CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
Page 4
Ver. 1.0 are shown in blue. 1-5. METHOD OF EXCHANGING SI SCREEN AND FOCUSING SCREEN The focusing screen of the DSLR-A700 is available with two types, standard and M type. If the type was changed due to the replacement of focusing screen, the setting must be changed according to the type.
Page 5
ENGLISH JAPANESE ENGLISH JAPANESE 1. SERVICE NOTE DSLR-A700_L2...
Page 6
ENGLISH JAPANESE ENGLISH JAPANESE DSLR-A700_L2...
Page 7
Ver. 1.1 2007.10 ENGLISH JAPANESE ENGLISH JAPANESE DSLR-A700_L2 1-5E...
2. DISASSEMBLY NOTE FOR REPAIR • Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Cut and remove the part of gilt Do not insert the cable insufficiently nor crookedly. which comes off at the point. (Be careful or some •...
HELP HELP 2-2. DISASSEMBLY EXPLODED VIEW HARDWARE LIST 2-2-1. OVERALL SECTION-1 Follow the disassembly in the numerical order given. 1 Rear Cover (1-1 to 1-8) 2 Side Cover (2-1 to 2-2) 1 Rear Cover (See Page 2-4) 1-7 (#94) 1-5 (#12) Overall Section-2 (See Page 2-5) 1-6 (#12)
2-2-2. REAR COVER SECTION EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 IO-081 Board (1-1 to 1-8) 2 Control Switch Block (JY62300) (2-1 to 2-6) Note: On installation of the diopter adjust dial, adjust the position of lever of JY62300 and the metering mode lever.
2-2-3. OVERALL SECTION-2 EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Front Cover (1-1 to 1-6) 2 Top Cover (2-1 to 2-9) Note: On installation of the diopter adjust dial, match the position of the convex part in two places. Diopter Adjust Dial (Back Side) Note: High-voltage cautions...
2-2-4. FRONT COVER SECTION EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Control Switch Block (FS62300) (1-1 to 1-6) 1 Control Switch Block (FS62300) HELP 5 1-3 (#5) 1-4 (#94) HELP 5 (#94) Note: On installation of the diopter adjust dial, adjust the position of lever of FS62300 and the focus mode lever.
2-2-5. TOP COVER SECTION-1 EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Control Switch Block (RL62300) (1-1 to 1-7) 2 Control Switch Block (TK62300) (2-1 to 2-4) 3 Control Switch Block (MD62300) (3-1 to 3-4) Note: On installation of the mode dial, set "M"...
Page 15
2-2-6. TOP COVER SECTION-2 EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Flash Unit (1-1 to 1-5) 2 TOP-003 Flexible Board (2-1 to 2-7) 1 Flash Unit HELP 9 1-4 (#12) HELP 8 HELP 7 (Solder) HELP 6 2-3 (#10)
2-2-7. HALF BODY SECTION (AM BOARD) EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 AM-012 Board (1-1 to 1-27) 1-3 (#94) HELP 12 Half Body Section 1-4 (#12) 1 AM-012 Board (#12) (MA Flexible Board) (See Page 2-10) 1-25 (Open) Note: When media lid is shut, the switch...
2-2-8. HALF BODY SECTION EXPLODED VIEW HARDWARE LIST (MA FLEXIBLE BOARD) Follow the disassembly in the numerical order given. 1 MA-448 Flexible Board (1-1 to 1-17) HELP 15 HELP 15 HELP 16 1 MA-448 Flexible Board HELP 18 1-17 (#12) 1-12 Half Body Section (DD Board) (See Page 2-11)
2-2-9. HALF BODY SECTION (DD BOARD) EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Eye Piece Frame Unit (1-1 to 1-2) 2 AF Assist Light Block (2-1) 3 DD-280 Board (3-1 to 3-4) 3-2 (#85) 3-3 (#5) 3 DD-280 Board 2-1 (#12)
2-2-11. HALF BODY SECTION (BT HOLDER) EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Battery Holder (1-1) 2 Tebure Unit (2-1 to 2-5) 3 Shutter (3-1) HELP 22 1 Battery Holder 2 Tebure Unit Refer to page 2-18 "2-3. IMAGER INCLINATION ADJUSTMENT"...
