Sony CFD-E55 Service Manual
Hide thumbs
Also See for CFD-E55:
- Operating instructions manual (72 pages) ,
- Operating instructions manual (36 pages) ,
- Service manual (44 pages)
Table of Contents
Advertisement
Quick Links
http://www.jdwxzlw.com/?fromuser=SNvÛ~ôOî
SERVICE MANUAL
Ver. 1.2 2005.09
AUDIO POWER SPECIFICATIONS
(US model only)
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
With 3.2-ohm loads, both channels driven
from 100 - 10,000 Hz; rated 1.5 W per
channel-minimum RMS power, with no more
than 10 % total harmonic distortion in AC
operation.
Other Specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20,000 Hz +0/–0.5 dB
Wow and flutter
Below measurable limit
Radio section
– US, Canadian, E92*, Mexican models –
Frequency range
FM: 87.6 - 108 MHz
AM: 530 - 1,710 kHz
Aerials
FM: Telescopic aerial
AM: Built-in ferrite bar aerial
– Singapore, Argentine, Australian models –
Frequency range
FM: 87.6 - 108 MHz
AM: 531 - 1,602 kHz
Sony Corporation
9-927-159-13
Personal Audio Group
2005I05-1
Published by Sony Engineering Corporation
© 2005.09
[¶u5~ôOî•De™•QÿQM•9N•}TyÍ~ôOî•De™
Model Name Using Similar Mechanism
CD
CD Mechanism Type
Section
Optical Pick-up Name
Model Name Using Similar Mechanism
TAPE
Section
Tape Transport Mechanism Type
SPECIFICATIONS
IF
FM: 10.7 MHz
AM/MW: 450 kHz
Aerials
FM: Telescopic aerial
AM/MW: Built-in ferrite bar aerial
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 120 sec. with Sony cassette C-60
Frequency response
TYPE I (normal): 70 - 13,000 Hz
General
Speaker
1
Full range: 8 cm (3
⁄
in.) dia.,
4
3.2 ohms, cone type (2)
Outputs
Headphones jack (stereo minijack)
For 16 - 68 ohms impedance headphones
Power output (excluding for US model)
2 W + 2 W (at 3.2 ohms, 10 % harmonic distortion
in AC operation)
Power requirements
For CD radio cassette-corder:
120 V AC, 60 Hz (US, Canadian, E92*,
Mexican models)
230 V AC, 50Hz (Singapore, Argentine,
Australian models)
9 V DC, 6 size D (R20) batteries
For memory back-up:
4.5 V DC, 3 size AA (R6) batteries
CD RADIO CASSETTE-CORDER
CFD-E55
US Model
Canadian Model
Australian Model
CFD-Z500
KSM-213CDM
KSS-213C
CFD-Z500
MF-Z500-117
Power consumption
AC 17 W
Battery life
For CD radio cassette-corder:
FM recording
Sony manganese SUM-1 (N): approx. 9 h
Sony alkaline AM-1 (N): approx. 19 h
Tape playback
Sony manganese SUM-1 (N): approx. 5 h
Sony alkaline AM-1 (N): approx. 14 h
CD playback
Sony manganese SUM-1 (N): approx. 1.5 h
Sony alkaline AM-1 (N) : approx. 7 h
Dimensions
Approx. 304 × 169 × 262 mm (w/h/d)
(12 × 6
× 10
3
⁄
3
⁄
inches) (incl. projecting parts)
4
8
Mass
Approx. 3.6 kg (7 lb. 15 oz) (incl. batteries)
Supplied accessories
AC power cord (1)
Instruction manual (1)
*E92: Central and South America
Design and specifications are subject to change without
notice.
E Model
Advertisement
Table of Contents
Related Manuals for Sony CFD-E55
Summary of Contents for Sony CFD-E55
-
Page 1: Specifications
TYPE I (normal): 70 - 13,000 Hz CD playback System Sony manganese SUM-1 (N): approx. 1.5 h General Compact disc digital audio system Sony alkaline AM-1 (N) : approx. 7 h Laser diode properties Speaker Material: GaAlAs Full range: 8 cm (3 ⁄... -
Page 2: Table Of Contents
OPERATION. REPLACE THESE COMPONENTS WITH DE FONCTIONNEMENT. NE REMPLACER CES COM- SONY PARTS WHOSE PART NUMBERS APPEAR AS POSANTS QUE PAR DES PIÈCES SONY DONT LES SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- NUMÉROS SONT DONNÉS DANS CE MANUEL OU LISHED BY SONY. -
Page 3: Servicing Notes
h t t p : / / w w w . j d w x z l w . c o m / ? f r o m u s e r = S N v ~ O SECTION 1 SERVICING NOTES NOTES ON HANDLING THE OPTICAL PICK-UP CAUTION... - Page 4 http://www.jdwxzlw.com/?fromuser=SNvÛ ~ ô O î MODEL TYPE IDENTIFICATION In this set, the routing of speaker lead wires and the boards have been changed in the midway of production, and the set is grouped into the following four types depending on the specifications. TYPE A: Original model.
