Related Manuals for Canon USB Application Interface Board-D1
Summary of Contents for Canon USB Application Interface Board-D1
- Page 1 USB Application Interface Board-D1 SERVICE MANUAL DU7-1136-000 SEPT. 2004 REV. 0 COPYRIGHT 2004 CANON INC. CANON imageRUNNER USB Application Interface Board-D1 REV. 0 PRINTED IN U.S.A.
- Page 2 This manual may contain technical inaccuracies or typographical errors due to improvements or changes in products. When changes occur in applicable products or in the contents of this manual, Canon will release technical information as the need arises. In the event of major changes in the contents of this manual over a long or short period, Canon will issue a new edition of this manual.
- Page 3 Introduction Symbols Used This documentation uses the following symbols to indicate special information: Symbol Description Indicates an item of a non-specific nature, possibly classified as Note, Caution, or Warning. Indicates an item requiring care to avoid electric shocks. Indicates an item requiring care to avoid combustion (fire). Indicates an item prohibiting disassembly to avoid electric shocks or problems.
- Page 4 Introduction The following rules apply throughout this Service Manual: 1. Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical and mechanical systems with reference to the timing of operation. In the diagrams, represents the path of mechanical drive; where a signal name accompanies the symbol, the arrow indicates the direction of the electric signal.
-
Page 5: Table Of Contents
Contents Contents Chapter 1 Specifications 1.1 Product composition ....................1-1 1.1.1 Product Configuration..................1-1 1.2 Specifications......................1-2 1.2.1 Specifications ...................... 1-2 Chapter 2 Installation 2.1 Checking components....................2-1 2.1.1 Checking the Contents ..................2-1 2.2 Installation procedure ....................2-2 2.2.1 Installation Procedure (iR4570/3570, 2870/2270 Series) ........2-2 2.2.2 Mounting the Ferrite Core (outside North America) .......... -
Page 6: Chapter 1　Specifications
Chapter 1 Specifications... - Page 7 Contents Contents 1.1 Product composition...................1-1 1.1.1 Product Configuration.................1-1 1.2 Specifications .....................1-2 1.2.1 Specifications ..................1-2...
-
Page 8: Product Composition
Chapter 1 1.1 Product composition 1.1.1 Product Configuration 0008-5313 This kit consists of the following items. F-1-1 T-1-1 Security Expansion Board (USB) - D1 Ferrite Core Tie-wrap... -
Page 9: Specifications
Chapter 1 1.2 Specifications 1.2.1 Specifications 0008-5316 The Security Expansion Board (USB)-D1, an optional board connected with PCI, has 2 functions. One is to add 2 USB host terminals required when the IC card reader or the like is connected to the host machine with USB in MEAP environment. The other is to add the encryption accelerator chip required when HDD encryption processing is speeded up during installation of the security kit. - Page 10 Chapter 2 Functions...
- Page 11 Contents Contents 2.1 Checking components ................2-1 2.1.1 Checking the Contents ................2-1 2.2 Installation procedure.................2-2 2.2.1 Installation Procedure (iR4570/3570, 2870/2270 ......2-2 2.2.2 Mounting the Ferrite Core (outside North America) ......2-6...
-
Page 12: Checking Components
Chapter 2 2.1 Checking components 2.1.1 Checking the Contents 0007-7638 F-2-1 T-2-1 USB Application Interface Board-D1 1 pc. Ferrite core 2 pc. Tie-wrap 2 pc. Caution 1. You will need the ferrite core and tie-wrap if you will be connecting a USB cable for connection of a USB device. -
Page 13: Installation Procedure
Chapter 2 2.2 Installation procedure 2.2.1 Installation Procedure (iR4570/3570/2870/2270 Series) 0007-7643 1. Turning Off the Host Machine Before starting the work, be sure to perform the following on the host machine in strict sequence: 1. Hold down the control panel power switch for 3 sec or more. 2. - Page 14 Chapter 2 2. Checks to Make Before Starting the Installation Work If you are installing a USB Application Interface Board-D1 be sure that the Expansion Bus-B1 already exists. 3. Installation 1) Remove the 4 screws [1]. 2) Loosen the 2 screws [2].
- Page 15 Chapter 2 4) Remove the 2 screws [1], and detach the face plate [2]. The detached face plate will no longer be used. F-2-5 5) Install the USB application interface board [1] as shown. (Move the board as indicated by the arrow.) F-2-6...
- Page 16 Chapter 2 6) Fix the USB application interface board [1] in place using 2 screws [2]. F-2-7 7) Mount the face cover using 4 screws. 8) Tighten the 2 screws loosened in step (2). 9) Connect the host machine's power cable (to the power outlet). 10) Turn on the main power switch.
-
Page 17: Mounting The Ferrite Core (Outside North America)
Chapter 2 2.2.2 Mounting the Ferrite Core (outside North America) 0007-8168 Be sure to perform the following if you are using a USB cable for connection of a USB device. 1) When you have connected the USB cable, fit the ferrite core [1] to the cable. Be sure that the distance shown [2] is 100 mm or less. - Page 18 Chapter 2 F-2-9 If you are using 2 USB cables, be sure to fit the other cable with another ferrite core and tie-wrap in the same way.
- Page 19 Chapter 3 Parts Replacement Procedure...
- Page 20 Contents Contents 3.1 Related Service Mode ................3-1 3.1.1 Service Mode List ................3-1...
-
Page 21: Related Service Mode
Chapter 3 3.1 Related Service Mode 3.1.1 Service Mode List 0008-5321 The following is an overview of service mode related to USB Application Interface Boad- T-3-1 Item Settings Detail Board name Copier>Display> Not connected: [-] hyphen is displayed. connected to PCI 1/ ACC-STS>PCI1/ Connected: Board name is displayed.