Page 2
VIEWS AND IN THE PARTS LIST ARE CRITICAL TO REMOVING THE ANODE. SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS AP- PEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE- MENTS PUBLISHED BY SONY. – 2 –...
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 SECTION 1 SELF DIAGNOSIS FUNCTION Diagnostic Errors The errors indicated below can be read using an Error Reader Display (Part Number S-188-900-10) connected to the service connector. Once an error has been detected it will then be displayed on the two digit error reader.
Page 5
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 Protection Error (Error 2): Once every main loop (approximately 200ms OSD mode, 50ms text or menu mode), the micro checks the protection pin (pin 66). If the protection pin is high 6 successive times, a protection error is diagnosed. The protection pin is not checked during the first 3-4 seconds after AC on.
Page 6
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 General I C Device Run-time Errors (Errors 18-22): 18 - No acknowledge from Jungle when attempting to initialize 19 - No acknowledge from Jungle when attempting to read registers 20 - AV Switch cannot complete reset during initialization...
Page 7
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 Error Display Mode Error Display Mode is entered by the following sequence of commands: Standby → Information → Digit 5 → Volume Down → TV This mode will display a special menu, which will list all possible errors and the number of occurrences of each error (0 – 255, as stored in the NVM).
Page 8
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 TT command table TT Mode is available by pressing the test key twice. It is exited by pressing 0 twice, or by pressing the Test key, or by pressing the TV key or by switching the set into standby.
Page 9
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 Code Function Code Function No Function (41PX1/41PX1K) Set Screen Size (41PX1/41PX1K) Auto Picture OFF (41PX1R) MSP BG Filter Disabled (41PX1R) No Function (41PX1/41PX1K) Wide Setup Auto Cut Off Enable (41PX1R) Velocity Modulation ON Set Colour to Minimum and Picture to Maximum...
VIDEO VIDEO PROGR MENU VTR 1 2 3 4 DVD RM 892 VIDEO PROGR MENU RM 892...
Page 11
LANGUAGE English Deutsch LANGUAGE Fran ais English Deutsch Espa ol Fran ais Espa ol Suomi Suomi Nederlands Portugu s Nederlands Suenska Dansk Portugu s Norsk Italiano Suenska Česki Magyar Eλλnvιkά Dansk Select Language: Norsk Confirm: OK Italiano Česki Magyar Eλλnvιkά Select Language: Confirm: OK LANGUAGE...
Page 12
PROG SYS CHAN LABEL C 28 BBC-W C 40 MV-CH C 41 TVE-1 VIDEO C 31 TVE-2 C 34 ANT-3 C 27 TELE 5 VIDEO C 47 C PLUS C 44 - - - - - C 23 - - - - - C 35 CNN - Select PROG:...
Page 13
MENU PICTURE CONTROL PICTURE CONTROL Picture Mode Personal Picture Mode Personal Contrast Reset Contrast Reset Format Format SOUND CONTROL SOUND CONTROL Sound Mode Personal Sound Mode Personal Balance Reset Balance Reset Dolby Virtual Dolby Virtual Dual Sound Mono Volume Offset Dual Sound Mono Volume Offset...
Page 14
PICTURE CONTROL Picture Mode Personal Contrast Reset Format PRESET Auto Programme Manual Programme Preset Further Programme Preset AV Label Preset Programme Sorting Parental Lock Language Convergence PRESET Please confirm that Auto Programme antenna is connected Manual Programme Preset Further Programme Preset AV Label Preset Confirm: OK Programme Sorting...
Page 15
PICTURE CONTROL PICTURE CONTROL VIDEO VIDEO Picture Mode Personal Picture Mode Personal Contrast Contrast Reset Reset Format Format PRESET PRESET Auto Programme Auto Programme Manual Programme Preset Manual Programme Preset Further Programme Preset Further Programme Preset AV Label Preset AV Label Preset Programme Sorting Programme Sorting Parental Lock...
Page 16
PICTURE CONTROL PICTURE CONTROL VIDEO Picture Mode Personal VIDEO Picture Mode Personal Contrast Contrast Reset Reset Format Format PRESET PRESET Auto Programme Manual Programme Preset Auto Programme Further Programme Preset Manual Programme Preset AV Label Preset Further Programme Preset Programme Sorting AV Label Preset Parental Lock Programme Sorting...
Page 17
PICTURE CONTROL PICTURE CONTROL VIDEO VIDEO Picture Mode Personal Picture Mode Personal Contrast Contrast Reset Reset Format Format PICTURE CONTROL PICTURE CONTROL Picture Mode Personal Picture Mode Personal Contrast Reset Contrast Reset Format Format PICTURE MODE Picture Mode Personal Brightness Colour Sharpness PROGR...