-
Page 5: General
http://www.jdwxzlw.com/?fromuser=SNv¤~ÙOÓ SECTION 2 This section is extracted from instruction manual. GENERAL – 5 – [∂u5~ÙOÓçDeôQˇQMç9Nè}TyÕ~ÙOÓçDeô... - Page 6 http://www.jdwxzlw.com/?fromuser=SNv¤~ÙOÓ – 6 – [∂u5~ÙOÓçDeôQˇQMç9Nè}TyÕ~ÙOÓçDeô...
- Page 7 http://www.jdwxzlw.com/?fromuser=SNv¤~ÙOÓ – 7 – [∂u5~ÙOÓçDeôQˇQMç9Nè}TyÕ~ÙOÓçDeô...
-
Page 8: Disassembly
http://www.jdwxzlw.com/?fromuser=SNv¤ ~ Ù O Ó SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. Lower cabinet Optical pick-up Front cabinet MAIN board CD board section section section POWER board Tape mechanism Cassette lid assy CD lid deck section and cassette holder section... - Page 9 http://www.jdwxzlw.com/?fromuser=SNv¤ ~ Ù O Ó POWER BOARD 1 three screws (BVTP3 × 10) 2 RETAINER board 3 POWER board FRONT CABINET SECTION 1 three connectors (CNP302, 303, 309) 2 two screws (BVTP3 × 12) 2 two screws (BVTP3 × 12) 3 Remove the front cabinet section in the direction of arrow A.
- Page 10 h t t p : / / w w w . j d w x z l w . c o m / ? f r o m u s e r = S N v ~ O MAIN BOARD 1 two connectors TYPE A (CNP306, 312)
- Page 11 http://www.jdwxzlw.com/?fromuser=SNv¤ ~ Ù O Ó • CONNECTOR SETTING (TYPE B, C, D) Note: When connecting speaker lead, set it as shown in the figure. POWER board speaker lead bracket (SP) BH354 (TYPE B, C) speaker lead bracket (SP) BH351 (TYPE D) CNP307 CNP308 BH353...
- Page 12 http://www.jdwxzlw.com/?fromuser=SNv¤ ~ Ù O Ó CD LID SECTION 4 Open the CD lid section 5 Remove the boss. 6 CD lid section 2 damper 1 screws (BTP3 × 10) 3 spring (CD) TAPE MECHANISM DECK SECTION 4 tape mechanism deck section 1 Push the button (ST/EJ).
- Page 13 http://www.jdwxzlw.com/?fromuser=SNvÛ ~ ô O î CASSETTE LID ASSY AND CASSETTE HOLDER 8 boss 7 spring (cassette) 8 boss 3 two screws (BVTP3 × 10) 4 speaker (R ch) 9 cassette lid assy and “holder, cassette” 6 damper 5 screw 2 bracket (SP) (BVTP3 ×...
-
Page 14: Mechanical Adjustments
http://www.jdwxzlw.com/?fromuser=SNvÛ ~ ô O î SECTION 4 SECTION 5 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS PRECAUTION PRECAUTION 1. Clean the following parts with a denatured-alcohol-moistened 1. Setting swab : SOUND control : OFF record/playback head pinch roller erase head rubber belts TAPE DECK SECTION 0 dB=0.775 V capstan idlers... -
Page 15: Tuner Section
http://www.jdwxzlw.com/?fromuser=SNvÛ ~ ô O î ( ): Singapore, Argentine, Australian models 0 dB=1 µV TUNER SECTION AM IF ADJUSTMENT [AM] Adjust for a maximum reading on level meter Setting: 450 kHz Function : RADIO BAND button : AM AM VCO VOLTAGE ADJUSTMENT POWER board BH352 pin 1 (TYPE A) Adjustment Part Frequency Display Reading on Digital Voltmeter... - Page 16 http://www.jdwxzlw.com/?fromuser=SNvÛ ~ ô O î Adjustment Location (TYPE A, B, C): (TYPE D: Almoset same as TYPE A, B, C) – MAIN BOARD (Component Side) – T1 AM IF Adjustment FM Tracking Adjustment FM VCO Voltage Adjustment AM VCO Voltage Adjustment AM Tracking Adjustment –...
