper, x2 SPAKPB526WJZZ Wrapping Paper SPAKPB528WJZZ Packing Add. (Top) SPAKXC920WJZZ Packing Add. (Bottom) SPAKXC925WJZZ Polyethylene Bag...
  • Page 73 LC-40/46LE810E (1st Edition) [7] PACKING PARTS (NOT REPLACEMENT ITEM) (LC-46LE810E)
  • Page 74 LC-40/46LE810E (1st Edition) PRICE PART PARTS CODE DESCRIPTION RANK MARK DELIVERY [7] PACKING PARTS (NOT REPLACEMENT ITEM) (LC-46LE810E) Packing Case (Top) SPAKCF675WJZZ Packing Case (Bottom) SPAKCF496WJZZ Wrapping Paper SPAKPB477WJZZ Wrapping Paper, x2 SPAKPB527WJZZ Wrapping Paper SPAKPB529WJZZ Packing Add. (Top) SPAKXC921WJZZ Packing Add.
  • Page 75 LC-40/46LE810E (1st Edition)
  • Page 76 LC-40/46LE810E (1st Edition) COPYRIGHT © 2010 BY SHARP CORPORATION ALL RIGHTS RESERVED. No Part of this publication may be reproduced, stored in a retrieval system, or transmitted in any from or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

This manual is also suitable for:

Lc-46le810e

Table of Contents

Save PDF