Toshiba B-SX6T Series Option Installation Manual
Hide thumbs
Also See for B-SX6T Series:
- Owner's manual (139 pages) ,
- System mode manual (133 pages) ,
- Maintenance manual (24 pages)
Related Manuals for Toshiba B-SX6T Series
Summary of Contents for Toshiba B-SX6T Series
- Page 1 TOSHIBA Thermal Printer B-SX6T/SX8T SERIES Option Installation Manual Document No. EO15-33002 Original Mar., 2006 (Revised PRINTED IN JAPAN...
-
Page 2: Table Of Contents
Real Time Clock: B-SA704-RTC-QM-R -------------------------------------------------------------------- 6- 1 Expansion I/O Board: B-SA704-IO-QM-R ----------------------------------------------------------------- 7- 1 CAUTION! 1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC. 2. The contents of this manual may be changed without notification. -
Page 3: Cutter Module: B-Sx208-Qm-R
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 1. Cutter Module: B-SX208-QM-R INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT WARNING! 1. Turn the printer power off and disconnect the power cord before installing an optional equipment. 2. Be careful not to pinch your fingers or hands with the covers. 3. - Page 4 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 1. Cutter Module: B-SX208-QM-R Remove the six screws (B-4x6, FL-4x6 and B-3x8) to detach the left side cover. B-4x6 Screw FL-4x6 Screw B-3x8 Screw Left Side Cover B-4x6 Screw Remove the four FL-4x6 screws to detach the front cover. FL-4x6 Screw FL-4x6 Screw FL-4x6 Screw...
- Page 5 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 1. Cutter Module: B-SX208-QM-R Attach the cutter support plate to the main frame with the two screws (FL-4x6). Main Frame FL-4x6 Screw FL-4x6 Screw Cutter Support Plate Connect the cutter harness to CN3 on the cutter interface PC board through the opening of the cutter unit.
- Page 6 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 1. Cutter Module: B-SX208-QM-R Connect the cutter harness to the connector on the printer through the opening of the main frame. Main Flame Opening Connector Cutter Harness 10. Mount the cutter cover with the two screws. Fit the cutter cover into the cutter attaching screws and secure the cutter cover with the two screws.
- Page 7 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 1. Cutter Module: B-SX208-QM-R • Adjusting the Cutter Guide Plates After attaching the cutter unit the following adjustment procedure should be employed to prevent paper jams. Attach the cutter guide plate A with the two SM-4x6C screws so that the fixed cutter is positioned 0.1 mm to 0.4 mm above the bottom of the cutter guide plate A.
-
Page 8: Strip Module: B-Sx908-H-Qm-R
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 2. Strip Module: B-SX908-H-QM-R 2. Strip Module: B-SX908-H-QM-R B-SX908-H-QM-R is an optional strip module for the B-SX6T/SX8T Series. • Packing List The following parts are supplied with the kit. Make sure you have all items shown below. Strip Unit (1 pc.) Strip Harness (1 pc.) Installation Manual (1 copy) - Page 9 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 2. Strip Module: B-SX908-H-QM-R Remove the four FL-4x6 screws to detach the front cover. FL-4x6 Screw FL-4x6 Screw FL-4x6 Screw Remove the SM-4x8 screw and operation panel harness to detach the operation panel. Operation Panel SM-4x8 Screw Operation Panel Harness Connect the strip harness to CN5 on the PWM PC Board through the opening of the strip base.
- Page 10 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 2. Strip Module: B-SX908-H-QM-R Install the strip unit into the printer with the four FL-4x6 screws which were removed in step 4. Strip Unit FL-4x6 Screw FL-4x6 Screw FL-4x6 Screw Connect the strip harness to the connector on the printer through the opening of the main frame. Main Frame Opening Connector...