Page 18
PICTURE CONTROL VIDEO VIDEO Picture Mode Personal Contrast Reset Format SOUND CONTROL Sound Mode Personal Balance Reset Dolby Virtual Dual Sound Mono Volume Offset Volume Dual Sound Mono Speaker Main SOUND MODE Mode Personal Treble Bass PROGR PROGR MENU MENU RM 892 RM 892 Personal...
Page 19
PICTURE CONTROL VIDEO VIDEO Picture Mode Personal Contrast Reset Format TIMER Index TELETEXT TELETEXT Programme Index Programme Sleep Timer News News Sport Weather Sport Weather TIMER Sleep Timer 1:00 PROGR PROGR MENU MENU RM 892 RM 892 TELETEXT TELETEXT Index Programme News Sport...
Page 21
PICTURE CONTROL VIDEO Picture Mode Personal Contrast Reset Format VIDEO CONNECTION TV Screen [TV - - - - - - -] Output [AV1 - - - - - - -] PROGR MENU RM 892 VIDEO VTR 1 2 3 4 DVD...
Page 22
PICTURE CONTROL VIDEO Picture Mode Personal Contrast Reset Format PRESET Auto Programme Manual Programme Preset Further Programme Preset AV Label Preset Programme Sorting Parental Lock Language Convergence PRESET Auto Programme Manual Programme Preset Further Programme Preset AV Label Preset Programme Sorting Parental Lock Language Convergence...
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 3-6. E BOARD REMOVAL 1 Five screws (+BVTP3 × 12) 2 E board 3-7. G BOARD REMOVAL 1 Four claws 2 G board – 26 –...
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 4-5. 2-POLE MAGNET ADJUSTMENT 4-7. GREEN, RED AND BLUE FOCUS (GREEN AND RED) ADJUSTMENT 4-7-1. Green, Red and Blue Lens Focus Adjustment 1. Receive the Dot signal and set PICTURE to 80%, BRIGHT- NESS to 50%.
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 SECTION 5 SAFETY RELATED ADJUSTMENT When replacing the following components marked with ] on E BOARD the schematic diagram, always check hold-down voltage and if – CONDUCTOR SIDE – necessary re-adjust. CN810 CN505 Part Replaced ([)
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 SECTION 6 ELECTRICAL ADJUSTMENTS 3. Press “MENU” on the commander to obtain the following 6-1. HOW TO ENTER THE SERVICE MODE menu on the screen. (With some models, display items may be different from 6-1-1. Adjustment Method with Commander...
Page 33
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 Geometry ( : No need to adjust) GEOMETRY ADJUSTMENT MSP ADJUSTMENT CONCCT FAWCTIST 16:9 V Size 0 - 63 AGC On / Off ON/OFF V Position 0 - 63 Constant Gain CDB 0 - 20 S Correction...
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 Current TV Status Convergence Depends on the signals TV STATUS RE-2A(TT09) PAL, SECAM : 50 NTSC : 60 Mode Item No. Text System C Text-2 Dolby Enabled DSP Present Text Language Set East/Greek Menu Language Set...
Page 35
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 Initial Data Item Adjustment Data Range Mode Name / Description Device Number Item 16 : 9 4 : 3 CENT –127 ~ +127 GREEN V CENTER CXP86213 SKEW –127 ~ +127 –17 –17 GREEN V SKEW –127 ~ +127...
Page 36
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 Initial Data Item Adjustment Data Range Mode Name / Description Device Number Item 16 : 9 4 : 3 CENT –95 ~ +96 –19 –19 BLUE V CENTER CXP86213 SKEW –95 ~ +96 BLUE V SKEW –127 ~ +127...
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 6-2. REGISTRATION ADJUSTMENT CENTER ADJUSTMENT 1. Adjust H Position and V Position. 6-2-1. Registration Adjustment Method 1. Turn on the main power switch of the set and enter into standby mode. H Position 2. Press the following sequence of buttons on the Remote Commander.
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 MAIN DEFLECTION ADJUSTMENT 6-2-3. Sub Deflection Adjustment 1. Adjust V Linearity. 1. Receive the PAL SPCB signal. Correct linearity of the horizontal top and bottom lines. 2. Select 16 : 9 mode. (blue key)” : 4 : 3 b 16 : 9 Press “...