-
Page 17: Cd Section
http://www.jdwxzlw.com/?fromuser=SNv¤~ÙOÓ CD SECTION CD section adjustments are done automatically in this set. In case of operation check, confirm that focus bias. Focus Bias Check 1. Connect the oscilloscope to TP (RFO) and TP (GND) on the CD board. 2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01) 3. -
Page 18: Diagrams
~ Ù O Ó CFD-E55 SECTION 6 DIAGRAMS 6-1. BLOCK DIAGRAM – CD Section – CD BOARD (1/2) FILTER DIGITAL SIGNAL PROCESSOR, CLV SERVO, D/A CONVERTER IC703 ERROR CNP701 CORRECTOR PD1 I-V AMP PCMD PCMDI DETECTOR OVER BCKI ASYMMETRY... -
Page 19: Block Diagram - Tuner Section
~ ô O î CFD-E55 6-2. BLOCK DIAGRAM – TUNER Section – TO MAIN SECTION MAIN BOARD (1/3) (TYPE A: Page 23) 10.7MHz (TYPE B, C: Page 25) (TYPE D: Page 27) ANT1 FM TELESCOPIC ANTENNA FM/AM RF AMP, MIX, OSC,... - Page 20 ~ ô O î CFD-E55 6-3. BLOCK DIAGRAM – MAN Section (TYPE A) – • SIGNAL PATH MAIN BOARD (2/3) POWER BOARD (1/2) : CD PLAY P-CON CNP304 (1/2) : TUNER (FM/AM) REC/PB EQ AMP FROM POWER : TAPE PLAY...
-
Page 21: Block Diagram - Main Section (Type A)
~ ô O î CFD-E55 6-4. BLOCK DIAGRAM – MAIN Section (TYPE B, C) – • SIGNAL PATH MAIN BOARD (2/3) POWER BOARD (1/2) : CD PLAY P-CON CNP304 (1/2) : TUNER (FM/AM) REC/PB EQ AMP FROM POWER : TAPE PLAY... -
Page 22: Block Diagram - Main Section (Type D)
~ ô O î CFD-E55 6-5. BLOCK DIAGRAM – MAIN Section (TYPE D) – • SIGNAL PATH MAIN BOARD (2/3) POWER BOARD (1/2) : CD PLAY P-CON CNP304 (1/2) : TUNER (FM/AM) REC/PB EQ AMP FROM POWER : TAPE PLAY... -
Page 23: Block Diagram - Power Supply Section
~ Ù O Ó CFD-E55 6-6. BLOCK DIAGRAM – POWER SUPPLY Section – • Circuit Boards Location CD BOARD (2/2) POWER BOARD (2/2) CNP704 BH351 (TYPE A, B, C) PVDD CD MOTOR/COIL CD board BH701 FROM MAIN SECTION DRIVER (IC702) B+... -
Page 24: Printed Wiring Boards – Cd Section (Type D)
CFD-E55 http://www.jdwxzlw.com/?fromuser=SNvÛ ~ ô O î 6-7. PRINTED WIRING BOARDS – CD Section (TYPE A, B, C) – • See page 31 for Circuit Boards Location. 6-8. PRINTED WIRING BOARDS – CD Section (TYPE D) – • See page 31 for Circuit Boards Location. -
Page 25: Schematic Diagram - Cd Section (Type A, B, C, D)
~ ô O î CFD-E55 6-9. SCHEMATIC DIAGRAM – CD Section (TYPE A, B, C, D) – • See page 56 for Waveforms. • See page 72 for IC Block Diagrams. (TYPE A, B, C: Page 59) (TYPE D: Page 61) - Page 26 CFD-E55 http://www.jdwxzlw.com/?fromuser=SNvÛ ~ ô O î 6-10. PRINTED WIRING BOARDS – MAIN/POWER SUPPLY Section (TYPE A, B) – • See page 31 for Circuit Boards Location. • Semiconductor Location Ref. No. Location Ref. No. Location IC302 IC303 C-15 D321 Q301...
