Precautions On Adjusting; Adjusting Connectors - Sony DCR-TRV5 Service Manual
Digital video camera recorder
Hide thumbs
Also See for DCR-TRV5:
- Operating instructions manual (92 pages) ,
- Operating instructions manual (91 pages) ,
- Service manual (25 pages)
Table of Contents
Advertisement
3-1-2.
Precautions on Adjusting
1)
The adjustments of this unit are performed in the VTR mode
or camera mode.
To set to the VTR mode, set the power switch to "VTR" (or
"PLAYER") or set the "Forced VTR Power ON mode" using
the adjustment remote commander (Note 1).
To set to the Camera mode, set the power switch to "CAMERA"
or set the "Forced Camera Power ON mode" using the
adjustment remote commander (Note 2).
After completing adjustments, be sure to exit the "Forced VTR
Power ON Mode" or "Forced Camera Power ON Mode". (Note
3)
2)
MA-330 board (microphone amp, IR transmitter, remote
commander receiver) of the front panel block need not be
connected except during "Battery End Adjustment", "IR
Transmitter Adjustments" and "Audio System adjustments".
To remove, disconnect the following connector.
MA-330 board CN7001 (21P, 0.3mm)
3)
Removing CN006 (2P, 1.0mm) of VC-207 board means
removing the lithium 3V power supply (LI-65 board BT001) ,
data such as date, time, user-set menus will be lost. After
completing adjustments, reset these data. If CN006 has been
removed, the self-diagnosis data, data on history of use (total
drum rotation time etc. ) will be lost. Before removing, note
down the self-diagnosis data and the data on history use (data
of page: 2, address: 35 to 3D). (Refer to the "Service Mode"
for the data on the history use.)
4)
FP-699 board (Display switch, end search switch, panel
switches) need not be assembled. If removing it. Disconnect
the following connector.
VC-207 board CN002 (6P, 0.5mm)
5)
The viewfinder block (VF-124board) not be assembled. If
removing it. Disconnect the following connector.
VC-207 board CN001 (21P, 0.3mm)
6)
The lens block (CD-193 board) need not be connected except
during "Battery End Adjustment". To remove, disconnect the
following connectors.
VC-207 board CN201 (50P, 0.5mm)
7)
AU-207 board (Audio circuit) needs not be connected except
during "Audio System Adjustments" and "IR Transmitter
Adjustments". To remove, disconnected the following
connector.
VC-207 board CN011 (39P, 0.3mm)
8)
Use the following extension cable between DD-110 board
CN802 and VC-207 board CN010.
J-6082-395-A (80P, 0.4mm)
Note 1: Setting the "Forced VTR Power ON" mode (VTR mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the VTR power to be turned
on with the power switch (PS block) removed.
After completing adjustments, be sure to exit the "Forced VTR
Power ON mode".
Note 2: Setting the "Forced Camera Power ON" mode
(Camera mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the camera power to be turned
on with the power switch (PS block) removed.
After completing adjustments, be sure to exit the "Forced
Camera Power ON mode".
Note 3: Exiting the "Forced Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 0, address: 01, and set data: 00.
3-1-3.
Adjusting Connectors
Some of the adjusting points of the video section are concentrated
at VC-207 board CN005. Connect the measuring instruments via
the CPC-8 jig (J-6082-388-A). The following table lists the pin
numbers and signal names of CN005.
Pin No.
Signal Name
1
TCK
3
TDI
5
LINE V OUT
7
GND
9
VCC2
11
VCC1
13
LOCK
15
ENV OUT
17
TDO8
19
GND
5-31
Pin No.
Signal Name
2
TMS
4
GND
6
JSWP
8
RF MONITOR
10
AGC IN
12
EQ IN
14
BL 4.75
16
BL 4.75 (–)
18
VCO
20
EVF VG
Table 5-3-1.
Advertisement
Table of Contents
