Table of Contents
Advertisement
4-2 Back Space Editing
You can record multiple scenes as a single sequence with
no noise or breakup between scenes (back space editing).
Proceed as follows.
PB LEVEL
1
3
REC LEVEL
CHARACTR
EMPH
EMPH
1
3
ON
0
PB/EE
–10
PB
2
4
–20
CONFI
–30
ENABLE
–40
2
4
CTL/TC
1
2
TC
59.94i
SDI ASMBL CONFI ON RECORDER
R/P LEVEL CTL
ASSEMBLE
OFF
LTC
DF VITC LTC EXT-LTC R-RUN REM:00
VAR
LEVEL
TCG SET
00:00:00:00.
PRESET
HOME
SHIFT
SHIFT
REC INHI
ON
REW
PLAY
F FWD
PHONES
OFF
PAGE
KEY INHI
ON
HOME
OFF
1
1
Press the REC button and PLAY button
simultaneously.
Recording beigns.
2
When recording finishes, press the PAUSE button.
The tape is rewound a little to a point just
before where it was when you pressed the PAUSE
button, and the unit enters recording pause mode.
Note
When recording is paused, do not do any of the
following (if you do, back space editing will be
interrupted):
• Eject a cassette.
• Play back, rewind, or fast forward the tape.
• Press the STOP button.
3
At the next scene, press the PAUSE button.
The tape moves to the recording start position, and
recording starts.
4
Repeat steps 2 and 3 to record more scenes.
5
When you are finished recording scenes, press the
STOP button.
Recording continuous timecode
Set setup menu item 610 to a setting other than MANU.
For details on setup menu item 610, see page 71.
HDW-S280
EJECT
MULTI CONTROL REMOTE
DISPLAY
HD
EMPH
EMPH
INPUT : ANA
MENU
CH1 IN :
–60
0
COND
CH2 IN :
–4
PUSH
–10
RESET
OUT :
+4
PITCH CTL
JOG/SHUTTLE
–20
MONI L :
1
–30
BANK 2
–40
MONI R :
2
PREROLL
D-STOP
DOLBY NR
3
4
P ROLL
M
STOP
REC
PAUSE
STANDBY
5 2,3
4-3 Sequential Recording
When you connect two HDW-S280 units as shown below,
you can perform sequential recording from one unit to
another.
HD SDI video/audio signal
Starting VTR
-AC IN
-
POWER
AC IN
REMOTE
ON
OFF
SDI OUT
COMPOSITE OUT
1
2
1
2
(SUPER)
(SUPER)
INPUT
HD SDI
OUTPUT
TIME CODE
IN
MONI
1
2
IN
HD SDI
(SUPER)
AUDIO INPUT
AUDIO OUTPUT
INPUT IN
1
2
1
HD SDI
INPUT MONI
Ω
75
coaxial cable with
BNC connectors
(not supplied)
Ω
75
coaxial cable with
BNC connectors
(not supplied)
Second VTR
-AC IN
-
POWER
AC IN
REMOTE
ON
OFF
SDI OUT
COMPOSITE OUT
1
2
1
2
(SUPER)
(SUPER)
INPUT
HD SDI
OUTPUT
TIME CODE
IN
MONI
1
2
IN
HD SDI
(SUPER)
AUDIO INPUT
AUDIO OUTPUT
INPUT IN
1
2
1
If you use only two cassettes, the last 78 minutes recorded
can be obtained at any time.
If you change cassettes about every 38 minutes, endless
recording is possible.
Follow the procedures below.
You can perform the front panel operations on the both
units during sequential recording.
Back Space Editing / Sequential Recording
Reference video signal
Ω
75
coaxial cable with BNC
connectors (not supplied)
REF
INPUT
DC IN 12V
VIDEO CONTROL
REF. INPUT
IOUT
REMOTE 9P
REMOTE 9P
AUDIO MONITOR OUTPUT
2
R
L
REF
INPUT
9-pin remote
control cable
(not supplied)
REF
INPUT
DC IN 12V
VIDEO CONTROL
REF. INPUT
IOUT
REMOTE 9P
REMOTE 9P
AUDIO MONITOR OUTPUT
2
R
L
41
- Quick Links:
- Error Messages
Hide quick links:
Advertisement
Table of Contents