- Page 27 ~ ô O î CFD-E55 6-11. PRINTED WIRING BOARDS – MAIN/POWER SUPPLY Section (TYPE C) – • See page 31 for Circuit Boards Location. • Semiconductor Location Ref. No. Location Ref. No. Location IC302 IC303 C-15 D321 Q301 D322...
- Page 28 CFD-E55 http://www.jdwxzlw.com/?fromuser=SNvÛ ~ ô O î 6-12. PRINTED WIRING BOARDS – MAIN/POWER SUPPLY Section (TYPE D) – • See page 31 for Circuit Boards Location. • Semiconductor Location Ref. No. Location Ref. No. Location IC302 IC303 C-15 D321 D322 Q301...
-
Page 29: Schematic Diagram - Main (Tuner) Section (Type A, B, C, D)
~ ô O î CFD-E55 6-13. SCHEMATIC DIAGRAM – MAIN (TUNER) Section (TYPE A, B, C, D) – • • See page 56 for Waveform. See page 74 for IC Block Diagrams. • Waveforms – CD Board – – MAIN Board (TUNER Section) –... -
Page 30: Schematic Diagram - Main (Audio) Section (Type A, B, C, D), Power Supply Section (Type A, B, C)
CFD-E55 http://www.jdwxzlw.com/?fromuser=SNvÛ ~ ô O î 6-14. SCHEMATIC DIAGRAM – MAIN (AUDIO) Section (TYPE A, B, C, D), POWER SUPPLY Section (TYPE A, B, C) – • See page 75 for IC Block Diagrams. (Page 61) Note on Schematic Diagram: •... -
Page 31: Schematic Diagram - Power Supply Section (Type D)
~ ô O î CFD-E55 6-15. SCHEMATIC DIAGRAM – POWER SUPPLY Section (TYPE D) – • See page 75 for IC Block Diagram. (Page 59) Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. -
Page 32: Printed Wiring Boards - Display Section (Type A, B)
~ ô O î CFD-E55 6-16. PRINTED WIRING BOARDS – DISPLAY Section (TYPE A, B) – • See page 31 for Circuit Boards Location. (Page 33) (Page 42) (Page 42) (EXCEPT AUS) (Page 43) • Semiconductor Location Ref. No. Location Ref. -
Page 33: Printed Wiring Boards - Display Section (Type C)
~ ô O î CFD-E55 6-17. PRINTED WIRING BOARDS – DISPLAY Section (TYPE C) – • See page 31 for Circuit Boards Location. (Page 33) (Page 45) (Page 45) (Page 46) • Semiconductor Location Ref. No. Location Ref. No. Location... -
Page 34: Printed Wiring Boards - Display Section (Type D)
~ ô O î CFD-E55 6-18. PRINTED WIRING BOARDS – DISPLAY Section (TYPE D) – • See page 31 for Circuit Boards Location. (Page 35) (Page 50) (Page 50) (Page 51) • Semiconductor Location Ref. No. Location Ref. No. Location... -
Page 35: Schematic Diagram - Display Section (Type A, B, C, D)
~ Ù O Ó CFD-E55 6-19. SCHEMATIC DIAGRAM – DISPLAY Section (TYPE A, B, C, D) – • See page 56 for Waveforms. (Page 58) (Page 58) (Page 39) Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. - Page 36 http://www.jdwxzlw.com/?fromuser=SNvÛ ~ ô O î • IC Block Diagrams – MAIN Board – IC702 BA6898FP – CD Board – IC1 TA2104BN IC701 CXA1992BR GND1 FM RF OUT FM RF 33 32 31 30 VCC1 FM RF IN LEVEL SHIFT LEVEL SHIFT AM RF IN AM LOW OUT PD 2...
-
Page 37: Power Board
http://www.jdwxzlw.com/?fromuser=SNv¤ ~ Ù O Ó IC301 TA2068N IC302 BH3854AS LINE LINE AGND FILTER OUT1 AMP1 BUF AMP TAPE RADIO RADIO BVN1 BVN2 BIN1 BIN2 MATRIX AMP1 BVO1 BVO2 PLAY SURROUND OUT1 TIN1 TIN2 MONITOR 26dB BUF AMP MUTE TVO2 TVO1 OUT1 OUT2 OUT1... -
Page 38: 6-20. Ic Pin Function Description
http://www.jdwxzlw.com/?fromuser=SNvÛ~ôOî 6-20. IC PIN FUNCTION DESCRIPTION • LCD BOARD IC501 CXP83620-011Q (SYSTEM CONTROLLER) Pin No. Pin Name Description C-SCOR Subcode sync (S0+S1) detection signal input from the CXD2589Q (IC703) Sircs remote control signal input terminal Not used (fixed at “L”) BUZZER Buzzer sound signal output terminal LED drive signal output of the ALARM indicator (D602) “L”: LED on... - Page 39 http://www.jdwxzlw.com/?fromuser=SNvÛ~ôOî Pin No. Pin Name Description B-MUTE Tuner muting on/off control signal output terminal “H”: muting on C-MUTE Digital muting on/off control signal output to the CXD2589Q (IC703) “H”: muting on Tape function control signal output to the TA2068N (IC301) TAPE “L”: radio or CD on, “H”: tape on RADIO...