Page 21
2-2-12. HALF BODY SECTION (AF MODULE) EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 AF Module (1-1 to 1-3) 2 Front Frame (2-1 to 2-3) 3 Jack Holder (3-1 to 3-6) 2-1 (#5) Mirror Box Section 2-3 (#12) (Penta Unit) (See Page 2-15)
Page 22
2-2-13. MIRROR BOX SECTION (PENTA UNIT) EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Penta Unit (1-1 to 1-3) 1 Penta Unit 1-3 (#74) Refer to page 1-2 "1-5. METHOD OF EXCHANGING SI SCREEN AND FOCUSING SCREEN"...
2-2-14. MIRROR BOX SECTION (SUB UNIT-1) EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Iris Ring (1-1 to 1-9) 2 Aperture Unit (2-1 to 2-5) 3 AF Driving Unit (3-1 to 3-9) 2 Aperture Unit Refer to page 2-20 "2-6.
2-2-15. MIRROR BOX SECTION (SUB UNIT-2) EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 Charge Base Plate A Unit (1-1 to 1-11) 2 Shutter Charge Lever (2-1 to 2-12) 2-12 Refer to page 2-22 "2-9. LEVERS AND GEARS INSTALLATION"...
Page 25
2-3. IMAGER INCLINATION ADJUSTMENT Checking Method Use the copy stand or place a mirror on the wall, and adjust the accuracy so that the camera is opposed to the mirror. Use the AE master lens as an inspection lens. Obtain the inclination angle with the Photoshop, and perform as follows according to the angle: •...
Page 26
2-4. SHUTTER INSTALLATION Follow the assembly in the numerical order given. 1 Shutter Shock Absorbing Ring Shutter 2 Raise Main Mirror up. Mirror Charge Lever Up 3 Rotate Idle Gear Don't damage Idle Gear. Shutter Charge Lever Down Boss 4 Shutter 5 Shutter Flexible Board DSLR-A700_L2 2-19...
Page 27
2-5. IRIS RING REMOVAL/INSTALLATION Removal Rotate the iris ring clockwise, and remove it at the stop position (iris-in end). At this time, do not rotate the iris joint gear of the Aperture Unit. Installation With the Aperture Unit set in the charge position (see "2-7. Aperture Unit Charge Position Setting" ), install it on the front frame set.
Page 28
2-8. APERTURE UNIT FREE POSITION SETTING Set the Aperture Unit to a free position once, if the gear was rotated accidentally and the charge position is disordered, or if the charge position was shifted during disassembly. In a free state, the edge of this spring In a free state, a hole in the gear almost will move up and down about 1 mm if coincides with a hole in the Aperture Unit.
Page 29
2-9. LEVER AND GEARS INSTALLATION Follow the assembly in the numerical order given. 2-9-1. MIRROR CHARGE/SHUTTER CHARGE LEVERS INSTALLATION - Levers Position - 1 Mirror Charge Lever Assy Mirror Charge Lever Assy 4 Screw (#93) 3 Charge Base Plate C Assy Main Mirror Holder Boss 2 Shutter Charge...
Page 30
2-9-3. CHARGE BASE PLATE B INSTALLATION 1 Charge Base Plate B Assy 2 Screw (#93) Hole Hole 2-9-4. MIRROR DRIVING (SP) INSTALLATION 3 Screw (#93) - Spring Position - 2 Mirror Driving (SP) Retainer Mirror Charge Cam Gear 1 Mirror Driving (SP) Mirror Driving (SP) DSLR-A700_L2...
Page 31
2-10.GREASE APPLICATION AREA Grease uses G-85 (J-6082-626-A). Ring (SP) Ring Roller (C) Shaft Grease Grease Shutter Cam Gear Assy Mirror Charge Cam Gear Grease Grease Front Frame Assy Grease Grease Grease Grease Grease DSLR-A700_L2 2-24...
Page 32
2-11.CLEANING PROCEDURE OF OLPF <Preparation> Make it to Cleaning Mode of Power On/Set Up Menu by using the AC power supply. (It comes to Mirror Up/Shutter Open) Note: Use the AC power supply absolutely. <Cleaning Method> Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
Page 33
HELP Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown. HELP 1: HELP 3: IO Guard Sheet LCD/Back Light/CD Insulating Sheet IO-081 Board - Side B - - Side A - LCD Flexible Board Solder CD Insulating Sheet Back Light Flexible Board HELP 4: MC Insulating Sheet...
