Canon BW PCL PRINTER KIT-J1 Installation Procedure
Hide thumbs
Also See for BW PCL PRINTER KIT-J1:
- Installation procedure (6 pages) ,
- Service manual (28 pages)
Related Manuals for Canon BW PCL PRINTER KIT-J1
Summary of Contents for Canon BW PCL PRINTER KIT-J1
- Page 1 Installation Procedure Canon BW PCL PRINTER KIT-J1 Sep 14 2005...
- Page 3 Canon will release technical information as the need arises. In the event of major changes in the contents of this manual over a long or short period, Canon will issue a new edition of this manual. The following paragraph does not apply to any countries where such provisions are inconsistent with local law.
- Page 4 Introduction Symbols Used This documentation uses the following symbols to indicate special information: Symbol Description Indicates an item of a non-specific nature, possibly classified as Note, Caution, or Warning. Indicates an item requiring care to avoid electric shocks. Indicates an item requiring care to avoid combustion (fire). Indicates an item prohibiting disassembly to avoid electric shocks or problems.
- Page 5 Introduction The following rules apply throughout this Service Manual: 1. Each chapter contains sections explaining the purpose of specific functions and the rela- tionship between electrical and mechanical systems with reference to the timing of operation. In the diagrams, represents the path of mechanical drive; where a signal name accom- panies the symbol , the arrow indicates the direction of the electric signal.
-
Page 7: Table Of Contents
Contents Contents Chapter 1 Installation Procedure 1.1 Checking components ............................2 1.1.1Checking the Contents..........................2 1.2 Installation procedure............................3 1.2.1Mounting to the Host Machine ........................3 1.2.2Checking the Connection ..........................6... - Page 8 Contents...
-
Page 9: Chapter 1 Installation Procedure
Chapter 1 Installation Procedure... -
Page 10: Checking Components
Chapter 1 1.1 Checking components 1.1.1 Checking the Contents 0010-7372 F-1-1 32MB ROM 1 pc. 256MB RAM 1 pc. Screw (binding; M3X4) 1 pc. User software CD-ROM 1 pc. Release Note 1 pc. User's Manual CD-ROM 1 pc. -
Page 11: Installation Procedure
Chapter 1 1.2 Installation procedure If an optional Super G3 Fax Board-T1 is found, the SDRAM and the super capacitor remain powered to back up the image memory (even after the main power 1.2.1 Mounting to the switch has been turned off and the power plug has been disconnected). - Page 12 Chapter 1 F-1-6 F-1-8 7) If a UFRII LT PRINTER KIT-J2 is installed, per- form steps 7-1) and 7-2). 8) Disconnect the soft ID cable [1]. 7-1) Remove the LAN cover [1]. - 1 cable clamp [2] - 4 screws [2] F-1-9 F-1-7 9) Release the claw [1] of the cable guide, and free the...
- Page 13 Chapter 1 10) Remove the IP cover [1]. - 10 screws [2] F-1-13 13) Attach the IP cover you removed in step 10). F-1-11 When attaching the IP cover, take care not to damage the grounding plate [2] by the USB port [1]. 11) Shift the 2 locking levers [1] back to their initial Also, after attaching the IP cover, check to make sure position.
-
Page 14: 2Checking The Connection
Chapter 1 UFRII LT PRINTER KIT-J2 is mounted) G3 Fax Board-T1 is mounted) - rear left cover - rear cover 18) Connect the power plug, and turn on the main When attaching the LAN cover, take care not to dam- power switch. - Page 15 Sep 14 2005...