Does the VM130V2SET work at the 5 GHz Wi-Fi frequency? ............20 Can I modify the RF frequency (433 MHz)? ..................20 Can I buy a transmitter separately to pair to an existing VM130V2SET? ......... 20 RED Declaration of Conformity ......................20...
Warnings • This VM130V2SET is suited for indoor use. • The VM130V2SET cannot be used to operate machines. • Replace the transmitter’s battery if transmission becomes weak. • Do not mount the receiver in the proximity of other electronic devices or metal objects to guarantee a good reception of the wireless signals.
(5) Power LED Overview (6) TUYA LED not used (2) CH1 Button (3) CH2 Button (7) CH1 LED (4) Indicator LED (8) CH2 LED (1) LED Button (9) SETUP Button (10) CH1 RELAY (11) CH2 RELAY (12) POWER INPUT TERMINAL Mounting the Receiver Mounting hole Mounting hole...
First Set-Up Connect the receiver with the supplied power supply: position the bare wires into the power input terminal (12) on the board. The black (GND) wire goes into the “-“ terminal, the red (+12VDC) wire goes into the “+” terminal. Use a flat screwdriver to tighten the screws of the terminals. If the power supply is successfully connected, the power LED (5) will light up and the TUYA LED (6) will start flashing after a few seconds.
Connecting the Receiver to the TUYA IoT Cloud (optional) 1. Install the TUYA app or SmartLife app on your smartphone and create a TUYA account. 2. Make sure there is a stable Wi-Fi connection with internet access present where the receiver is installed.
Page 7
8. Select the network you wish to use for the VM130V2SET and enter the password for the W-Fi network. Attention: Make sure it is a 2.4 GHz network! The VM130V2SET does not work on a 5 GHz network. 9. If the app asks to press the “reset” button, use the SETUP button (9). The TUYA LED (6) should start blinking rapidly when in pairing mode.
Page 8
It will automatically connect to the cloud. Connecting the receiver with the TUYA IoT cloud is optional. If not connected to the cloud, the functionality of the VM130V2SET will be limited to ON/OFF functions for both channels with the transmitter. P a g e...
12 V LED strip connected to channel 1 on the NC (normally closed) and COM (common) terminals. The LED strip shares the power supply voltage of the power supply unit with the VM130V2SET. When connecting the schematic below, the LED strip will burn as long as channel 1 is off. When switching on channel 1 the LED strip will switch off.
6. All transmitters are now cleared from the receiver’s memory. Please note you will need to re-pair a transmitter to the receiver. Using the VM130V2SET with the Transmitter Press the CH1 button (2) on the transmitter for minimum 2 seconds to change the state of the CH1 relay (10) on the receiver.
Using the VM130V2SET with the TUYA App This requires an internet connection on your smartphone and a good Wi-Fi connection to the receiver. 1. Open the TUYA app or SmartLife app on your smartphone and select the “Power Strip” device.
Page 12
4. Use the ‘Schedule function’ to add multiple times during the day or week when you want each individual channel to turn on or off. Determine when it must be repeated with the “Repeat” option. P a g e | 11...
Page 13
5. Add every channel onto you wish to switch a channel with the “Add Schedule” button. 6. By using the “Smart” tab in the app, you can specify several actions that will control the channels. Example 1: Switching a channel based on the sunrise In this example, we will create a smart action based on “When weather changes”.
Page 15
In the next step, we select our location and the specific moment when we wish to switch. After choosing the input, we then select the “Run the device” action and choose for the VM130V2. Now, we select the desired channel we wish to switch at sunrise, in this case channel 1 (Switch 1). Select the ‘ON’...
Page 17
Example 2: Making a channel ‘pulse’ In this example we want channel 1 to act as a ‘pulse’ contact. In other words, when the channel switches, it will switch back automatically after a set time. This function is interesting to switch a garage door, which only needs a short ‘on’...
Page 18
We select channel 1 (Switch 1) and the “OFF” situation. Finally, we have an overview of the set ‘smart’ action: When channel 1 is activated, it will switch off after a delay of 2 seconds. P a g e | 17...
Page 19
You can add more smart actions to the VM130V2 and couple to other smart devices which you have added to your app. This way, you could couple a VM130V2SET to another VM130V2SET and control one VM130V2 and – via TUYA – the other VM130V2 with only a single transmitter.
Bad reception between the receiver and the TUYA IoT cloud Frequent reception loss between the VM130V2SET and the TUYA app or SmartLife app is often due to an unstable Wi-Fi connection. Place your smartphone close to the receiver and check the W-Fi strength at that location.
TUYA IoT cloud (where you switch the device on and off a couple of times). The VM130V2SET is designed to stay switched on permanently. This situation only happens at start-up.