Page 34
HELP 5: HELP 8: Tape (ASCD) Tape (ASCD) Tape (ASCD) Boss Tape (ASCD) Tape (ASCD) Tape (ASCD) Tape (ASCD) HELP 6: Tape (ASCD)/TK62300/RL Fixed Tape Tape (ASCD) Flash Boss Harness RL Fixed Tape HELP 9: Flash Unit Guide Flash Harness Flash Unit TK62300 Tape (ASCD)
Page 35
HELP 11: HELP 13: TOP-003 Flexible Board Tape (ASCD)/Motor Harness Motor Harness TOP-003 Flexible Board Tape (ASCD) HELP 12: HELP 14: Label (AM) Shutter Flexible Holder - Bottom View - Shutter Flexible Holder - Rear View - Label (AM) Bottom Frame Shutter Flexible Holder DSLR-A700_L2 HELP...
Page 36
HELP 15: Tape (ASCD)/DC Harness GP-021 Flexible Board Tape (ASCD) DC Harness Tape (ASCD) HELP 16: HELP 18: PT Insulating Sheet MA-448 Flexible Board PT Insulating Sheet MA-448 Flexible Board HELP 17: HELP 19: GY-003 Flexible Board Bottom Frame IFL Flexible Board GY-003 Flexible Board Bottom Frame DD Plate...
Page 37
HELP 20: HELP 23: MMGND Plate A Battery Lid (SP) MMGND Plate A Boss Boss Battery Lid (SP) HELP 21: RM Guard Sheet RM Guard Sheet HELP 24: CDGND Plate A/B Boss Boss CDGND Plate A CDGND Plate B HELP 25: IS Flexible Unit IS Flexible Unit HELP 22:...
Page 38
HELP 26: HELP 29: RM-095 Flexible Board Coupler Lever Tension SP DC Jack Harness Coupler Lever Tension SP RM-095 Flexible Board Coupler Joint Lever DC Jack Harness HELP 27: Penta Unit HELP 30: AF Driving Unit Flexible Borad Boss AF Driving Unit Flexible Borad Charge Base Plate B Unit Flexible Borad...
3. BLOCK DIAGRAMS Link Link OVERALL BLOCK DIAGRAM (1/6) POWER BLOCK DIAGRAM (1/6) OVERALL BLOCK DIAGRAM (2/6) POWER BLOCK DIAGRAM (2/6) OVERALL BLOCK DIAGRAM (3/6) POWER BLOCK DIAGRAM (3/6) OVERALL BLOCK DIAGRAM (4/6) POWER BLOCK DIAGRAM (4/6) OVERALL BLOCK DIAGRAM (5/6) POWER BLOCK DIAGRAM (5/6) POWER BLOCK DIAGRAM (6/6) OVERALL BLOCK DIAGRAM (6/6)
Page 40
3. BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM (1/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. IS-017 BOARD IS-016 AM-012 BOARD (1/6) FP-695 IO-081 FLEXIBLE FLEXIBLE BOARD BOARD BOARD (1/2) CN4002...
Page 41
3-2. OVERALL BLOCK DIAGRAM (2/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-012 BOARD (2/6) CN2802 HDMI_DY[0-7] TX0± - TX2± HDMI_DUV[0-7] IC2401 HDMI HDMI_DE TRANSMITTER HDMI_CLK TXC± HDMI (11/22) XHDMI_HD...
Page 42
3-3. OVERALL BLOCK DIAGRAM (3/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-012 BOARD (3/6) XSHUTTER_X_SW STAR_SI_CA, STAR_SO_CA, STAR_SCK_CA, STAR_CS_CA GY-003 FLEXIBLE Q3404 SH_2C 2ND_CURTAIN_MG BOARD OVERALL (1/6) SHUTTER SH_1C 1ST_CURTAIN_MG...
Page 43
3-4. OVERALL BLOCK DIAGRAM (4/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AF-110 AM-012 BOARD (4/6) FLEXIBLE MA-448 AE-029 FLEXIBLE EYE-003 BOARD FLEXIBLE BOARD FLEXIBLE CN3511 BOARD BOARD Vout AFCCD_VOUT...