Page 39
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 GREEN VERTICAL LINE ADJUSTMENT GREEN HORIZONTAL LINE ADJUSTMENT 1. Receive the PAL SPCB signal. 1. Receive the PAL SPCB signal. 2. Carefully watching out for the GH CENT screen center sec- 2. Finely adjust the center position of the vertical line at the tion, adjust GH CENT, GH BOW, GH SKEW.
Page 40
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 GREEN VERTICAL SIZE ADJUSTMENT GREEN HORIZONTAL SIZE ADJUSTMENT 1. Receive the Internal pattern (crosshatch) signal. 1. Receive the Internal pattern (crosshatch) signal. 2. Adjust GV MSIZ so that the sizes at the top and bottom and 2.
Page 41
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 GREEN HORIZONTAL SYMMETRICAL PIN DISTORTION GREEN HORIZONTAL QUATERNARY ADJUSTMENT ADJUSTMENT 1. Receive the Internal pattern (crosshatch) signal. 1. Receive the Internal pattern (crosshatch) signal. 2. Adjust GH 4PIN, to correct the 4th order distortion. 2. Adjust GH MPIN to correct pin distortion at both edges of 3.
Page 42
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 GREEN VERTICAL ASYMMETRICAL PIN DISTORTION GREEN VERTICAL 4TH ORDER DISTORTION (2ND-ORDER DISTORTION) ADJUSTMENT ADJUSTMENT 1. Receive the Internal pattern (crosshatch) signal. 1. Receive the Internal pattern (crosshatch) signal. 2. Correct the asymmetrical pin distortion at the top and bot- 2.
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 RED REGISTRATION ADJUSTMENT AUTO CONVERGENCE PRESET 1. Receive the Internal pattern (crosshatch) signal. 1. Set in the TT mode. GH GSEL = “00” (Green + Red) 2. Press “ (AUTO CONVERGENCE)” button on front 2. Adjust so that the red lines lay on the green lines.
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 6-5. WHITE BALANCE ADJUSTMENT 6-7. SUB CONTRAST ADJUSTMENT 1. Receive the Monoscope signal. (A or AE Board) 2. Set in the service mode and select “Picture Adjustment”. 1. Receive the PAL video color bar signal. 3. Adjust “Sub Brightness” so that the signal 10 IRE section White 100% barely glows.
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 SECTION 7 DIAGRAMS 7-1. BLOCK DIAGRAMS IC201 IC103 IC204 IC301 SHADING TU101 VIDEO SW DIGITAL COMB FILTER YC SW BUFF CN301 BUFFER BUFFER BUFFER Y BUFFER VIDEO TV IN CVBS OUT FL102 ADIN Q107,108 SVHS-Y IN...
Page 46
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 IC103 IC201 DL SW IC204 TU101 VIDEO SW DIGITAL COMB FILTER Q118 YC SW BUFFER VIDEO BUFFER BUFFER BUFFER LUMINANCE BUFFER Y LPF BUFFER VIDEO TV IN CVBS OUT Q103, A/D IN Q105,106 Q114 Q117 Q201...
Page 47
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 IC301 CN301 BUFFER CVBS IN R OUT 1 RED DRIVE Q303 2 GRN DRIVE 3 BLUE DRIVE BUFFER SVHS-Y IN G OUT 4 9V Q334 5 GND TO CR BOARD 6 CUT OFF BUFFER CN703 B OUT...
Page 50
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 (RED AMP) (GREEN AMP) (BLUE AMP) RED AMP V901 V902 V903 Q704,703 GREEN AMP BLUE AMP PICTURE TUBE PICTURE TUBE PICTURE TUBE Q733,732 Q762,763 Q701 HV R HV G HV B CN703 CN706 CN736 CN737 CN765...
Page 51
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 41PX1/41PX1K CN4901 S3006 IC3002 IR RECEIVER V IN V OUT CN3003 D3008 CN3001 AC (L) IN TO A BOARD SIRCS AV LINK CN4502 AC (N) IN J4901 MODE STBY 5V STBY 5V (AV3) TO G BOARD...
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 7-2. FRAME SCHEMATIC DIAGRAM (1) (41PX1/41PX1K) PHOTO SENSOR AUDIO R OUT UPPER CN4902 L IN L IN AUDIO R OUT AUDIO R IN :S-MICRO R IN R IN CN4501 AUDIO R IN LEFT AUDIO L OUT...
