hit counter script
Toro CCR POWERLITE 38170 Operator's Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Snow Blower
  5. CCR POWERLITE 38170
  6. Operator's manual
Toro CCR POWERLITE 38170 Operator's Manual

Toro CCR POWERLITE 38170 Operator's Manual

Hide thumbs Also See for CCR POWERLITE 38170:
Table of Contents

Advertisement

Quick Links

See also: Operator's Manual
CCR POWERLITE
Snowthrower
Model No. 38170—200000001 and Up
Model No. 38172—200000001 and Up
Model No. 38182—200000001 and Up
Operator's Manual
Pour obtenir gratuitement une version en français de ce manuel, écrivez à l'adresse
ci-dessous. N'oubliez pas d'indiquer les numéros de modèle et de série de votre produit.
The Toro Company, Attn: Parts Dept., 8111 Lyndale Ave S, Bloomington, MN 55420–1196
Form No 3322-818 Rev A
Domestic English (EN)

Advertisement

Table of Contents
loading

Related Manuals for Toro CCR POWERLITE 38170

Summary of Contents for Toro CCR POWERLITE 38170

  • Page 1 Pour obtenir gratuitement une version en français de ce manuel, écrivez à l’adresse ci-dessous. N’oubliez pas d’indiquer les numéros de modèle et de série de votre produit. The Toro Company, Attn: Parts Dept., 8111 Lyndale Ave S, Bloomington, MN 55420–1196 Domestic English (EN)

  • Page 2: Table Of Contents

    Introduction mechanical information and Note emphasizes general information worthy of special attention. Thank you for choosing a Toro product. We want you to be completely satisfied with your new purchase. Safety Read this manual carefully to learn how to operate and maintain your product properly.

  • Page 3: General Snowthrower Safety

    The following instructions have been adapted from the while performing an adjustment or repair. ANSI/OPEI standard B71.3—1995 and ISO standard 8437:1989. Information or terminology specific to Toro snowthrowers is enclosed in parenthesis. Operation Do not put hands or feet near or under rotating parts.

  • Page 4: Toro Snowthrower Safety

    To ensure the best performance and safety, purchase Toro Snowthrower Safety only genuine Toro replacement parts and accessories to keep the Toro all Toro. Do not use “Will Fit” The following list contains safety information specific to replacement parts and accessories as they could Toro products or other safety information that you must cause a safety hazard.

  • Page 5: Safety And Instruction Decals

    Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. On Control Panel (Model 38182) On Control Panel (Models 38170 and 38172) (Part No.

  • Page 6: Assembly

    Assembly Note: Determine the left and right sides of the snowthrower by standing in the normal operating position. Loose Parts DESCRIPTION QTY. Hex bolts Locknuts Installing the discharge chute Washers Discharge chute Upper handle Knobs Installing the handle Oval head bolts Curved washers Installing the Discharge Chute 3.
  • Page 7 Never buy more than a 30-day supply of container label. gasoline. For best results, use Toro Heavy Duty 50:1 All Season 2-Cycle Engine Oil with Fuel Stabilizer. 3. Install the cap on the gasoline container and shake the container to mix the gasoline and oil thoroughly.

  • Page 8: Operation

    1. Turn the key to the On position. Note: If you use Toro Heavy Duty 50:1 All Season 2-Cycle Engine Oil with Fuel Stabilizer, you do not need 2. Turn the choke level to the On (far right) position.

  • Page 9: Stopping The Engine

    C. When the engine starts, disconnect the power cord strike the ground. The wheels do not need to touch the from the snowthrower and the outlet. ground to self-propel. The more you tilt the handle forward, the faster the snowthrower self-propels. 5.

  • Page 10: Maintenance

    Note: When you unfold the handle the discharge chute, tighten all the knobs securely. Figure 7 1. Discharge chute 3. Handle 2. Discharge chute handle Maintenance Recommended Maintenance Schedule Service Item Service Operation Initial Comments Storage Drain the fuel and run the engine until the fuel tank Fuel tank and the carburetor are dry.

  • Page 11: Replacing The Scraper

    Replacing the Scraper 5. Pull the idler pulley up slightly while pulling out the drive belt. Allow the pulley to gradually release when it can move past the belt (Fig. 10). Before each season, inspect the scraper for wear. If the thickness of the scraper’s bottom is less than 1/16 in.

  • Page 12: Replacing The Spark Plug

    9. Install the drive belt cover and tighten the fasteners securely, but do not overtighten. .030 in. (.76 mm) Replacing the Spark Plug Before each season, check the spark plug. If the electrodes in the center of the plug are dark or have deteriorated, install a new NGK BPMR4A spark plug.

  • Page 13: Storage

    6. Recycle the fuel according to local codes. mix it it with fresh gasoline. Preparing the Engine Note: If you use Toro Heavy Duty 50:1 All Season 2-Cycle Engine Oil with Fuel Stabilizer, you do not need to add a fuel stabilizer/conditioner.

  • Page 14: Tightening The Fasteners And Cleaning The Snowthrower

    Tightening the Fasteners and Cleaning the Snowthrower 1. Tighten all loose screws, bolts, and locknuts. Repair or replace damaged parts. 2. Clean the snowthrower thoroughly. Covering and Storing the Snowthrower Cover the snowthrower and store it in a clean, dry place out of the reach of children.

  • Page 16: Warranty

    Countries Other than the United States or Canada Customers who have purchased Toro Products exported from the United States or Canada should contact their Toro Dis- tributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer.

This manual is also suitable for:

Ccr powerlite 38172Ccr powerlite 38182

Table of Contents