Page 44
3-5. OVERALL BLOCK DIAGRAM (5/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-012 BOARD (5/6) TOP-003 FLEXIBLE BOARD Q3511 CN3516 BZ901 BUZZER_A BUZZER BUZZER BUZZER (BUZZER) DRIVE S5501 xINT_FLASH_UP_SENSE XINT_FLASH_UP_SENSE...
Page 45
3-6. OVERALL BLOCK DIAGRAM (6/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. ST-173 BOARD T6501, T6502 D6501, CN6503 D6503 D6502 UNREG_FLASH XE_K AM-012 BOARD (6/6) MA-448 FLEXIBLE C901 BOARD (2/2) FLASH...
Page 46
3-7. POWER BLOCK DIAGRAM (1/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. DD-280 BOARD J902 DC IN CN0513 CN0501 F0501 ACV_UNREG UNREG_LVDD0 BATT/XEXT POWER (4/6) (PAGE 3-10) D0506 VCC1C_DD D0505...
Page 47
3-8. POWER BLOCK DIAGRAM (2/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-012 BOARD (1/5) CN3502 IC3401 F3401 UNREG UNREG CHARGE MOTOR DRIVE (14/22) IMG_1.8V_SLVDS 2 PWM IMG_3.3V POWER (6/6) Q3507, Q3508,...
Page 48
3-9. POWER BLOCK DIAGRAM (3/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-012 BOARD (2/5) EVER_3.3V EVER_3.3V EVER_3.3V IC3801 IC_3001_3.3V IC_3001_3.3V IC_3001_3.3V ANTI-SHAKE Q3801, Q3802 DRIVE AS_7.7V AS_7.7V LIMITER (PITCH)
Page 49
3-10. POWER BLOCK DIAGRAM (4/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. ST-173 BOARD T6501, CN6501 T6502 D6501, CN6503 UNREG_FLASH D6503 D6502 XE_K POWER (1/6) C901 (PAGE 3-7) CHARGING FLASH CAPACITOR...
Page 50
3-11. POWER BLOCK DIAGRAM (5/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-012 BOARD (4/5) FP-695 FLEXIBLE IO-081 BOARD BOARD CN5352 CN3518 CN5301 IMG_3.3V IMG_3.3V LCD901 IMG_1.8V_4S IMG_1.8V_4S VDDIO 3 inch...
Page 51
3-12. POWER BLOCK DIAGRAM (6/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. AM-012 BOARD (5/5) IS-015 FLEXIBLE IS-017 BOARD IC4002 BOARD 4.5V REG CN2601 CN4001 IC_3001_6.0V VDDCM (A4.5V) 1 Vin Vout 3 CE...
Page 52
Ver. 1.1 2007.10 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAMS FRAME SCHEMATIC DIAGRAM (1/2) To MA-448 Flexible Board CN5906 (through the Flexible Flat Cable (ST-174)) (Page 4-2) HARNESS (MO-001) BT902 BATTERY TERMINAL – J902 OMEGA UNIT IS FLEXIBLE UNIT DC IN CN6502...
Page 55
4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For schematic diagrams) Precautions for Replacement of Imager • All capacitors are in µF unless otherwise noted. pF : µ •...
Page 70
Note:D901 and AFL-001 flexible board are not supplied, but they are included in AF assist light block assy. EYE_LED_A EYE_LED_A LND011 pin6 LND006 EYE_LED_A EYE_LED_K EYE_LED_K LND012 pin5 LND005 EYE_LED_K REG_GND_2 EYEPIECE LND004 REG_GND REG_GND LND015 SENSORS EYE_SPC_A LND013 LND003 EYE_SPC_A EYE_SPC_A EYE_SPC_K...
Page 72
• Refer to page 4-3 for mark 0. CL6502 CL6501 FLASH UNIT(FL62300) is replaced as block, so that there PRINTED WIRING BOARD and SCHEMATIC DIAGRAM are omitted. CN6501 PGND UNREG_FLASH T6502 D6501 FV02R80TP CL6505 D6502 DD-280 T6501 D6503 RR264M-400 CN6503 FV02R80TP (1/2) XE_K...
