Cd-193 (Ccd Imager) Printed Wiring Board - Sony DCR-TRV5 Service Manual

Digital video camera recorder

Hide thumbs Also See for DCR-TRV5:

Operating instructions manual (92 pages)

Operating instructions manual (91 pages)

Service manual (25 pages)

Table Of Contents

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

page of 165

/ 165
Contents
Table of Contents
Bookmarks

Table of Contents

DCR-TRV5/TRV5E

4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS

(In addition to this, the necessary note is printed in each block)

(For printed wiring boards)

(Measuring conditions voltage and waveform)

• b: Pattern from the side which enables seeing.

• Voltages and waveforms are measured between the measurement

(The other layers' patterns are not indicated.)

points and ground when camera shoots color bar chart of pattern

• Through hole is omitted.

box. They are reference values and reference waveforms. *

• Circled numbers refer to waveforms.

(VOM of DC 10 MW input impedance is used.).

• There are few cases that the part printed on diagram

• Voltage values change depending upon input impedance of VOM

isn't mounted in this model.

used.)

• Chip parts.

Transistor

Diode

1. Connection

Pattern box

1 2 3

3 2 1

5 4 3

1.5m

(For schematic diagrams)

• All capacitors are in mF unless otherwise noted. pF : m mF. 50V or

less are not indicated except for electrolytics and tantalums.

• Chip resistors are 1/10W unless otherwise noted.

kW=1000W, MW=1000kW.

• Caution when replacing chip parts.

New parts must be attached after removal of chip.

Front side of the lens

Be careful not to heat the minus side of tantalum capacitor, Because

it is damaged by the heat.

• Some chip part will be indicated as follows.

Example

C541

L452

22U

10UH

TA A

2520

2. Adjust the distance so that the output waveform of Fig. a and the

Kinds of capacitor

Fig. b can be obtain.

Temperature characteristics

External dimensions (mm)

• Constants of resistors, capacitors, ICs and etc with XX indicate that

they are not used.

In such cases, the unused circuits may be indicated.

• Parts with * differ according to the model/destination.

Refer to the mount table for each function.

• All variable and adjustable resistors have characteristic curve B,

unless otherwise noted.

• Signal name

A=B

XEDIT

EDIT

PB/XREC

PB/REC

• 2 : non flammable resistor

Fig. a (Video output terminal output waveform)

• 1 : fusible resistor

• C : panel designation

• A : B+ Line *

• B : B– Line *

• J

: IN/OUT direction of (+,–) B LINE. *

• C : adjustment for repair. *

• Circled numbers refer to waveforms. *

* Indicated by the color red.

Fig.b (Picture on monitor TV)

Note :

The components identified by

Les composants identifiés par

mark ! or dotted line with mark

une marque ! sont critiques

! are critical for safety.

pour la sécurité.

When indicating parts by reference number, pleas include

Replace only with part number

Ne les remplacer que par une

specified.

pièce portant le numéro spécifié.

the board name.

4-5

For printed wiring boards

• This board is six-layer print board. However, the pat-

terns of layers two to five have not been included in the

Electron beam

diagram.

scanned frame

• Chip parts

CRT picture frame

Transistor

There are few cases that the part printed on this

VF-124

(COLOR EVF)

diagram isn't mounted in this model.

CD-193

(CCD IMAGER)

FP-699

(FUNCTION KEY)

Precautions Upon Replacing CCD Imager

• The CD-193 board mounted as a repair part is not equipped with a

CCD imager.

When replacing this board, remove the CCD imager from the old

one and mount it onto the new one.

AU-204

• If the CCD imager has been replaced, carry out all the adjustments

(AUDIO PROCESSOR)

for the camera section.

• As the CCD imager may be damaged by static electricity from its

DD-110

(DRUM/CAPSTAN PWM DRIVE)

structure, handle it carefully like for the MOS IC.

VC-207

CAMERA PROCESS, FOCUS/ZOOM/IRIS DRIVE, VIDEO OUT, REC/PB PROCESS,

In addition, ensure that the receiver is not covered with dusts nor

RF INTERFACE, RGB DECODER, BLOCKING, ECC. TBC. CHCD, DV SIGNAL PROCESS,

AUDIO PROCESS, MODE CONTROL, EVR/AUDIO, MECHA CON/SERVO

exposed to strong light.

CCD IMAGER

4-6

CD-193