hit counter script
Download
Share
Print this page
Toshiba B-SX6T Series Supply Loading Instructions
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Printer
  5. B-SX6T Series
  6. Supply loading instructions

Toshiba B-SX6T Series Supply Loading Instructions

Hide thumbs Also See for B-SX6T Series:

Advertisement

Quick Links

Download this manual
TOSHIBA Thermal Printer
B-SX6T/SX8T Series
SUPPLY LOADING INSTRUCTIONS
This sheet contains only the media and ribbon loading procedures. Please be sure to read the Owner's Manual in
the CD-ROM for further information about this printer.
1. LOADING THE MEDIA
1. Do not touch any moving parts. To reduce the risk of fingers, jewellery, clothing, etc., being drawn into the
moving parts, be sure to load the media once the printer has stopped moving completely.
2. The Print Head becomes hot immediately after printing. Allow it to cool before loading the media.
3. Care must be taken not to pinch your fingers when opening or closing the Top Cover or Right Side
Cover.
4. Be careful not to pinch your fingers by the Supply Holder Frame or Media Holders when loading the media.
1. Ne touchez pas aux éléments en mouvement. Pour éviter les risques que les doigts, les bijoux les habits,
etc. soient tirés vers les éléments en mouvement, rassurez-vous de charger le média lorsque l'imprimante
est arrêtée complètement.
2. La tête chauffe beaucoup en imprimant. Laissez-la refroidir avant de charger le média.
3 .Prenez garde à ne pas vous pincer les doigts lorsque vous manipulez la capot supérieur ou le capot
coté droit.
4. Prenez garde à ne pas vous pincer les doigts lorsque vous manipulez le cadre support média ou les
guides lors du chargement média.
The following procedure shows the steps to properly load the media into the printer so that it feeds straight and
true through the printer.
The printer prints both labels and tags.
1. Install one of the Media Holders onto the Supply Shaft.
Turn the Locking Lever of the Media Holder to "Close" position to fix the Supply Shaft with the Media
Holder.
Media Holder
Supply Shaft
2. Place a media roll onto the Supply Shaft and push the media against the Media Holder.
Supply Shaft
! 0 0 T S C C 0 1 6 7 8 1 1 !
WARNING!
AVERTISSEMENT!
Locking
Lever
Media
1
Open
Close

Advertisement

loading

Related Manuals for Toshiba B-SX6T Series

Summary of Contents for Toshiba B-SX6T Series

  • Page 1 ! 0 0 T S C C 0 1 6 7 8 1 1 ! TOSHIBA Thermal Printer B-SX6T/SX8T Series SUPPLY LOADING INSTRUCTIONS This sheet contains only the media and ribbon loading procedures. Please be sure to read the Owner’s Manual in the CD-ROM for further information about this printer.
  • Page 2 3. Install the other Media Holder onto the Supply Shaft from the opposite side. Turn the Locking Lever of the Media Holder to the “Close” position. “Close” Position Media Holder Media Supply Shaft Locking Lever 4. Set the Head Lever to the “OPEN” position. Head Lever “OPEN”...
  • Page 3 Place the assembled Media Holder onto the Supply Holder Frame, and feed the media between the two Media Guides. Turn the Locking Lever of the Media Holder to the “Open” position, and push the Media Holders toward the centre to place the media at the centre on the Supply Shaft. Then, lock the position of the media by returning the Locking Levers to the “Close”...
  • Page 4 10. After loading the media, it may be necessary to set the position of the Media Sensor used to detect the print start position for label or tag printing. This printer is equipped with two media sensors: Fixed sensor and Movable sensor. Each of them is comprised of a Feed Gap Sensor and a Black Mark Sensor.
  • Page 5 The following procedures show how to adjust the position of the movable sensor. Feed Gap Sensor position adjustment When using a label stock without black marks, the Feed Gap Sensor is used to detect the print start position. Looking inside of the Media Outlet, move the Movable Sensor by rotating the Adjustment Knob until the Feed Gap Sensor aligns with a gap.
  • Page 6 11. There are three issue modes available on this printer. How to set the media for each mode is provided below. Batch mode In the batch mode, the media is continuously printed and fed until the number of labels/tags specified in the issue command have been printed.
  • Page 7 Cut mode (Option) When the optional Cutter Module is fitted, the media is automatically cut. (1) Insert the leading edge of the media into the Media Outlet of the Cutter Module. WARNING! The cutter is sharp, so care must be taken not to injure your fingers when handling the cutter.

  • Page 8: Loading The Ribbon

    2. LOADING THE RIBBON WARNING! 1. Do not touch any moving parts. To reduce the risk of fingers, jewellery, clothing, etc., being drawn into the moving parts, be sure to load the ribbon once the printer has stopped moving completely. 2.
  • Page 9 3. Fit the core of the Ribbon Supply Roll into the Ribbon Holders (Supply side), aligning the notch of the ribbon core with the protrusion of the Ribbon Holder. Ribbon Holder (Supply Side) Ribbon Core Ribbon Supply Roll Notch Ribbon Supply Roll Fit the protrusion into the notch.
  • Page 10 3. When using a non transparent ribbon, choose the Non trans ribbon for the parameter setting in the system mode. Transparent ribbon has been selected as default. PRINTED IN INDONESIA © 2011-2015 TOSHIBA TEC CORPORATION All Rights Reserved EO2-33023D 1-11-1, Osaki, Shinagawa-ku, Tokyo 141-8562, JAPAN...

This manual is also suitable for:

B-sx8t series