Page 73
BZ901 (BUZZER) Note:BZ901 is not included in TOP-003 flexible complete board. D5501 RB48SKTK CN5501 CONTROL xMODE_DIAL_C SWITCH xMODE_DIAL_COM BLOCK BUZZER LND031 pin1 LND001 BUZZER BUZZER_A D5502 RB48SKTK xMODE_DIAL_D (MD62300) LND032 IMG_5.0V LND001-LND006 pin2 LND002 IMG_5.0V BUZZER_B xMODE_DIAL_A EXT_FLASH_TRIGGER Page 4-50 LND003 EXT_FLASH_TRIGGER xMODE_DIAL_B...
4-3. PRINTED WIRING BOARDS Link Link IS-017 BOARD MA-448 FLEXIBLE BOARD RM-095 FLEXIBLE BOARD IO-081 BOARD ST-173 BOARD MM-067 BOARD GY-003 FLEXIBLE BOARD TOP-003 FLEXIBLE BOARD COMMON NOTE FOR PRINTED WIRING BOARDS DSLR-A700_L2...
Page 81
4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS • : Uses unleaded solder. • Chip parts. • : Circuit board Transistor Diode : Flexible board Pattern from the side which enables seeing. : pattern of the rear side (The other layers’...
NOTE 5. REPAIR PARTS LIST NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown. EXPLODED VIEWS EXPLODED VIEWS Link Link OVERALL SECTION-1 REAR COVER SECTION OVERALL SECTION-2 FRONT COVER SECTION HALF BODY SECTION HALF BODY SECTION...
Page 91
Ver. 1.3 2008.08 The changed portions from 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST Ver. 1.2 are shown in blue. 5. REPAIR PARTS LIST NOTE: • -XX, -X mean standardized parts, so they may have some differences from When indicating parts by reference number, the original one.
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1. EXPLODED VIEWS 5-1-1. OVERALL SECTION-1 ns: not supplied Rear Cover Section (See page 5-3) Overall Section-2 (See page 5-4) Ref. No. Part No. Description Ref. No. Part No. Description 2-894-387-01 SEAL, BODY CAP 3-269-761-01 COVER, SOKKAN...
Page 93
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-2. REAR COVER SECTION ns: not supplied (15mm x 15mm) LCD901 BL901 CAUTION: For the part of 53, cut SHEET, INSULATING, CD (3-091- 260-01) into the desired length and use it. Ref.
Page 94
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-3. OVERALL SECTION-2 ns: not supplied Top Cover Section-1 (See page 5-6) Half Body Section (AM Board) (See page 5-8) Front Cover Section (See page 5-5) Ref. No. Part No. Description Ref.
Page 95
Ver. 1.1 2007.10 The changed portions from 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST Ver. 1.0 are shown in blue. DISASSEMBLY HARDWARE LIST 5-1-4. FRONT COVER SECTION ns: not supplied SE901 Ref. No. Part No. Description Ref. No. Part No. Description X-2179-797-1 GRIP ASSY 1-480-182-11 SWITCH BLOCK, CONTROL (FS62300)
Page 96
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-5. TOP COVER SECTION-1 ns: not supplied Top Cover Section-2 (See page 5-7) Ref. No. Part No. Description Ref. No. Part No. Description A-1318-417-A COVER BLOCK ASSY, TOP 1-480-184-11 SWITCH BLOCK, CONTROL (MD62300) 1-480-185-11 SWITCH BLOCK, CONTROL (TK62300) 3-080-204-01 SCREW, TAPPING, P2 (Black) 3-274-513-01 TAPE (ASCD)
Page 97
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-6. TOP COVER SECTION-2 ns: not supplied White (Note) Black (Note) Pink (Note) BZ901 Note: About the arrangement of harness, re- fer to HELP 4. • Refer to page 5-1 for mark 0. Ref.
Page 98
Ver. 1.1 2007.10 The changed portions from 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST Ver. 1.0 are shown in blue. DISASSEMBLY HARDWARE LIST 5-1-7. HALF BODY SECTION (AM BOARD) ns: not supplied BT901 (Note) Half Body Section (MA Flexible Board) (See page 5-9) BH3001 (Note)
Page 99
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-8. HALF BODY SECTION (MA FLEXIBLE BOARD) Half Body Section (DD Board) (See page 5-10) Ref. No. Part No. Description Ref. No. Part No. Description 1-872-890-11 FLEXIBLE FLAT CABLE (ST-174) A-1317-979-A MA-448 FLEXIBLE BOARD, COMPLETE * 352 3-274-792-01 SHEET, PT INSULATING...