-
Page 11: Ribbon Saving Module: B-Sx908-R-Qm-R
EO15-33002 3. Ribbon Saving Module: B-SX908-R-QM-R 3. Ribbon Saving Module: B-SX908-R-QM-R B-SX908-R-QM-R is an optional strip module for the B-SX6T Series. • Packing List The following parts are supplied with the kit. Make sure you have all items shown below. - Page 12 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 3. Ribbon Saving Module: B-SX908-R-QM-R Remove the two B-4x6 screws to detach the print head front plate. Remove the four SM-4x8 screws to detach the blind plate (R) and blind plate (L). Blind Plate (L) Blind Plate (R) SM-4x8 Screw B-4x6 Screw...
- Page 13 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 3. Ribbon Saving Module: B-SX908-R-QM-R Fit the locking supports into the RSV PC board, then connect the solenoid (L) harness to CN1 on the RSV PC board. Solenoid (L) Harness RSV PC Board Attach the blind plate (R) to the solenoid (R) with the two SM-3x5 screws. Blind Plate (R) SM-3x5 Screw Solenoid (R)
- Page 14 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 3. Ribbon Saving Module: B-SX908-R-QM-R 10. Connect the solenoid (R) harness to the head block harness. Solenoid (R) Harness 11. While inserting the head up link into the spring pin of the solenoid, attach the solenoids (L) and (R) to the head block.
- Page 15 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 3. Ribbon Saving Module: B-SX908-R-QM-R 12. Insert piled 12 pieces of tag paper (0.16-mm thick, I-BEST-S is recommended.) between the print head and the platen. Then turn the head lever to the LOCK position. Head Lever LOCK Position Tag Paper...
- Page 16 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 3. Ribbon Saving Module: B-SX908-R-QM-R 14. After installing the solenoids (L) and (R), reassemble the print head front plate so that this part fits into the slot of the shaft. Shaft Slot Print Head Front Plate 15.
-
Page 17: Wireless Lan Module: B-Sa704-Wlan-Qm
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 4. Wireless LAN Module: B-SA704-WLAN-QM-R 4. Wireless LAN Module: B-SA704-WLAN-QM-R B-SA704-WLAN-QM-R is an optional wireless LAN module for the B-SX6T/SX8T Series, B-SA4TM/SA4TP Series and B-852-QQ/QP-R Series . • Packing List The following parts are supplied with the kit. Make sure you have all items shown below. Wireless LAN Board (1 pc.) Antenna Cover (1 pc.) SMW-3x6 Screw (4 pcs.) - Page 18 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 4. Wireless LAN Module: B-SA704-WLAN-QM-R • Installation Procedure Turn the power off. Open the right side cover and top cover. Top Cover Right Side Cover Remove the six screws (B-4x6, FL-4x6 and B-3x8) to detach the left side cover. B-4x6 Screw FL-4x6 Screw B-3x8 Screw...
- Page 19 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 4. Wireless LAN Module: B-SA704-WLAN-QM-R 5. Put the antenna of the wireless LAN board out of the opening of the back of the printer. Care must be taken not to hit the antenna against the printer frame, as damaged antenna may affect the performance.
- Page 20 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 4. Wireless LAN Module: B-SA704-WLAN-QM-R Secure the wireless LAN board onto the MAIN PC board with the SMW-3x6 screw. Connect the wireless LAN power cable to CN12 on the MAIN PC board. Wireless LAN Board SMW-3x6 Screw MAIN PC Board CN12...
- Page 21 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 4. Wireless LAN Module: B-SA704-WLAN-QM-R 10. Fit the antenna cover to the back of the printer. Secure it with the SMW-3x6 screw. Antenna Cover SMW-3x6 Screw Pass the LAN cable through the cut of the antenna cover. LAN Cable 11.
- Page 22 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 4. Wireless LAN Module: B-SA704-WLAN-QM-R • Country Code As available frequency bands are different from country to country, be sure to set a country code before installing a wireless LAN module in a user’s printer. Also, ask an end user to confirm a country code. Use of a wireless LAN module with a wrong country code could violate each country’s Laws and Regulations for Radio Equipment, and violators could be subject to penalties.