-
Page 40: Exploded Views
http://www.jdwxzlw.com/?fromuser=SNv¤~ÙOÓ SECTION 7 EXPLODED VIEWS NOTE: • Items marked “*” are not stocked since they • -XX and -X mean standardized parts, so they The components identified by mark 0 or dotted line with mark may have some difference from the original are seldom required for routine service. - Page 41 http://www.jdwxzlw.com/?fromuser=SNvÛ ~ ô O î (2) MAIN BOARD AND CD SECTION S701 TYPE A, B, C KSM-213CDM Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-639-678-12 CD MOTOR BOARD 3-039-336-21 LID, CD (BLUE) 3-921-725-01 SCREW (2.6X10), +PWH 3-039-324-01 SPRING (CD) 3-910-095-31 RUBBER, VIBRATION PROOF 3-039-341-01 HANDLE (SILVER)
- Page 42 http://www.jdwxzlw.com/?fromuser=SNvÛ ~ ô O î (3) FRONT CABINET SECTION TYPE D MF-Z500-117 TYPE A, B, C SP201 SP101 supplied TYPE A, B, C TYPE D Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-039-300-01 LID, CASSETTE 3-039-306-11 BUTTON (FF) (M) (GREEN) 3-039-301-01 HOLDER, CASSETTE 3-039-306-21 BUTTON (FF) (M) (BLUE)
- Page 43 http://www.jdwxzlw.com/?fromuser=SNvÛ~ôOî (4) UPPER CABINET SECTION ANT1 LCD501 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 151 A-3322-186-A LCD BOARD, COMPLETE (US, CND, E92, MX) 3-041-268-21 LEVER (CD) (BLUE) * 151 A-3322-464-A LCD BOARD, COMPLETE (AUS) 3-041-268-11 LEVER (CD) (GREEN) * 151 A-3322-467-A LCD BOARD, COMPLETE (SP, AR)
- Page 44 http://www.jdwxzlw.com/?fromuser=SNvÛ~ôOî (5) TAPE MECHANISM DECK SECTION-1 (MF-Z500-117) HRP301 HE301 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-933-010-01 SPRING (S/P), TORSION * 212 3-008-587-01 SLIDER (STOP) 3-933-025-01 SPRING (P), TORSION * 213 3-008-591-01 SLIDER (PAUSE) 3-040-857-01 LEVER (P) 3-933-004-01 CLAW, REEL 3-933-024-01 ROLLER, PINCH * 215...
- Page 45 http://www.jdwxzlw.com/?fromuser=SNvÛ~ôOî (6) TAPE MECHANISM DECK SECTION-2 (MF-Z500-117) S304 S303 M301 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-933-029-01 LEVER, ERASING PREVENTION 3-343-358-01 RING, RETAINING 3-933-182-01 SPRING, CASSETTE 3-933-005-01 SPRING (CAM), COMPRESSION 3-932-995-01 GEAR (MID) 3-016-349-01 WASHER X-3371-667-1 CLUTCH ASSY 3-937-760-01 SPRING (GROUND), COMPRESSION 3-932-997-01 GEAR (CAM)
- Page 46 http://www.jdwxzlw.com/?fromuser=SNvÛ~ôOî (7) OPTICAL PICK-UP SECTION (KSM-213CDM) not supplied M701 M702 The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified.
-
Page 47: Electrical Parts List
http://www.jdwxzlw.com/?fromuser=SNv¤~ÙOÓ BATT (+) BATT (–) SECTION 8 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark are seldom required for routine service. parts list may be different from the parts speci- 0 are critical for safety. - Page 48 http://www.jdwxzlw.com/?fromuser=SNv¤~ÙOÓ Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C785 1-162-282-31 CERAMIC 100PF R721 1-249-435-11 CARBON 1/4W C786 1-162-282-31 CERAMIC 100PF R722 1-247-883-00 CARBON 150K 1/4W C787 1-162-294-31 CERAMIC 0.001uF R723 1-247-896-11 CARBON 510K 1/4W C790 1-162-284-31 CERAMIC 150PF R724...