Page 100
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-9. HALF BODY SECTION (DD BOARD) #85 #5 (including AFL-001 flexible board) (including EYE-003 flexible board) Half Body Section (ST/MM Board) (See page 5-11) Ref. No. Part No. Description Ref.
Page 101
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-10. HALF BODY SECTION (ST/MM BOARD) ns: not supplied - 0 6 C901 Half Body Section (BT Holder) (See page 5-12) • Refer to page 5-1 for mark 0. Ref.
Page 102
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-11. HALF BODY SECTION (BT HOLDER) ns: not supplied BT902 Tebure Unit Section (See page 5-13) Half Body Section (AF Module) (See page 5-14) • Refer to page 5-1 for mark 0. Ref.
Page 103
Ver. 1.4 2008.10 The changed portions from 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST Ver. 1.3 are shown in blue. HARDWARE LIST 5-1-12. TEBURE UNIT SECTION (including IC4004 (CMOS imager) and IS-017 board) (Note 1, 2) (including IS-015 flexible board and IS-016 flexible board) (including ACT-001 flexible board and HOL-004 flexible board)
Page 104
Ver. 1.1 2007.10 The changed portions from 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST Ver. 1.0 are shown in blue. DISASSEMBLY HARDWARE LIST 5-1-13. HALF BODY SECTION (AF MODULE) ns: not supplied Mirror Box Section (Penta Unit) (See page 5-15) J901 (including AF-110 flexible board) J902...
Page 105
Ver. 1.1 2007.10 The changed portions from 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST Ver. 1.0 are shown in blue. DISASSEMBLY HARDWARE LIST 5-1-14. MIRROR BOX SECTION (PENTA UNIT) (including AE-029 flexible board and IFL-002 flexible board) (Note 1) 654 - 657 (Note 1) (Note 2)
Page 106
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-15. MIRROR BOX SECTION (SUB UNIT-1) (including AP-031 flexible board) Mirror Box Section (Sub Unit-2) (See page 5-17) 705 706 (including AFM-001 flexible board and AFP-003 flexible board) Ref. No. Part No.
Page 107
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-16. MIRROR BOX SECTION (SUB UNIT-2) ns: not supplied (including BL-012 flexible board) (including SLK-002 flexible board) Ref. No. Part No. Description Ref. No. Part No. Description 3-268-935-01 SP, SUB MIRROR FUNCTION X-2179-721-1 CHARGE BASE PLATE B ASSY A-1317-686-A BL CONTACT HOLDER UNIT (including SLK-002 flexible board)
Page 108
Electrical parts list of the AM-012 and DD- 280 boards are not shown. Pages 5-18 to 5-27 are not shown. DSLR-A700_L2...
Page 112
Ver. 1.3 2008.08 The changed portions from Ver. 1.2 are shown in blue. Checking supplied accessories. Note 1: This item is supplied with the unit as an accessory, but is not prepared as a service part. Battery Charger Power Cord Eyecup CD-ROM 0 1-790-107-61 (US, CND)
Page 114
& : Points added portion. : Points changed portion. 5. REPAIR PARTS LIST 5-1. EXPLODED VIEWS Page Former Ref. No. Part No. Description Ref. No. Part No. Description 2-688-728-01 CAP, BODY 2-688-728-02 CAP, BODY 3-274-514-01 CUSHION, STOP 3-274-514-03 CUSHION, STOP 2-515-483-31 SCREW (M1.7), LOCK ACE, P2 (Black) 2-599-475-31 SCREW(M1.7) (Silver) 3-290-178-01 GUARD SHEET, TP FLEX...
Page 115
: Points changed portion. Page Former 5-12 Tebure Unit Section Tebure Unit Section (See page 5-13) (See page 5-13) Ref. No. Part No. Description Ref. No. Part No. Description 2-666-551-11 SCREW,TAPPING,P2 (Silver) 5-13 2-695-354-01 WASHER (Note 3) 3-292-847-01 WASHER (Note 3) Note 3: Note the direction when you install washers.
Reverse 985221235.pdf Revision History S.M. Rev. Ver. Date History Contents issued 2007.09 Official Release — — 2007.10 Revised-1 • Addition of Notes (A1 DI07-167) • Correction of Reference Number • Addition of Informations of Repair Parts S.M. revised: Page 1-2, Page 1-5, Page...