Page 53
KP-41PX1/41PX1K/41PX1R FRAME SCHEMATIC DIAGRAM (2) (41PX1R) RM-892 RM-892 RM-862 PHOTO SENSOR (AV1) (AV2) UPPER CN2702 L IN FOR CHECK WHT-L :S-MICRO R IN LEFT (AV3) L OUT (SMART LINK) R OUT RIGHT (AV IN/OUT) CN201 DUAL SCART LOWER CVBS/Y IN...
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 (4) Schematic Diagram of A (4/5) Board (41PX1/41PX1K) LINK IN AV LINK IN TO A(2/5) LINK OUT AV LINK OUT U-PC DISABLE TO A(1/5) DISABLE PJE TO A(1/5,3/5) TO A4/5,A5/5_13 TO A4/5,A5/5_14 TO A4/5,A5/5_15 TO A4/5,A5/5_16...
KP-41PX1/41PX1K/41PX1R (9) Schematic Diagram of AE (4/5) Board (41PX1R) RM-892 RM-892 RM-862 U-PC DISABLE TO AE(1/5) AGC MONI TO AE(1/5,3/5) TO AE(1/5) DISABLE PJE TO AE4/5,AE5/5_9 TO AE4/5,AE5/5_10 TO AE4/5,AE5/5_11 VIDEO TO AE4/5,AE5/5_12 CVBS STDBY 5V TO AE(1/5) CVBS C373...
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 (14) Schematic Diagram of E (1/4) Board TO E1/4,E2/4_1 TO E1/4,E2/4_2 TO E1/4,E2/4_3 CN508 :FASTON TO E1/4,E2/4_4 TO E1/4,E2/4_5 R809 R823 TO D(3/3)BOARD Q801 Q803 4.7k R867 CN1502 2SC3311A 2SC3311A BUFF BUFF R878 100k Q812 R704...
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 (16) Schematic Diagram of E (3/4) Board (3/4) (HV) CN507 :S-MICRO TO PICTURE HV(R) TUBE R HV.REG TO E2/4,E3/4_21 TO PICTURE HV(G) STDBY 7V TO E2/4,E3/4_22 TUBE G STDBY 7V TO E2/4,E3/4_23 TO PICTURE HV(B) TUBE B <HV.BLOCK>...
Page 84
KP-41PX1/41PX1K/41PX1R NOTE: RM-892 RM-892 RM-862 The circuit indicated as left contains high voltage of over 600 Vp-p. Care must be paid to prevent an electric shock in H DEFRECTION, inspection or repairing. HV, DY DRIVE — E BOARD — • E BOARD SEMICONDUCTOR...
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 USER CONTROL, MAIN SWITCH (25) Schematic Diagram of H1 Board — H1 BOARD — IC3002 SBX3081-51(20) IR RECEIVER USER CONTROL, R3004 MAIN SWITCH 220 1/10W STBY 5V D3002 D3003 CN3003 MTZJ-5.6B C3003 C3004 TO G BOARD...
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 SECTION 8 EXPLODED VIEWS NOTE: • Items marked " * " are not stocked since The components identified by shading they are seldom required for routine • Items with no part number and no ¡ and mark are critical for safety.
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 8-2. CABINET BLOCK The components identified by shading ¡ : 7-685-663-71 SCREW +BVTP 4X16 and mark are critical for safety. Replace only with part number specified. : 7-685-663-79 SCREW +BVTP 4X16 MECHASEAL BLOCK CHASSIS BLOCK REF.NO. PART NO.
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 8-3. MAIN BRACKET BLOCK The components identified by shading ¡ and mark are critical for safety. : 7-685-648-71 SCREW +BVTP 3X12 Replace only with part number specified. : 7-685-663-71 SCREW +BVTP 4X16 : 7-685-663-79 SCREW +BVTP 4X16 REF.NO.
KP-41PX1/41PX1K/41PX1R RM-892 RM-892 RM-862 8-4. MECHASEAL BLOCK The components identified by shading ¡ and mark are critical for safety. : 7-685-648-71 SCREW +BVTP 3X12 Replace only with part number specified. : 7-685-663-71 SCREW +BVTP 4X16 REF.NO. PART NO. DESCRIPTION REMARK REF.NO.
KP-41PX1/41PX1K/41PX1R The components identified by shading SECTION 9 ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. ELECTRICAL PARTS LIST The components identified by [ in this REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO.
Page 102
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK C217 1-162-970-11 CERAMIC CHIP 0.01µF C279 1-126-965-91 ELECT 22µF...
Page 103
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK C355 1-126-965-91 ELECT 22µF C4101 1-164-217-11 CERAMIC CHIP 150pF C356 1-162-970-11 CERAMIC CHIP 0.01µF...