-
Page 23: Serial Interface Board: B-Sa704-Rs-Qm-R
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 5. Serial Interface Board: B-SA704-RS-QM-R 5. Serial Interface Board: B-SA704-RS-QM-R B-SA704-RS-QM-R is an optional expansion I/O board for the B-SX6T/SX8T Series, B-SA4TM/SA4TP and B-852-QQ/QP-R Series. • Packing List The following parts are supplied with the kit. Make sure you have all items shown below. SIO PC Board (1 pc.) Locking Support (1 pc.) PCB Support Plate (1 pc.) - Page 24 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 5. Serial Interface Board: B-SA704-RS-QM-R Remove the six screws (B-4x6, FL-4x6 and B-3x8) to detach the left side cover. B-4x6 Screw FL-4x6 Screw B-3x8 Screw Left Side Cover B-4x6 Screw 4. Remove the two SMW-3x6 screws to detach the blind plate. Blind Plate SMW-3x6 5.
- Page 25 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 5. Serial Interface Board: B-SA704-RS-QM-R Connect the serial interface cable of the SIO PC board to CN12 on the MAIN PC board. MAIN PC Board CN12 SIO PC Board Serial Interface Cable Fit the locking support into the MAIN PC board. Locking Support MAIN PC Board Secure the SIO PC board to the back of the printer with the two SMW-3x6 screws.
-
Page 26: Real Time Clock: B-Sa704-Rtc-Qm-R
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 6. Real Time Clock: B-SA704-RTC-QM-R 6. Real Time Clock: B-SA704-RTC-QM-R B-SA704-RTC-QM-R is an optional real time clock for the B-SX6T/SX8T series, B-SA4TM/SA4TP series and B-852-QQ/QP-R series. NOTE: When the B-SA704-IO-QM-R Expansion I/O board or B-SA704-RS-QM-R serial interface board has already been installed in the printer, the interface cable of the real time clock cannot be connected to the MAIN PC board. - Page 27 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 6. Real Time Clock: B-SA704-RTC-QM-R Remove the six screws (B-4x6, FL-4x6 and B-3x8) to detach the left side cover. B-4x6 Screw FL-4x6 Screw B-3x8 Screw Left Side Cover B-4x6 Screw 4. Place the lithium battery into the battery socket in the direction of the arrow. Battery Socket Lithium Battery NOTES: 1.
- Page 28 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 6. Real Time Clock: B-SA704-RTC-QM-R Attach the real time clock to the printer with the SMW-4x8 screw. Connect the interface cable to CN501 on the MAIN PC board. SMW-4x8 Screw Real Time Clock CN501 MAIN PC Board Interface Cable Attach the left side cover which was removed in Step 3 to the back of the printer.
-
Page 29: Expansion I/O Board: B-Sa704-Io-Qm-R
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 7. Expansion I/O Board: B-SA704-IO-QM-R 7. Expansion I/O Board: B-SA704-IO-QM-R B-SA704-IO-QM-R is an optional expansion I/O board for the B-SX6T/SX8T Series, B-SA4TM/SA4TP Series and B-852-QQ/QP-R Series. • Packing List The following parts are supplied with the kit. Make sure you have all items shown below. Expansion I/O Board (1 pc.) Blind Plate (1 pc.) SMW-3x6 Screw (3 pcs.) - Page 30 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 7. Expansion I/O Board: B-SA704-IO-QM-R Remove the six screws (B-4x6, FL-4x6 and B-3x8) to detach the left side cover. B-4x6 Screw FL-4x6 Screw B-3x8 Screw Left Side Cover B-4x6 Screw 4. Remove the two SMW-3x6 screws to detach the blind plate. Blind Plate SMW-3x6 NOTE:...
- Page 31 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33002 7. Expansion I/O Board: B-SA704-IO-QM-R 6. Connect the interface cable to CN4 on the MAIN PC board. Expansion I/O Board MAIN PC Board Interface Cable 7. Attach the supplied blind plate to the back of the printer with the supplied two SMW-3x6 screws. Blind Plate SMW-3ｘ6 Screw NOTE: The blind plate is not required to be attached when the optional serial interface board is also installed.