- Page 49 http://www.jdwxzlw.com/?fromuser=SNv¤~ÙOÓ CD MOTOR KEY 1 KEY 2 KEY 3 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-639-678-12 CD MOTOR BOARD < RESISTOR > **************** < CONNECTOR > R608 1-249-427-11 CARBON 6.8K 1/4W R609 1-249-428-11 CARBON 8.2K 1/4W CNP707 1-564-722-11 PIN, CONNECTOR (SMALL TYPE) 6P...
- Page 50 http://www.jdwxzlw.com/?fromuser=SNv¤~ÙOÓ Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C507 1-162-205-31 CERAMIC 18PF (TYPE A, B, C) < CONNECTOR > C508 1-127-888-21 CERAMIC 0.1uF (TYPE A, B) * CNP501 1-785-658-11 PIN, CONNECTOR (PC BOARD) 6P C508 1-162-306-11 CERAMIC 0.01uF <...
- Page 51 http://www.jdwxzlw.com/?fromuser=SNv¤~ÙOÓ MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R532 1-249-422-11 CARBON 2.7K 1/4W (US, CND, E92, MX) 1-162-306-11 CERAMIC 0.01uF R532 1-249-428-11 CARBON 8.2K 1/4W 1-162-306-11 CERAMIC 0.01uF (SP, AR) 1-162-306-11 CERAMIC 0.01uF R533 1-249-425-11 CARBON 4.7K 1/4W...
- Page 52 http://www.jdwxzlw.com/?fromuser=SNv¤~ÙOÓ MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C221 1-162-301-11 CERAMIC 0.0015uF 20% * CNP307 1-785-661-11 PIN, CONNECTOR (PC BOARD) 9P C222 1-126-964-11 ELECT 10uF (TYPE A, B, C) C223 1-127-884-21 CERAMIC 0.047uF * CNP308 1-785-658-21 PIN, CONNECTOR (PC BOARD) 6P * CNP309 1-785-658-11 PIN, CONNECTOR (PC BOARD) 6P C224 1-127-884-21 CERAMIC...
- Page 53 http://www.jdwxzlw.com/?fromuser=SNv¤ ~ Ù O Ó MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q368 8-729-026-39 TRANSISTOR 2SA933AS-QT R145 1-249-437-11 CARBON 1/4W Q369 8-729-026-39 TRANSISTOR 2SA933AS-QT R151 1-247-887-00 CARBON 220K 1/4W Q370 8-729-036-62 TRANSISTOR KRC106M-AT R201 1-249-431-11 CARBON 1/4W Q371...
- Page 54 http://www.jdwxzlw.com/?fromuser=SNv¤~ÙOÓ MAIN POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSFORMER > C345 1-162-294-31 CERAMIC 0.001uF (TYPE A, B, C) 1-433-741-11 TRANSFORMER, IF C346 1-162-294-31 CERAMIC 0.001uF (TYPE A, B, C) < VIBRATOR > C351 1-161-494-00 CERAMIC 0.022uF...
- Page 55 http://www.jdwxzlw.com/?fromuser=SNv¤~ÙOÓ POWER REC SW Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < CONNECTOR > < TRANSISTOR > * CNP301 1-785-656-11 PIN, CONNECTOR (PC BOARD) 4P Q341 8-729-036-62 TRANSISTOR KRC106M-AT (TYPE A, B, C) Q351 8-729-801-84 TRANSISTOR 2SB1013-4 <...
- Page 56 CFD-E55 Ver. 1.2 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark ACCESSORIES ************ 1-557-287-11 CORD, POWER (E92, MX) 1-696-819-11 CORD, POWER (AUS) 1-769-412-11 CORD, POWER (SP) 1-782-126-11 CORD, POWER (US, CND) 1-783-952-11 CORD, POWER (AR)
- Page 57 http://www.jdwxzlw.com/?fromuser=SNvÛ~ôOî MEMO – 95 – [¶u5~ôOî•De™•QÿQM•9N•}TyÍ~ôOî•De™...
-
Page 58: Revision History
CFD-E55 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 1999.08...