Page 104
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK D370 8-719-047-16 DIODE BAS216 D401 8-719-069-60 DIODE UDZSTE-179.1B...
Page 105
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK Q106 8-729-120-28 TRANSISTOR 2SC1623-L5L6 Q107 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R...
Page 106
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK 1-216-809-11 RES-CHIP 1/16W R151 1-216-809-11 RES-CHIP 1/16W 1-216-809-11 RES-CHIP...
Page 107
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R272 1-218-285-11 RES-CHIP 1/16W R213 1-218-285-11 RES-CHIP 1/16W...
Page 108
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. A AE REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R345 1-216-864-11 SHORT R4029 1-216-833-11 RES-CHIP...
Page 109
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK C205 1-126-965-91 ELECT 22µF 1-163-017-00 CERAMIC CHIP 0.0047µF 10%...
Page 110
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK C277 1-164-505-11 CERAMIC CHIP 2.2µF C356 1-164-232-11 CERAMIC CHIP 0.01µF C278 1-164-505-11 CERAMIC CHIP 2.2µF...
Page 111
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK D214 8-719-069-60 DIODE UDZSTE-179.1B D215 8-719-069-60 DIODE UDZSTE-179.1B D216 8-719-069-55 DIODE UDZSTE-175.6B...
Page 112
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK Q113 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R 1-216-025-00 RES,CHIP 1/10W Q114...
Page 113
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R117 1-216-057-00 RES,CHIP 2.2K 1/10W R179 1-208-788-11 METAL CHIP 1.8K...
Page 114
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R236 1-216-113-00 RES,CHIP 470K 1/10W R310 1-216-033-00 RES,CHIP...
Page 115
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. AE G REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R1017 1-216-295-00 SHORT C6029 1-164-625-11 CERAMIC...
Page 116
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK D6016 8-719-052-91 DIODE D4SBS4-F Q6002 8-729-056-60 TRANSISTOR SPA07N60C2...
Page 117
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. G CB CG REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R6051 1-216-366-00 METAL OXIDE 0.56...
Page 118
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. CG CR REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK C737 1-107-662-11 ELECT 22µF 250V * A-1638-152-ACR BOARD, COMPLETE...
Page 119
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. CR D REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R711 1-216-487-11 METAL OXIDE C1602 1-163-009-11 CERAMIC CHIP 0.001µF...
Page 120
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK C1727 1-164-004-11 CERAMIC CHIP 0.1µF CN1804 * 1-564-508-11 PLUG, CONNECTOR 5P C1802 1-164-232-11 CERAMIC CHIP 0.01µF...
Page 121
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK Q1612 8-729-027-56 TRANSISTOR DTC143TKA-T146 IC1701 8-752-908-27 IC CXP86213-003S...
Page 122
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R1645 1-216-041-00 RES-CHIP 1/10W R1527 1-216-129-00 RES-CHIP 2.2M...
Page 123
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R1749 1-216-033-00 RES-CHIP 1/10W R1807 1-216-295-91 SHORT (41PX1/41PX1K)
Page 124
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R1841 1-216-049-00 RES-CHIP 1/10W C529 1-109-844-11 FILM 0.68µF...
Page 125
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK C838 1-104-665-11 ELECT 100µF <CONNECTOR> C839 1-137-374-11 MYLAR 0.047µF...
Page 126
• The components identified by [ in this manual KP-41PX1/41PX1K/41PX1R The components identified by shading have been carefully factory-selected for each set ¡ RM-892 RM-892 RM-862 and mark are critical for safety. in order to satisfy regulations regarding X-ray Replace only with part number specified.
Page 127
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R546 1-249-377-11 CARBON 0.47 1/4W R810 1-247-807-31 CARBON...
Page 128
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R871 1-249-417-11 CARBON 1/4W R931 1-215-445-00 METAL 1/4W...
Page 129
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. E H1 H2 REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R3002 1-216-073-91 RES-CHIP 1/10W R990...
Page 130
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. H2 U UE REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK <RESISTOR> R4915 1-216-043-91 RES-CHIP 1/10W...
Page 131
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. ZG ZR REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK * A-1652-078-AZG BOARD, COMPLETE Q1434 8-729-423-33 TRANSISTOR 2SC3311A-QRSTA...
Page 132
KP-41PX1/41PX1K/41PX1R The components identified by shading ¡ RM-892 RM-892 RM-862 and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK <RESISTOR> R1401 1-249-414-11 CARBON 1/4W R1402 1-249-414-11 CARBON...